Sierra RedySmart Series Manual de usuario

QUICK START GUIDE

RedySmartTM Series

1 | RedySmart_v1_2020

Safety and General Information

1. For safe operation, please consider the process and ambient conditions for which the device is designed and speciﬁed at the time of

delivery. This information can be found on the data label on the instrument housing and in the Instruction Manual.

2. Do not remove the electronics housing to prevent damage to the unit. A damaged hologram seal will void the warranty.

3. There are no serviceable parts inside the unit. Repairs must be performed by qualiﬁed personnel only.

Installation and Electrical Connection

1. Do not use Teﬂon® tape or liquid sealing on the process connections.

2. Please ensure that the piping is clean and purged before you connect the ﬂow meter.

3. The gas used must be clean and dry.

4. For particle protection, we recommend to install our 50µm ﬁlter at the inlet.

5. It is recommended that the user checks the device on a regular schedule to ensure that it is leak free as both metal and elastomeric seals,

gaskets, O-rings and valve seats may change with age, exposure to process gas.

Note Your Sierra sales representative can help you to source suitable O-rings, elastomeric seals, ﬁttings and ﬁlters.

6. Please refer to the RedySmart Instruction Manual for detailed instruction on mounting orientation and location.

7. Please verify a proper electrical connection. The device must be grounded. The supply voltage is 18-30 vdc (typically ±50 mV).

Note The current consumption depends on the instrument version. Please refer to the information in the Instruction Manual.

This Quick Start Guide for the RedySmart Series Thermal Mass Flow

Meters and Controllers gives easy set up and installation instructions.

For complete instructions, please download and read the RedySmart

Series Instruction Manual. Before installing meter, follow the steps below.

Step 1. Download Instruction Manual

To get technical information, download the RedySmart Series

Instruction Manual at sierrainstruments.com/redysmart-manual

Step 2. Download FREE Software

Download the most current RedySmart product software at

sierrainstruments.com/redysmart-software. Use the included cable

(if ordered) to connect the meter to your computer.

IMPORTANT! If you do not have an internet connection, you must

download the software to a USB stick or other storage device.

Default Factory Settings

Modbus RTU

Communication speed 9600 Baud

Data bits 8

Stop bits 2

Parity None

Node address 247

Proﬁbus (optional)

Node address 125

When using several devices simultaneously the user has to

conﬁgure each device with an individual address!

Proﬁnet / EtherCAT (optional)

Name RedySmart SIP

IP address 0.0.0.0

Further information on the device conﬁguration can be found in the

Instruction Manual.

2 | RedySmart_v1_2020

Sub D Plug Pin Assignments Modbus RTU, Power Supply & Analog Signals (Male)

PIN Assignment Description

1Common (-) GND analog signals

2 Supply 0 Vdc 0 vdc supply voltage

3Supply +24 Vdc +24 vdc supply voltage

4Output (+) Analog output, measured value

5Setpoint (+) Analog input, setpoint

6Tx+ RS-485 Output (Y)

7Tx- RS-485 Output (Z)

8 Rx- RS-485 Input (B)

9Rx+ RS-485 Input (A)

Sub D Plug Pin Assignments Proﬁbus (Female)

PIN Assignment Description

1Not connected _

2Not connected _

3RxD/TxD-P Data transmit / receive; data wire B

4CNTR-P Repeater control signal (RTS)

5DGND Ground for data signals and VP

6 VP / +5V Power supply +5V

7Not connected _

8RxD/TxD-N Data transmit / receive; data wire A

9Not connected _

Rj45 Socket Pin Assignments Proﬁnet / Ethercat (Female)

PIN Assignment Wire Color

1Data (Tx+) Yellow

2 Data (Tx-) Orange

3Data (Rx+) White

4Not connected _

5Not connected _

6 Data (Rx-) Blue

7Not connected _

8Not connected _

Pin Assignment

All connection diagrams can be found in the Instruction Manual. Please also refer to the additional Digital

Communication Instruction Manual.

Warning! Always disconnect the power supply before working on the plugs.

3 | RedySmart_v1_2020

LED Operating Status

Power: The green LED lights up when the unit is supplied with the correct power supply voltage and is ready for operation.

TxRx : The yellow LED ﬂashes when the device is communicating on the digital Modbus RTU interface.

Alarm: If the red LED ﬂashes, there is a malfunction. If the LED is lit continuously, there may be a serious problem.

Disconnect the supply voltage and reconnect the device. If the LED is still lit, the unit must be returned for repair.

Power

Tx Rx

Alarm

Note The EtherCat/Proﬁnet devices have an extended LED operating status. Please refer to the Instruction Manual.

COM

PWR

ALM

Toxic, Flammable Gases and ATEX

Warning! In the case of toxic and ﬂammable gases, the respective safety guidelines in each country must be followed.

The RedySmart devices are not approved for use in Ex-zones. In the case of ﬂammable and toxic gases, ﬁttings and pipes

intended for that purpose must be used. The responsibility for safe operation lies with the designer of the facilities. The

devices must not be used for explosive mixtures (ATEX, detonating gas, consisting of O2and H2).

Limited Warranty Policy – Register Online

All Sierra products are warranted to be free from defects in material and workmanship and will be repaired or replaced at no charge to Buyer,

provided return or rejection of product is made within a reasonable period but no longer than three (3) years for calibration and non-calibration

defects, from date of delivery.

To assure warranty service, customers must register their products online on Sierra’s website. Online registration at of all of your

Sierra products is required for our warranty process. Read complete warranty policy at sierrainstruments.com/warranty.

Note: Please dispose of the device in an environmentally friendly way (recycle).

5 Harris Court, Building L / Monterey, CA 93940 / USA

USA: 800.866.0200 / 831.373.0200

Europe: +31.72.5071400

China: +8621 5879 8522

Email: techsupport@sierrainstruments.com or [email protected]

For global locations, visit: sierrainstruments.com/locations

www.sierrainstruments.com

CONTACT SIERRA

4 | RedySmart_v1_2020 99-2173

We Understand Flow is Tough.

We can solve this together.

sierrainstruments.com/RedySmart

Otros manuales de Instrumento de medición de Sierra

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Accu-Mass 730 Manual de usuario

Sierra

Sierra TM500 Manual de usuario

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra HART 600 Series Manual de usuario

Sierra

Sierra Innova-Flo 220 Series Manual de usuario

Sierra

Sierra InnovaMass i Series Manual de usuario

Sierra

Sierra 830 Series Manual de usuario

Sierra

Sierra FastFlo 620S Manual de usuario

Sierra

Sierra InnovaMass 240i Series Manual de usuario

Sierra

Sierra QuadraTherm 640i Series Manual de usuario

Sierra

Sierra Innova-Sonic Portable 210 Series Manual de usuario

Sierra

Sierra Smart-Trak IM-100 Series Manual de usuario

Sierra

Sierra BioTrak 645S Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra InnovaSonic 210 Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra InnovaMass 240i Series Manual de usuario

Sierra

Sierra Top-Trak 820 Series Manual de usuario

Sierra

Sierra Smart-Trak 100 series Manual de usuario

Sierra

Sierra Fast-Flo 620S Series Manual de usuario

Sierra

Sierra RedyIndustrial Series Manual de usuario

Sierra

Sierra Innova-Sonic 205 Manual de usuario

Sierra

Sierra Foundation Fieldbus 600 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario