Siemens D2325CPS Manual de usuario

P/N 315-050019-6

Installation Instructions

Model D2325CPS

Single Mode (1310nm) Fiber Optic Interface

INTRODUCTION

The Model D2325CPS from Siemens Industry, Inc. (See

Figure 1) is a Fiber Optic interface for the MXL’s RS-485

network (MNET or XNET), FireFinder XLS/Desigo Fire

Safety Modular/Cerberus PRO Modular network

(HNET or XNET) and HUB-4 FSI. It uses a two-fiber

(duplex) pair between each device. The D2325CPS can

function as either a repeater or an end point unit.

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA-2

+ DATA -1

Figure 1

D2325CPS Module

The D2325CPS can operate in either a daisy chain

(See Figure 2) or star configuration (See Figure 3).

This allows for network configurations that are not

possible with the RS-485 network alone.

WARNING:

The D2325CPS module is not listed for use by

Factory Mutual. Applications requiring fiber con-

nectivity of voice modules/systems are therefore

not Factory Mutual listed.

WARNING:

Do not use the D2325CPS with CXL Systems.

MOUNTING

The D2325CPS has four keyhole slots for #6 screws.

Mount the device in the locations listed below using

the four #6 screws provided.

A bracket (P/N 500-692880) is available for mounting

the D2325CPS in any MXL enclosure that will accept

a MOM-4 (See Figure 4). This bracket has the same

footprint as the MOM-4 and accommodates two

D2325CPS modules. An assembly kit is included with

the bracket that contains four nuts and eight screws.

Mount the bracket in the enclosure with the four nuts

at the positions labeled X(See Figure 4). Start four of

the 6-32 screws and slip the keyhole slots in the

D2325CPS

over them. Tighten the four screws.

System 3 style rails that mount on an MBR-2 or MME-3

backbox (P/N MSR-1) are also available and can be

used for mounting the D2325CPS with the System 3

MPFO Bracket. Up to three brackets can be installed on

a single rail.

A bracket, Model D2300-MP, is available for mounting

two D2325CPS modules in any FireFinder XLS/

Desigo Fire Safety Modular/Cerberus PRO Modular

CAB enclosure. The D2300-MP fits in the same

footprint as a CC-5 and mounts to the CAB-MP. A

hardware kit is provided for attaching the D2300-MP to

the CAB-MP and mounting two D2325CPS modules

onto the D2300-MP. Mount the D2325CPS modules

prior to installing the D2300-MP onto the CAB-MP.

Note that when using two D2325CPS modules, the

center two mounting holes on each D2325CPS share

the two center studs on the D2300-MP (See Figure 5).

ELECTRICAL CONNECTIONS

POWER INPUT

The D2325CPS uses filtered or unfiltered 24 VDC.

The D2325CPS can only be powered from the

sources listed in Table 1 on page 6.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Canada, Ltd.

1577 North Service Road East

Oakville, Ontario

L6H 0H6 Canada

Figure 2

Daisy Chain Configuration (MNET Shown)

SINGLE MODE DUPLEX OPTICAL FIBER

POWER BUDGET - MAX LOSS

-11 dB 9/125 FIBER

SINGLE MODE DUPLEX OPTICAL FIBER

POWER BUDGET - MAX LOSS

-11 dB 9/125 FIBER

CONNECTION

RS-485

32 NODES MAX

SUPERVISED

RS-485

32 NODES MAX

SUPERVISED

RS-485

32 NODES MAX

SUPERVISED

DATA

XTM

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

SUPERVISED

EOLR

120 OHMS, 1/4W

P/N 140-820150

EOLR

120 OHMS, 1/4W

P/N 140-820150

EOLR

120 OHMS, 1/4W

P/N 140-820150

EOLR

120 OHMS, 1/4W

P/N 140-820150

USE THE 120 ¼ W, 5%

EOL RESISTOR ASSEMBLY,

AS APPLICABLE:

P/N 140-820150 (MMB-1/-2)

OR P/N 140-049099 (MMB-3)

RCC-1

PSR-1

MMB

EOLR

120 OHMS, 1/4W

P/N 140-820150

PSR-1

Figure 3

Star Configuration (MNET Shown)

DATAPXTMR

POWER

DATAPREC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

DATA

XTMR

DATA

XTM

POWER

DATA

REC

DATA

REC

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

PSR-1

EOLR

120 OHMS, 1/4W

P/N 140-820150

PSR-1

RS-485

32 NODES MAX

SUPERVISED

CONNECTION

SUPERVISED

TO ADDITIONAL

D2325CPS

MODULES

SINGLE MODE DUPLEX OPTICAL FIBER

POWER BUDGET - MAX LOSS

-11 dB 9/125 FIBER

USE THE 120 ¼ W, 5%

EOL RESISTOR ASSEMBLY,

AS APPLICABLE:

P/N 140-820150 (MMB-1/-2)

OR P/N 140-049099 (MMB-3)

MMB

Figure 4

Mounting the D2325CPS in an MBR-2 or MME-3 Backbox

Figure 5

Mounting the D2325CPS in a CAB-1 Backbox

WARNING

DISCONNECT POWER

PRIOR TO

REMOVING

TERMINAL

BLOCK PROTECTION

OMM-1

P/N 500-692880

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2325CPS

BRACKET

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

D2325CPS

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

HNET

HUNDREDS

ONES

TENS

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

DATA

XTMR

DATA

XTMR

POWER

DATA

REC

DATA

REC

D2300-MP

D2325CPS D2325CPS

CAB-1

XNET FAIL

XNET

STYLE 7

ENABLED

CAN

ACTIVE NETWORKS

HNET/XNET STYLE

GROUND FAULT

NETWORK

PORT

LOOP B FAIL

GND FAULT

LOOP A FAIL

STYLE 4

DISABLED

HNET

CARD FAIL

HNET FAIL

CAN FAIL

RESET

POWER

NIC-C

ALARM

CLASS A OPEN

CLASS A RETURN

CLASS A OPEN

TROUBLE

ZONES STATUS

SHORT

CARD FAIL

GND FAULT

HNET FAIL

RESET

POWER

DLC

GND FAULT

24V 12A FAIL

24V 4A FAIL

MODULE FAIL

HNET FAIL

CAN FAIL

RESET

POWER

PSC-12

TB1

TB3

BATTERY

OFF

O—

FIBER OPTIC CABLE POWER LIMITED HNET/XNET

ROUTE AS SHOWN

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

POWER +24 VDC -1

-2

(DO NOT USE) -4

(DO NOT USE) -3

-DATA -2

+DATA -1

HNET

HUNDREDS

ONES

TENS

HNET

HUNDREDS

ONES

TENS

TB2

GND

P12

TB4

Figure 6

Wiring the D2325CPS as both a Repeater and End Point Unit

D2325CPS

SUPERVISED

POWER BUDGET - MAX LOSS

- 11 dB 9/125 FIBER

N.C.

END POINT

RS-485 NETWORK

MNET/HNET/XNET

(SEE FIGURES 7, 8 & 9)

FACP

REPEATER

SUPERVISED

POWER BUDGET - MAX LOSS

- 11 dB 9/125 FIBER

END POINT

N.C.

DATA

REC

DATA

XTMR

DATA

REC

DATA

XTMR

DATA

REC

DATA

XTMR

DATA

REC

DATA

XTMR

DATA

REC

DATA

XTMR

DATA

REC

DATA

XTMR

Figure 7

Wiring the RS-485 MNET Network in Style 4 and Style 7

MOM-4

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

EOLR

120 OHMS, 1/4W

P/N 140-820150

EOLR

120 OHMS, 1/4W

P/N 140-820150

NET-7

REFER TO NET-7

INSTALLATION INSTRUCTIONS

P/N 315-091914

1234

TB1

STYLE 7 MNET

EOLR

120 OHMS, 1/4W

P/N 140-820150

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

SUPERVISED

MMB

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

TB1

(DO NOT USE)

STYLE 4 MNET

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

SUPERVISED

USE THE 120 ¼ W, 5%

EOL RESISTOR ASSEMBLY,

AS APPLICABLE:

P/N 140-820150 (MMB-1/-2)

OR P/N 140-049099 (MMB-3)

For non-power limited wiring, the PLM-35 (Installation

Instructions P/N 315-093495) must be used to comply

with NFPA 70 per NEC 760. All wiring must be in

accordance with Article 760 of NEC or local building

codes.

For additional information on the MXL/MXLV System,

refer to the MXL/MXLV Manual, P/N 315-092036.

24 VDC CURRENT CALCULATION (MXL ONLY)

The 24 VDC output ratings for the MMB/SMB and PSR-1 are:

MMB-2/-3 6A at 24 VDC (MPS-6); 12A at 24 VDC (MPS-12)

SMB-2 6A at 24 VDC (MPS-6); 12A at 24 VDC (MPS-12)

PSR-1 6A at 24 VDC (MPS-6); 12A at 24 VDC (MPS-12)

The following modules all draw current from the 24 VDC supply. Add the value for each module that is installed in

the enclosure where the D2325CPS is to be installed. Be sure to include the D2325CPS in this calculation.

ELUDOM

CDV42EVITCA ELUDOM TNERRUCYTITNAUQLATOT

1-MCAAm58

1-CSAAm14

2-CSAAm16

003-IMCAm0

4-MRCAm57

4-MSC xamA5.1+Am43 ti

ucricrep

4-MZC Am027 mralanisenoz4

SPC5232DAm26

4-/2-BKMAm0

4-TENAm0

7-TENAm0

M7-TENAm0

7-IOMAm021

61-DOMxamAm058

61-DI

MxamAm23

1-MIPAm0

1-CTBAm44

1-MCRAm031

03-CAZW03taA3

1-CCOAm71

B8-1CZAm071

B8-2CZAm243

BA4-2CZAm761

BA4-3CZAm861

B8-TCZAm8

LATOT

1elbaT

METSYSECRUOSREWOP

LXM21-95BT;5-41BT:2-BMM 21-95BT;-,+9BT:3-BMM 6-3;2-13BT:1-RSP

redniFeriF ogiseD/SLX ytefaSe

riF -ebreC/raludoM ORPsur raludoM

-,+4BT:21-CSP -,+4BT:21-XSP

ECRUOSREWOP 4-DAP/3-DAP-,+XUA

53-SP6-51BT

EOLR

120 OHMS, 1/4W

P/N 140-820150

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

1234

EOLR

120 OHMS, 1/4W

P/N 140-820150

EOLR

120 OHMS, 1/4W

P/N 140-820150

OMIT THIS EQUIPMENT FOR STYLE 4 XNET

REFER TO NIM-1R OR NIM-1W

INSTALLATION INSTRUCTIONS

P/N 315-092953 OR P/N 315-099165,

AS APPLICABLE

TB3

NIM-1R/-1W

MOM-4

D2325CPS*

D2325CPS

-4

-3

-2

-1

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

(DO NOT USE)

-DATA

+DATA

SUPERVISED

tnerruCeludoMCDV42evitcAAm26

tnerruCeludoMCDV42ybdnatSAm26

Figure 8

Wiring the RS-485 XNET Network

in Style 4 and Style 7 (MXL)

RS-485 NETWORK

The RS-485 MNET, XNET and HNET networks

connect to the D2325CPS on the terminal block with

the markings +DATA (1) and -DATA(2). Terminals 3

and 4 are not used. For Style 4 networks one

D2325CPS is needed at each Fiber Optic drop. For

Style 7 networks two D2325CPS modules are needed

at each drop.End of line devices are required on each

RS-485 pair in the system. Install them at the extreme

ends of each pair. Refer to Figures 7 and 8 (MXL)

and Figure 9 (FireFinder XLS/Desigo Fire Safety

Modular/Cerberus PRO Modular) for wiring instruc-

tions and ratings for both Style 4 and Style 7.

NOTE: Positive and negative ground fault detected

when terminals shorted to earth.

FIBER CONNECTIONS

The D2325CPS can function as both a repeater and an

end point unit. When used as an end point, connect

to the fiber connectors labeled A. Make no connec-

tion to the Bconnectors. In the repeater mode, use

both pairs of connectors, Aand B.

Two Fiber Optic cables are required between each pair

of D2325CPS modules. Use a high quality duplex Fiber

Optic cable containing 9/125 fiber. Duplex fiber optic

cable has two cables in a single shield similar to

electrical zip cord. Use ST style fiber connectors.

Please contact the fiber manufacturer regarding

instructions for terminating the fiber.

When installing the fiber pairs, each fiber must

connect between the transmit data (DATA XTMR) on

one D2325CPS and the receive data line (DATA REC)

on the other D2325CPS.

The D2325CPS fiber connection is classified as Style

DCLB and Style DCLA per ULC-527.

INDICATORS

The D2325CPS has five LED indicators for Power

and Status.

The LEDs are located on the side of the module with

the Fiber Optic connectors. The Power LED is green

and lights whenever there is 24 VDC. Both channels A

and Bhave a yellow and green LED. The green LED

indicates that the D2325CPS is transmitting data on that

channel. The yellow LED lights when data is received.

ELECTRICAL RATINGS

Input Power 18-31 VDC, 62mA max

Battery Power 24 VDC, 62mA max

RS-485 8V (P-P), 150mA max

Figure 9

Wiring the RS-485 HNET or XNET Network in Style 4 and Style 7

(FireFinder XLS/Desigo Fire Safety Modular/Cerberus PRO Modular)

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

EOLR

120 OHMS, 1/4W

P/N 140-820150

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

NO EOLR REQUIRED AT THE NIC-C

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

NO EOLR REQUIRED AT THE NIC-C

STYLE 4 XNET

STYLE 7 XNET

12345678

910111213141516

17 18 19 20 21 22 23 24

DO NOT USE

DO NOT USE DO NOT USE

ONE SLOT OF CC-5/CC-2

NIC-C

SUPERVISED

12345678

910111213141516

17 18 19 20 21 22 23 24

DO NOT USE

ONE SLOT OF CC-5/CC-2

NIC-C

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

EOLR

120 OHMS, 1/4W

P/N 140-820150

SUPERVISED

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

Figure 10

Wiring the RS-485 HNET and XNET Network Style 4 and Style 7

(FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular)

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

EOLR

120 OHMS, 1/4W

P/N 140-820150

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

RS-485 RATINGS:

8V P-P

150mA MAX

80 OHMS MAX

18 AWG MIN

STYLE 4 RS-485 HUB-4 FSI

STYLE 7 RS-485 HUB-4 FSI

12345678

910111213141516

17 18 19 20 21 22 23 24

ONE SLOT OF CC-5/CC-2

HUB-4

SUPERVISED

12345678

910111213141516

17 18 19 20 21 22 23 24

PORT 2

ONE SLOT OF CC-5/CC-2

HUB-4

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA

EOLR

120 OHMS, 1/4W

P/N 140-820150

SUPERVISED

D2325CPS

-4

-3

-2

-1

(DO NOT USE)

-DATA

+DATA PORT 1

-A

A+

B-

A+

B-

RS-485

INTERFACE

Port #3 RS-485

INTERFACE

Port #4

RS-485

INTERFACE

Port #3 RS-485

INTERFACE

Port #4

RS-485

INTERFACE

Port #2x

A+

B-

A+

B-

RS-485

INTERFACE

Port #2x

EOLR

120 OHMS, 1/4W

P/N 140-820150

MODEM OR

20 FT IN CONDUIT

20 FT IN

CONDUIT

P/N 315-050019-6 Document ID A6V10244656

Cyber security disclaimer

Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety,

security management and physical security systems. The security functions on these products and solutions are impor-

tant components of a comprehensive security concept.

It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept that is custom-

ized to individual security needs. Such a security concept may result in additional site-specific preventive action to

ensure that the building comfort, fire safety, security management or physical security system for your site are operated

in a secure manner. These measures may include, but are not limited to, separating networks, physically protecting

system components, user awareness programs, defense in depth, etc.

For additional information on building technology security and our offerings, contact your Siemens sales or project

department. We strongly recommend customers to follow our security advisories, which provide information on the

latest security threats, patches and other mitigation measures.

http://www.siemens.com/cert/en/cert-security-advisories.htm

Tabla de contenidos

Otros manuales de Equipo de grabación de Siemens

Siemens

Siemens XTRI-S Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens WW8000 MP4.70 Manual de usuario

Siemens

Siemens SIMATIC HMI Mobile Panel 277 RO Manual de usuario

Siemens

Siemens 6AT8000-1BB00-0XA0 Manual de usuario

Siemens

Siemens Albatros2 RVA78.690 Manual de usuario

Siemens

Siemens CIM Manual de usuario

Siemens

Siemens PMI Manual de usuario

Siemens

Siemens MTP700 Unified Comfort Manual de usuario

Siemens

Siemens 3RX9501-1BA00 Manual de usuario

Siemens

Siemens WEBUI Manual de usuario

Siemens

Siemens 538-735 Manual de usuario

Siemens

Siemens RUGGEDCOM RMC30 Manual de usuario

Siemens

Siemens SINAMICS V90 Manual de usuario

Siemens

Siemens SINAMICS V90 Manual de usuario

Siemens

Siemens Apogee P1 Manual de usuario

Siemens

Siemens SEZ50MB Manual del operador

Siemens

Siemens SIMATIC HMI KTP700F Mobile Manual de usuario

Siemens

Siemens SIMATIC Distributed I/O System DP/ASi Link Manual de usuario

Siemens

Siemens SIMATIC HMI KP400 Comfort Manual de usuario

Siemens

Siemens AEK84 Manual de usuario

Siemens

Siemens N148/22 Manual de servicio

Siemens

Siemens N148/23 Manual de usuario

Siemens

Siemens simatic ET 200MP Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado