Siemens SANTIS-ab Manual de usuario

User Manual for

SANTIS-ab

Subscriber Access and

Network Termination for ISDN Services

2

U

mains

230VAC / 50Hz

LED for local feeding

SIEMENS

LED for remote feeding

a/b1 a/b2

S S

3

Contents

1. Safety Instructions.....................................................................4

2. Operating Modes .......................................................................5

3. Installation.................................................................................6

4. Configuration ............................................................................8

5. Table of Configuration Commands......................................... 12

6. Troubleshooting ......................................................................26

7. Pin Allocations of the Sockets ................................................27

4

1. Safety Instructions

•Place the SANTIS-ab near a 230 V outlet.

•Do not open the case.

•Clean the case only with dry or moist cloth.

Never immerse into water.

•If the SANTIS-ab is damaged, inform immediately your

network provider.

5

2. Operating Modes

The connection to the public telephone network as well as the

selection of one of the following three operating modes must be

done by an authorized person, e.g. telecom staff:

1. NT+2ab S- and a/b-interfaces available

2. NTBA Only S-interface available

3. Pairgain Only a/b-interfaces available

6

3. Installation

•If both the green LEDs light steadily, the SANTIS-ab is ready

for operation (see figure on page 2).

The following installation-steps can be done by everyone.

•The SANTIS-ab can be wall-mounted or placed on the desk

(piling of more units is also possible). In case of wall

mounting, drill the holes into the wall according to the

enclosed drawing, insert dowels with wood screws and hang

on the SANTIS-ab.

7

•Connection of the terminal equipments:

The sockets for the analog equipments (e.g. telephones, gr.2/3

fax machines, modems) are designated with «a/b1» and

«a/b2», those for the ISDN terminal equipments with «S»

(e.g. ISDN-telephones, PC with ISDN-card, gr.4 fax

machines). See figure on page 2.

8

4. Configuration

•There are only parameters for the a/b-interfaces. Thus there is

only a need for a configuration, if the a/b-interfaces are

available (NT+2ab mode and Pairgain mode; see chapter 2).

The configuration remains stored, even after a power failure.

•The configuration is done by means of an analog telephone

set equipped with tone dialing, having both ∗and #keys.

Remark:

In normal use SANTIS-ab recognizes both pulse and tone

dialing.

•If the NT+2ab mode is selected, all the configuration

commands can be set from both the a/b-interfaces without

any restrictions.

9

If the configuration access (CA) is restricted (can be set and

changed by authorized persons, e.g. telecom staff), the

configuration for the a/b1-interface can only be done via the

a/b1-interface and vice versa for the a/b2-interface.

This mode is called NT+2ab/CA restr.

If the Pairgain mode is selected, the configuration access is

automatically restricted, i.e. the configuration for the a/b1-

interface can only be done via the a/b1-interface and vice

versa for the a/b2-interface.

10

The settings are executed as follows. See also flow chart on next

page.

1. Hook off and wait for dial tone

2. Dial ∗∗→The dial tone is switched off

3. Dial the command number and parameter value according to

the tables in chapter 5.

4. Dial #→If the parameter has been programmed

successfully, a permanent tone is switched on.

Otherwise a busy tone will be switched on.

5. Proceed with step 3. if necessary for setting other parameters

or hook on.

Tabla de contenidos

Otros manuales de Hardware de red de Siemens

Siemens

Siemens Caracas Desk Rel. 2.0 Manual de usuario

Siemens

Siemens Gigaset M 101 Data Manual de usuario

Siemens

Siemens SIMATIC NET CP 1515 Manual de usuario

Siemens

Siemens WTT16 Series Manual de usuario

Siemens

Siemens RUGGEDCOM WIN5149 Manual de usuario

Siemens

Siemens SIMATIC NET S7-1500 Manual de usuario

Siemens

Siemens RUGGEDCOM WIN5114-V-GPS Manual de usuario

Siemens

Siemens WTT662 Series Manual de usuario

Siemens

Siemens RUGGEDCOM RX1400 Manual de usuario

Siemens

Siemens Rider 11, Rider 13 H,Rider 11 Bio Manual de instrucciones

Siemens

Siemens SIMATIC NET SCALANCE W M766 Series Manual de usuario

Siemens

Siemens SIMATIC NET PROFIBUS Manual de usuario

Siemens

Siemens ISI EN 50295 Manual de usuario

Siemens

Siemens SIMATIC NET SCALANCE W774-1 Manual de usuario

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1536 Manual de usuario

Siemens

Siemens SIMATIC NET S7-400 Manual de usuario

Siemens

Siemens PROFIBUS DP-V1 Manual de usuario

Siemens

Siemens NK8222 Manual de lista de piezas

Siemens

Siemens Sinumerik 810T Manual de usuario

Siemens

Siemens NK8000 MP.4.60 Manual de lista de piezas

Siemens

Siemens SIMATIC NET SCALANCE M875 Manual de usuario

Siemens

Siemens RUGGEDCOM MX5000RE Documento técnico

Siemens

Siemens RUGGEDCOM WIN5237-IS Manual de usuario

Siemens

Siemens SIMATIC NET CP 1515 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario