Siemens FS-DACT Manual de usuario
Siemens Industry, Inc. Siemens Canada Limited
Building Technologies Division Building Technologies Division
Florham Park, NJ 2 Kenview Boulevard
Brampton, Ontario L6T 5E4 Canada
P/N 315-699464-10 (v10-21-10)
INSTALLATION INSTRUCTIONS
Model FS-DACT
Serial Digital Alarm Communicator Transmitter (DACT)
The FS-DACT Digital Alarm Communicator Transmitter Board is an optional module for the FS-250 and
FS-250C Fire Alarm System Control Panels. The FS-DACT provides telephone line connections for
communication with a DACR (Digital Alarm Communicator Receiver). The FS-DACT Board is mounted
on the Main Board. The FS-DACT Board options are set through the control panel programming
sequence.
PARTS SUPPLIED
1 FS-DACT Board
4 Spacers, 1”
1 Keps Nut, #6-32
1 Instruction Sheet
FS-DACT MOUNTING for FS-250 OR FS-250C
Step 1.) Installation is to be done by qualified personnel
who have thoroughly read and understood this
instruction sheet.
Step 2.) Disconnect BATTERY and AC prior to working on
equipment.
Step 3.) Mount DACT Board as shown, using four spacers
to the Main Board.
NOTE: Check to see that the header and
connectors are mated properly.
Step 4.) Attach ground wire as shown, using the nearest
main board mounting screw as shown.
Step 5.) Attach conduit and run wires as required.
Step 6.) Connect wires to the fire alarm system control unit
as required.
Step 7.) Apply power to system.
Step 8.) Program for proper operation of functions.
a) Tech Level>>Outputs>Option Mods>DACT CFG
(Set DACT line and general configurations)
b) Tech Level>>Outputs>Option Mods>DACT ACCTS
(Set DACT account configurations)
c) Maint Level>>Disable/Enable>Outputs>DACT
>Enabled
NOTE: See Programmer’s Manual (P/N 315-
049403[C]) for more details on programming.
Step 9.) Check for proper operation of functions.
P/N 315-699464-10 2
FS-DACT WIRING
NOTE: The RJ31X provides a convenient connection allowing the DACT to be installed and removed without requiring re-wiring and
can be installed by the telephone installer.
NOTE: If installed in Canada, the signal receiving centre must not share a common communication channel with the protected
premises. A dedicated line must be installed for use only by the FS-DACT.
FS-DACT FORMAT DESCRIPTION
Format Description
SIA DCS 8 Security Industry Association - Digital Communications Standard. Format may send up to eight events a call.
SIA 1997 Level Ia compatibility with support for O (old) blocks and 300 Baud (FAST) operation.
Sends an account number (up to 6 digits), a 2 character code and 3-digit identifier up to four times with FSK
frequency encoding.
SIA DCS 20 See SIA DCS 8, except format may send up to twenty events a call.
Ademco Contact ID Sends a 4-digit account number, a 3-digit code and 3-digit identifier up to four rounds of dual tone multiple
frequency with 1400 and 2300 Hz handshake frequency.
3/1 1400HZ Sends a 3-digit account number and a 1-digit code up to four rounds at 20 pps with 1400 Hz handshake
frequency.
3/1 2300HZ Sends a 3-digit account number and a 1-digit code up to four rounds at 20 pps with 2300 Hz handshake
frequency.
4/2 1400HZ Sends a 4-digit account number and a 2-digit code up to four rounds at 20 pps with 1400 Hz handshake
frequency.
4/2 2300HZ Sends a 4-digit account number and a 2-digit code up to four rounds at 20 pps with 2300 Hz handshake
frequency.
COMPATIBLE RECEIVERS/FORMATS
Receiver
Manufacturer Compatible
Receivers SIA DCS
8 SIA DCS
20 Ademco
Contact ID 3/1
1400HZ 3/1
2300HZ 4/2
1400HZ 4/2
2300HZ
Osborne-Hoffman,
Inc. QUICKALERT!
Model II Ademco
Contact ID Fast 3+1
1400HZ Fast 3+1
2300HZ Fast 4+2
1400HZ Fast 4+2
2300HZ
Osborne-Hoffman,
Inc. OH2000 SIA 1 SIA 1 Ademco
Contact ID Fast 3+1
1400HZ Fast 3+1
2300HZ Fast 4+2
1400HZ Fast 4+2
2300HZ
Radionics, Inc. D6500 3x1 3x1 4x2 4x2
Silent Knight Security
Corp. 9000 SIA 8 SIA 20 SK 3/1 SK 3/1 SK 4+2 SK 4+2
Silent Knight Security
Corp. 9500 SIA DCS SIA DCS Ademco
Contact ID SK 3/1 SK 3/1 SK 4+2 SK 4+2
Silent Knight Security
Corp. 9800 SIA DCS SIA DCS Ademco
Contact ID SK 3/1 SK 3/1 SK 4+2 SK 4+2
Telephone Line Connection Ratings:
Power Limited
Supervised
Voltage: 24VDC nominal, 0.054A max.
Ringer Equivalence: 0.4B
Telephone Line #1
Connection from TELCO
Optional Output to telephone
(Note: The DACT may seize
the line to report events)
Telephone Line #2
Connection from TELCO
Optional Output to telephone
(Note: The DACT may seize
the line to report events)
8-PIN
MODULAR
PLUG
8-PIN
MODULAR
PLUG
RED
GREEN
GREY
BROWN
RED
GREEN
GREY
BROWN
RJ31X
JACK
RJ31X
JACK
TIP
RING
TIP
RING
TIP
RING
TIP
RING
P/N 315-699464-10 3
FS-DACT EVENT CODES
Event Type SIA DCS
(8 or 20)*Ademco
Contact ID**
3/1
1400 Hz or
2300HZ
4/2
1400 Hz or
2300HZ
Fire Point Alarm FA tuvw 1 110 xyz 0 01
Fire Point Alarm Restore
(Through Reset)
FH tuvw 3 110 xyz 2 21
Waterflow Point Alarm SA tuvw 1 113 xyz 0 02
Waterflow Point Restore SH tuvw 3 113 xyz 2 22
General Alarm FA 298 1 110 298 0 01
Supervisory Point Active SS tuvw 1 203 xyz 6 66
Supervisory Point Restore SR tuvw 3 203 xyz 7 76
AC Trouble AT 0 1 301 000 8 80
AC Trouble Restore AR 0 3 301 000 7 70
Power Up/Reset RR 0 3 305 000 7 70
Fire Point Trouble FT tuvw 1 373 xyz 8 83
Fire Point Trouble Restore FJ tuvw 3 373 xyz 7 73
Fire Trouble Restore (All Clear) FJ 9 3 373 009 7 79
Fire Point Device Bypass (Disable) FB tuvw 1 571 xyz 8 84
Group, Zone or Panel Relay Bypass
(Disable) FB 298 1 571 298 8 84
Releasing Circuits Bypassed (Disable) SS 298 1 203 298 6 66
Releasing Circuits Unbypassed (Enable) SR 298 3 203 298 7 76
Fire Point Device Unbypass (ReEnable) FU tuvw 3 571 xyz 7 74
Group, Zone or Panel Relay Unbypass
(ReEnable) FU 298 3 571 298 7 74
NAC Bypass (Disable) FB 2nn 1 571 4nn 8 84
NAC Unbypass (ReEnable) FU 2nn 3 571 4nn 7 74
System Battery Trouble YT 298 1 302 298 8 87
System Battery Trouble Restore YR 298 3 302 298 7 77
NAC Circuit nn Trouble FT 2nn 1 373 4nn 8 83
NAC Circuit nn Trouble Restore FJ 2nn 3 373 4nn 7 73
NAC Circuit Ground Fault FT 299 1 373 299 8 89
NAC Circuit Ground Fault Restore FJ 299 3 373 299 7 73
FDLC Ground Fault Trouble FT 299 1 373 299 8 83
FDLC Ground Fault Trouble Restore FJ 299 3 373 299 7 73
FDLC Trouble FT 30d 1 373 298 8 83
Phone Line 1 Trouble LT 1 1 351 001 8 81
Phone Line 1 Trouble Restore LR 1 3 351 001 7 71
Phone Line 2 Trouble LT 2 1 352 002 8 82
Phone Line 2 Trouble Restore LR 2 3 352 002 7 72
Dialer Data Lost RT 30 1 354 030 8 88
Fire Test (Drill) begin FI 0 1 604 000 9 90
Fire Test (Drill) end FK 0 3 604 000 9 92
Quick Test Begin FT 298 1 373 298 8 83
Quick Test Stop FJ 298 3 373 298 7 73
System Trouble qrs FT qrs 1 373 qrs 8 83
System Trouble qrs Restore FJ qrs 3 373 qrs 7 73
Auto Test – System Normal RP 30 1 602 030 9 93
Manual Test – System Normal*** TX 30 1 601 030 9 99
Point Active in Quick Test FX tuvw 1 604 xyz 9 91
***
Note: Below Panel Firmware revision 6.3, this code is always paired with the Auto Test Code (RP 30, etc.) during the daily automatic test.
nn denotes NAC circuit number 1-12.
ddenotes FDLC number.
Important: Account 1 and Account 2 must be set for the same reporting format. See the FS-250 Programming
Manual, P/N 315-049403, or the FS-250C Programming Manual, P/N 315-049403C, as applicable, for details on
setting the reporting format.
P/N 315-699464-10 4
SIA / ADEMCO
SYSTEM TROUBLE CODES
Trouble Type q r s
Network Trouble 2 9 0
DACT General Trouble 2 9 1
DACT Account 1 2 9 2
DACT Account 2 2 9 3
General Trouble 2 9 8
FCC Requirements - Part 68
This equipment complies with Part 68 of the Federal Communication Commission (FCC) Rules and Regulations. On
the bottom is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence
Number (REN) for this equipment. If requested, this information must be provided to the telephone company.
FCC Registration Number: ABK USA-34988-AL-E
USOC telephone jack: RJ31X
Ringer Equivalence Number (REN):0.4B
The REN is useful to determine the quantity of devices which may connect to the telephone line. Excessive REN’s on
the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the
sum of the REN’s should not exceed five (5.0). To be certain of the number of devices that may be connected to the line,
as determined by the total REN’s, contact the telephone company to determine the maximum REN for the calling area.
If the FS-DACT equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company
will notify you of the discontinuance as soon as possible. Also, you will be advised of your right to file a complaint with
the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of your telephone equipment. If this happens, the telephone company will provide advance notice so that
you can modify your equipment as required to maintain uninterrupted service.
If you experience trouble with the FS-DACT Board for repair and/or warranty information please contact an authorized
Siemens Fire Safety representative.
If the trouble is causing harm to the telephone network, the telephone company may request you disconnect to
equipment from the network until the problem is solved. You should not attempt to repair this equipment yourself. This
equipment contains no customer or user serviceable parts.
This device may not be used on public coin or party line services.
Changes or modifications not expressly approved by Siemens Fire Safety could void your authority to operate this
equipment.
SIA DCS
*EVENT CODE IDENTIFIER DESCRIPTIONS
4 Digit Code t u v w
Device Address Loop (1-4) Address (001-252)
ADEMCO CONTACT ID
**EVENT CODE IDENTIFIER DESCRIPTIONS
x y z
Input Group # Address (001 – 240)
Otros manuales de Transmisor de Siemens
Siemens
Siemens Sitrans LR250 Manual de usuario
Siemens
Siemens SITRANS L Series Manual de usuario
Siemens
Siemens Sitrans LR200 Manual de instrucciones
Siemens
Siemens SITRANS P LH300 Guía del administrador
Siemens
Siemens Sitrans LR250 Guía del administrador
Siemens
Siemens Sitrans LR250 Guía del administrador
Siemens
Siemens SITRANS LR560 Manual de usuario
Siemens
Siemens SITRANS L Series Manual de usuario
Siemens
Siemens SITRANS L Series Guía del administrador
Siemens
Siemens SITRANS L Series Guía del administrador
Siemens
Siemens Sitrans LR200 Guía del administrador
Siemens
Siemens Sitrans LR250 Manual de usuario
Siemens
Siemens REV23.03RF Manual de usuario
Siemens
Siemens US-100-1 Manual de usuario
Siemens
Siemens DS III PROFIsafe Series Manual de usuario
Siemens
Siemens THE PROBE Manual de usuario
Siemens
Siemens SITRANS LR25 Manual de instrucciones
Siemens
Siemens SITRANS LR560 Manual de usuario
Siemens
Siemens sitrans tr200 Manual de usuario
Siemens
Siemens Sitrans LR200 Manual de usuario
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
