Siemens SENTRON PAC5200 Guía de aplicación
E50417-H1040-C568-A1
Power Monitoring Device
and
Power Quality Recorder
SENTRON PAC5100/5200
7KM5212/5412
V1.00
Device Manual
Preface
Open Source Software
Contents
User Information 1
Overview 2
Device Design 3
Measurands and Recording 4
Getting Started 5
Connection Principle 6
Operation at Use of a PC 7
Operation at Use of the Display 8
Time Synchronization 9
Maintenance, Storage, Transport 10
Failures and LED Indications 11
Technical Data 12
Operational Indications 13
Operating Parameters 14
Glossary
Index
Disclaimer of Liability
This document has been subjected to rigorous technical review
before being published. It is revised at regular intervals, and any
modifications and amendments are included in the subsequent
issues. The content of this document has been compiled for
information purposes only. Although Siemens AG has made best
efforts to keep the document as precise and up-to-date as possible,
Siemens AG shall not assume any liability for defects and damage
which result through use of the information contained herein.
This content does not form part of a contract or of business
relations; nor does it change these. All obligations of Siemens AG
are stated in the relevant contractual agreements.
Siemens AG reserves the right to revise this document from time to
time.
Document version: E50417-H1040-C568-A1.00
Edition 03.2015
Version of the product described: V1.00
Copyright
Copyright Siemens AG 2015. All rights reserved.
The disclosure, duplication, distribution and editing of this
document, or utilization and communication of the content are not
permitted, unless authorized in writing. All rights, including rights
created by patent grant or registration of a utility model or a design,
are reserved.
Registered Trademarks
SENTRON®is a registered trademark of SIEMENS AG. An
unauthorized use is illegal.
All other designations in this document can be trademarks whose
use by third parties for their own purposes can infringe the rights of
the owner.
NOTE
For your own safety, please observe the warnings and safety instructions contained in this document.
3SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Preface
Purpose of this Manual
This manual describes the application, functions, installation, commissioning, and operation of the
Power Monitoring Device and Power Quality Recorder SENTRON PAC5100/5200 7KM5212/5412.
Target Group
This manual is intended for project engineers, commissioning and operating personnel in electrical systems
and power plants.
Scope of Validity of this Manual
This manual is valid for the Power Monitoring Device and Power Quality Recorder SENTRON PAC5100/5200
7KM5212/5412.
Further Support
For any questions concerning your system, please contact your Siemens representative.
Siemens provides around-the-clock support.
Phone: +49 (911) 895-7222
Fax: +49 (911) 895-7223
Internet: http://www.siemens.com/automation/service&support
Training Courses
If you are interested in our current training program, please contact our training center:
Siemens AG
Siemens Power Academy TD
Humboldtstr. 59
D-90459 Nuremberg
Tel.: +49 (911) 433-7415
Fax: +49 (911) 433-7929
Internet: http://www.siemens.com/poweracademy
e-mail: [email protected]
4SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Notes On Safety
This manual is not a complete index of all safety measures required for operation of the equipment (module,
device). However, it comprises important information that must be noted for purposes of personal safety, as
well as in order to avoid material damage. Information is highlighted and illustrated as follows according to the
degree of danger.
DANGER
DANGER means that death or severe injury will occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent death or severe injury.
WARNING
WARNING means that death or severe injury can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent death or severe injury.
CAUTION
CAUTION means that minor or moderate injury can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent minor injury.
NOTICE
NOTICE means that damage to property can occur if the appropriate safety measures are not taken.
✧Follow all advice instructions to prevent damage to property.
NOTE
is important information about the product, the handling of the product, or the part of the documentation in
question to which special attention must be paid.
5SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Personnel Qualified in Electrical Engineering
Only qualified electrical engineering personnel may commission and operate the equipment (module, device)
described in this document. Qualified electrical engineering personnel in the sense of this manual are people
who can demonstrate technical qualifications as electrical technicians. These persons may commission, iso-
late, ground, and label devices, systems and circuits according to the standards of safety engineering.
Use as Prescribed
The equipment (device, module) must not be used for any other purposes than those described in the Catalog
and the Technical Description. If it is used together with third-party devices and components, these must be
recommended or approved by Siemens.
If the device is not used in accordance with the operating instruction and this manual, the scheduled protection
is impaired.
Problem-free and safe operation of the product depends on the following:
• Proper transport
• Proper storage, setup, and installation
• Proper operation and maintenance
When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper ac-
tion is not taken, death, severe injury, or property damage can result.
• The equipment must be grounded at the grounding terminal before any connections are made.
• All circuit components connected to the power supply may be subject to dangerous voltage.
• Hazardous voltages may be present in equipment even after the supply voltage has been disconnected
(capacitors can still be charged).
• Equipment with exposed current transformer circuits must not be operated. Prior to disconnecting the
equipment, ensure that the current transformer circuits are short-circuited.
• The limit values stated in the document may not be exceeded. This must also be considered during testing
and commissioning.
6SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Used Symbols
No. Symbol Description
1 Direct current
IEC 60417-5031
2 Alternating current
IEC 60417-5032
3 Direct and alternating current
IEC 60417-5033
4 Three-phase alternating current
5 Earth (ground) terminal
IEC 60417-5017
6 Protective conductor terminal
IEC 60417-5019
7 Caution, risk of electric shock
8 Caution, risk of danger
ISO 7000-0434
7SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Statement of Conformity
Further Standards
For further information see UL database on the internet: http://ul.com.
Chose Online Certifications Directory and insert E228586 under UL File Number.
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility (EMC
Council Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage
limits (Low-voltage Directive 2006/95/EC).
This conformity has been established by means of tests conducted by Siemens AG according to the
Council Directive in agreement with the generic standards EN 61000-6-2 and EN 61000-6-4 for the
EMC directives, and with the standard EN 61010-1 for the low-voltage directive.
The device has been designed and produced for industrial use.
The product conforms to the standard IEC 61557-12.
This product is UL-certified to Standard UL 61010-1, third edition, based on the specification stated in Chapter 12
(Technical Data).
UL File No.: E228586
Open-type Measuring Equipment
2UD1
8SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
9SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Open Source Software
The product contains, among other things, Open Source Software developed by third parties. The Open
Source Software used in the product and the license agreements concerning this software can be found in the
Readme_OSS.
These Open Source Software files are protected by copyright. Your compliance with those license conditions
will entitle you to use the Open Source Software as foreseen in the relevant license. In the event of conflicts
between Siemens license conditions and the Open Source Software license conditions, the Open Source Soft-
ware conditions shall prevail with respect to the Open Source Software portions of the software.
The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software License
Conditions provide for it you can order the source code of the Open Source Software from your Siemens sales
contact - against payment of the shipping and handling charges - for a period of at least 3 years since purchase
of the Product. We are liable for the Product including the Open Source Software contained in it pursuant to
the license conditions applicable to the Product. Any liability for the Open Source Software beyond the program
flow intended for the Product is explicitly excluded. Furthermore any liability for defects resulting from modifi-
cations to the Open Source Software by you or third parties is excluded. We do not provide any technical sup-
port for the Product if it has been modified.
10 SENTRON PAC5100/5200, 7KM5212/5412, Device Manual
E50417-H1040-C568-A1, Edition 03.2015
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Instrumento de medición de Siemens
Siemens
Siemens SITRANS F M MAG 3100 Manual de usuario
Siemens
Siemens LDS 6 Manual de usuario
Siemens
Siemens FDUL221 Manual de usuario
Siemens
Siemens SITRANS F M MAG 8000 Manual de usuario
Siemens
Siemens sitrans PROBE LU Manual de usuario
Siemens
Siemens DCA Vantage Manual
Siemens
Siemens SITRANS F M MAG 8000 Manual de usuario
Siemens
Siemens SD 270 Manual de usuario
Siemens
Siemens SITRANS F C MC2 Manual de usuario
Siemens
Siemens SITRANS FX330 Manual de usuario
Siemens
Siemens SITRANS FUS380 Manual de usuario
Siemens
Siemens SITRANS F Manual de usuario
Siemens
Siemens multiranger 100 Manual de instrucciones
Siemens
Siemens FIDAMAT 5E Manual de usuario
Siemens
Siemens SITRANS F C MASSFLO MASS 2100 Guía del administrador
Siemens
Siemens 6 Series Guía del administrador
Siemens
Siemens DELTA 5TC8 425 Manual de servicio
Siemens
Siemens SENTRON 7KT PAC1200 Guía del usuario
Siemens
Siemens Pointek CLS200 Manual de usuario
Siemens
Siemens SITRANS F C MASSFLO MASS 2100 Manual de usuario
