Siemens SLI-5310 Manual de usuario

SLI-5310/SLI-5310-I IAD

User’s Manual

Rev: 1.3

2007/03/30

No part of this publication may be reproduced in any form by any means without the prior written permission.

Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective

companies.

ADSL Router User Manual

by any means, electronic or mechanical, for any purpose, without the express written permission of

the seller.

Information in this document is subject to change without notice. The statements, configurations,

technical data, and recommendations in this document are believed to be accurate and reliable, but

are presented without express or implied warranty. The seller therefore assumes no responsibility and

shall have no liability of any kind arising from the supply or use of this document or the material

contained herein.

In the interest of improving internal design, operational function, and/or reliability, the seller reserves

the right to make changes to the products described in this document without notice.

The seller does not assume any liability that may occur due to the use or application of the product(s)

or circuit layout(s) described herein.

In addition, the program and information contained herein are licensed only pursuant to a license

agreement that contains restrictions on use and disclosure (that may incorporate by reference certain

limitations and notices imposed by third parties).

All other product or service names mentioned in this document may be trademarks of the companies

with which they are associated.

For Installation Use only the type of power source indicated on the marking labels.

Use only power adapter supplied with the product.

Do not overload wall outlet or extension cords as this may increase the

risk of electric shock or fire. If the power cord is frayed, replace it with a

new one.

Proper ventilation is necessary to prevent the product overheating. Do

not block or cover the slots and openings on the device, which are

intended for ventilation and proper operation. It is recommended to

mount the product with a stack.

Do not place the product near any source of heat or expose it to direct

sunlight.

Do not expose the product to moisture. Never spill any liquid on the

product.

Do not attempt to connect with any computer accessory or electronic

product without instructions from qualified service personnel. This may

result in risk of electronic shock or fire.

Do not place this product on unstable stand or table.

For Using Power off and unplug this product from the wall outlet when it is not in

use or before cleaning. Pay attention to the temperature of the power

adapter. The temperature might be high.

After powering off the product, power on the product at least 15

seconds later.

Do not block the ventilating openings of this product.

When the product is expected to be not in use for a period of time,

unplug the power cord of the product to prevent it from the damage of

storm or sudden increases in rating.

For Service Do not attempt to disassemble or open covers of this unit by yourself. Nor

should you attempt to service the product yourself, which may void the user’s

authority to operate it. Contact qualified service personnel under the following

conditions:

If the power cord or plug is damaged or frayed.

If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product does not operate normally when the operating instructions

are followed.

If the product has been dropped or the cabinet has been damaged.

If the product exhibits a distinct change in performance.

Caution Any changes or modifications not expressly approved by the party

responsible for compliance could void the authority to operate

equipment.

iii

ADSL Router User Manual

This equipment must be installed and operated in accordance with provided

instructions and a minimum 20 cm spacing must be provided between computer

mounted antenna and person’s body (excluding extremities of hands, wrist and feet)

during wireless modes of operation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference;

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment can generate, use and radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

zReorient or relocate the receiving antenna.

zIncrease the separation between the equipment and receiver.

zConnect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

zConsult the dealer or an experienced radio/television technician for help

Before You Use

Thank you for choosing this IntegratedAccess Device. With the asymmetric

technology, this device runs over standard copper phone lines. In addition,ADSL

allows you to have both voice and data services in use simultaneously all over one

phone line.

SLI-5310/SLI-5310-I IAD is a DSL broadband access device which allowsADSL

connectivity while providing voice over IP function for home or office users. It

supportsADSL2/ADSL2+ and is backward compatible to ADSL, even offers

auto-negotiation capability for different flavors (G.dmt, G.lite, T1.413 Issue 2, or

ADSL2/ADSL2+) according to central office DSLAM’s settings (Digital Subscriber

Line Access Multiplexer). To benefit users’ access to the Internet, 4-port 10/100

Mbps Ethernet switch hub is equipped with this IAD. Also the feature-rich routing

functions are seamlessly integrated to ADSL service for existing corporate or home

users. Now users can enjoy various bandwidth-consuming applications via the

SLI-5310/ SLI-5310-I IAD.

Unpacking

Check the contents of the package against the pack contents checklist below. If any

of the items is missing, then contact the dealer from whom the equipment was

purchased.

9Integrated Access Device

9Power Adapter and Cord

9RJ-11 ADSL Line Cable

9RJ-45 Ethernet Cable

9USB Cable

9Phone Cable

9PSTN Cable

9Quick Start Guide

9Driver & Utility Software CD

Features

ADSL Compliance

³ANSI T1.413 Issue 2

³ITU G.992.1 Annex A (G.dmt)

³ITU G.992.2 Annex A (G.lite)

³ITU G.994.1 (G.hs)

³Support dying gasp

³Maximum Rate: 8 Mbps for downstream and 1 Mbps for upstream

ADSL Router User Manual

ADSL2 Compliance

³ITU G.992.3 Annex A (G.dmt.bis)

³Maximum Rate: 12 Mbps for downstream and 1 Mbps for upstream

ADSL2+ Compliance

³ITU G.992.5 Annex A

³Maximum Rate: 24 Mbps for downstream and 1.2 Mbps for upstream

Voice over IP Features

³Call Feature: basic outgoing and incoming call, Call Waiting, Three Party

Conference, Call Transfer, Caller ID

³Call Control: support MGCP (RFC2705) or SIP (RFC3261)

³Voice Transport: compliance to RTP (RFC1889)

³Voice Codec: G.711 (a-law and u-law), G.726, and G.729A

³Tone/Ring Signal: compliance to North America, UK, France, Netherlands,

Japan, and China

³Tone Generation: support dial tone, ring back tone, busy tone, ring tone, and

various tones on demand

³Tone Detection: support DTMF

³Echo Cancellation: compliance to G.168

³Support FAX/Analog Modem function

³Support T.38Fax relay1

³Support RFC2833 RTP Payload for DTMF Digits, Telephony Tones and

Telephony Signals

³Two VOIP (FXS) ports for VOIP phone calls

³Both VOIP ports supporting intelligent lifeline backup

³Manual selection of PSTN mode or VOIP mode while making a phone call

³Automatic selection of PSTN phone call on dialing the emergency calls

³Traffic flow control to guarantee voice quality

ATM Features

³Compliant to ATM Forum UNI 3.1 / 4.0 Permanent Virtual Circuits (PVCs)

³Support up to 16 PVCs for UBR, CBR, VBR-nrt, VBR-rt with traffic shaping

³RFC2684 LLC Encapsulation and VC Multiplexing overAAL5

³RFC2364 Point-to-Point Protocol (PPP) over AAL5

³RFC2225 Classical IP andARP overATM

³RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding) and

Client functions

³Support PPPoA or PPPoE Bridged mode (the IP address got from ISP can be

passed to the user’s PC and behave as the IP address of the user’s PC.)

1T.38 fax relay can be supported on demand.

Before You Use

³OAM F4/F5 End-to-End/Segment Loopback Cells

Bridging Features

³Supports self-learning bridge specified in IEEE 802.1d Transparent Bridging

³Supports up to 4096 learning MAC addresses

³Transparent Bridging among 10/100 Mb Ethernet and USB

³Supports IGMP Snooping

³Supports 802.1Q VLAN packet pass-through

Routing Features

³NAT (Network Address Translation) / PAT (Port Address Translation) let

multiple users on the LAN to access the internet for the cost of only one IP

address.

³ALGs (Application Level Gateways): such as NetMeeting, MSN Messenger,

FTP, Quick Time, mIRC, Real Player, CuSeeMe, VPN pass-through with

multiple sessions, etc.

³Port Forwarding: the users can setup multiple virtual servers (e.g., Web, FTP,

Mail servers) on user’s local network.

³Support DMZ

³UPnP IGD (Internet Gateway Device) with NAT traversal capability

³Static routes, RFC1058 RIPv1, RFC1723 RIPv2

³DNS Relay, Dynamic DNS

³DHCP Client/Relay/Server

³Time protocol can be used to get current time from network time server

³Support IGMP Proxy

³Support port mapping function which allows you to assign all data traffic

transmitted among specific Internet connections and LAN ports

³Support IP/Bridge QoS for prioritize the transmission of different traffic classes

³Support 802.1Q VLAN Tagging

Security Features

³PAP (RFC1334), CHAP (RFC1994), and MS-CHAP/MS-CHAP2 for PPP

session

³Firewall support IP packets filtering based on IP address/Port number/Protocol

type

³Bridge packet filtering (optional)

³URL filtering (optional)

³Support DoS (Deny of Services) which detect & protect a number of attacks

(such as SYN/FIN/RST Flood, Smurf, WinNuke, Echo Scan, Xmas Tree Scan,

etc)

Configuration and Management

³User-friendly embedded web configuration interface with password protection

³Remote management accesses control

³Telnet session for local or remote management

³Firmware upgrades through HTTP, TFTP, or FTP

vii

ADSL Router User Manual

³The boot loader contains very simple web page to allow the users to update the

run-time firmware image.

³Configuration file backup and restore

³SNMPv1/v2 agent with MIB-II, ADSL Line MIB

Subscription for ADSL Service

To use the IAD, you have to subscribe for ADSL service from your broadband

service provider. According to the service type you subscribe, you will get various IP

addresses:

Dynamic IP: If you apply for dial-up connection, you will be given an Internet

account with username and password. You will get a dynamic IP by dialing up to

your ISP, such as using PPPoA, PPPoE, or MER mode.

Static IP address: If you apply for full-time connectivity, you may get either one

static IP address or a range of IP addresses from your ISP. The IP address varies

according to different ADSL service provider, such as using IPoAor MER mode.

Notes and Cautions

Note and Caution in this manual are highlighted with graphics as below to indicate

important information.

Note Contains information that corresponds to a specific topic.

Caution Represents essential steps, actions, or messages that should not be

ignored.

viii

Chapter 1: Overview

This chapter provides you the description for the LEDs and connectors on the front

and rear surface of the router. Before you use/install this IAD, please take a look at

the information first.

Physical Outlook

Front Panel

The following illustration displays the front panel of this IAD:

LED Indicators

This IAD is equipped with several LEDs on the front panel as described in the table

below:

Function Color Definition

Off Power is off.

Solid Green Power is on and the device operates normally.

Power on self-test in progress

The device enters the console mode of the boot

loader.

Solid Red

Power

Power on self-test failure if the led always stays solid

red.

Flash Red Firmware upgrades in progress

Off No DSL signal is detected.

Slow Flash Green DSL line is handshaking in progress

Fast Flash Green DSL line is training in progress

DSL

Solid Green DSL line connection is up.

Off No PPPoA or PPPoE connection

PPP Solid Green At least one PPPoA or PPPoE connection is up. The

users can access the Internet now.

Off No Ethernet signal is detected.

Flash Green User data is going through Ethernet port

Ethernet Solid Green Ethernet interface is ready to work.

Off No USB signal is detected.

Flash Green User data is going through USB port

USB Solid Green USB interface is ready to work.

Off The phone is on-hook or in PSTN mode.

Phone 1 or 2 Solid Green VOIP phone call is in use.

Off Voice over IP service is not ready. The users can

make PSTN phone calls only.

VOIP Ready Solid Green Voice over IP service is ready.

ADSL Router User Manual

Rear Panel

The following figure illustrates the rear panel of your IAD:

Connector Description

Phone Phone set connector

PSTN PSTN connector

DSL RJ-11 connector

Ethernet 1 - 4 Ethernet 10/100 Base-T auto-sensing

USB USB connector (for model with USB interface only)

Power Switch

12VAC Power connector

Note: For use only with power supply OEM type AA-121A5BN,

Leader type A48120150-C5.

Tabla de contenidos

Otros manuales de Enrutador de red de Siemens

Siemens

Siemens RUGGEDCOM RSL910 Manual de usuario

Siemens

Siemens SCALANCE X-400 Guía del administrador

Siemens

Siemens C2-010 Manual de usuario

Siemens

Siemens SCALANCE X-200 Guía del administrador

Siemens

Siemens gigaset SE551 Manual de usuario

Siemens

Siemens Gigaset Optical LAN Adapter Duo Manual de usuario

Siemens

Siemens 5881 Manual de usuario

Siemens

Siemens RUGGEDCOM RS1600 Manual de usuario

Siemens

Siemens SIMATIC NET SCALANCE W778-1 Manual de usuario

Siemens

Siemens SpeedStream SS2624 Manual de usuario

Siemens

Siemens Gigaset SX541 WLAN dsl Manual de usuario

Siemens

Siemens N 146 Manual de servicio

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1400 Manual de usuario

Siemens

Siemens CL-110 Manual de usuario

Siemens

Siemens SIMATIC NET SCALANCE S615 Hoja de instrucciones

Siemens

Siemens RUGGEDCOM RX1500 Manual de usuario

Siemens

Siemens gigaset se 105 Manual de usuario

Siemens

Siemens RUGGEDCOM RS940G Manual de usuario

Siemens

Siemens PSFR-CP41 Cómo utilizar

Siemens

Siemens se5880 Manual de usuario

Siemens

Siemens SCALANCE M800 Manual de usuario

Siemens

Siemens 73 82 851 Manual

Siemens

Siemens RUGGEDCOM RSG2288 Manual de usuario

Siemens

Siemens CL-010 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad