Siemens OpenAir GIB Series Manual del propietario

Technical Instructions

Document Number 155-177P25

EA GBB/GIB-2

June 22, 2015

OpenAir™ GBB/GIB Series

Electronic Damper Actuators

Non-spring Return 24 Vac, Floating Control, Rotary

Siemens Industry, Inc.

Description The OpenAir direct coupled 24 Vac, non-spring return (NSR) rotary electric actuator

is designed for floating control of building HVAC dampers.

Features •Unique self-centering shaft coupling

•All metal housing

•Manual override

•Independently adjustable dual auxiliary switches available

•Built in potentiometer option

•Two torque ranges available

•UL, CE and cUL listed

Application These actuators are used in constant or variable air volume installations for the

control of return air, mixed air, exhaust,

and face and bypass dampers requiring up to

221 lb-in (25 Nm) or 310 lb-in (35 Nm) torque.

Product Numbers

Table 1.

24 Vac Operating Voltage

Torque Cabling Standard Potentiometer

Only

Auxiliary

Switches

Only

221 lb-in (25 Nm) Standard GBB131.1U GBB132.1U GBB136.1U

Plenum GBB131.1P GBB132.1P GBB136.1P

310 lb-in (35 Nm) Standard GIB131.1U GIB132.1U GIB136.1U

Plenum GIB131.1P — GIB136.1P

Technical Instructions OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control

Document No. 155-177P25

June 22, 2015

Page 2 Siemens Industry, Inc.

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you do not perform a procedure

as specified.

CAUTION:

Equipment damage or loss of data may occur if you do not perform a

procedure as specified.

Specifications

Power supply

Operating voltage 24 Vac, ±20%

Frequency 50/60 Hz

Power consumption: 7 VA/7W

Equipment rating

Operating voltage Class 2, in accordance with UL/CSA

Plenum type actuators as whole device Class 2, in accordance with UL/CSA

Auxiliary features

Feedback potentiometer (GBB132x)

Sliding contact (P2) 0 to 1000 ohm

Load <1W

Voltage <24 Vac/dc

Control signal adjustment

Offset (start point) Between 0 to 5 Vdc

Factory setting 0 Vdc

Span Between 2 to 30 Vdc

Dual auxiliary switches

AC rating (standard cable) 24 to 250 Vac

AC 6A resistive

AC 2A general purpose

AC rating (Plenum cable) 24 Vac

AC 4A resistive

AC 2A general purpose

DC rating (Standard/Plenum cable) 12 to 30 Vdc

DC 2A

Switch Range

Switch A 0 to 90° with 5° intervals

Recommended range usage 0 to 45°

Factory setting 5°

Switch B 0 to 90° with 5° intervals

Recommended range usage 45 to 90°

Factory setting 85°

Switching hysteresis 2°

WARNING:

Apply only line voltage or only Class 2 voltage to the switching outputs of both

auxiliary switches A and B. Mixed operation is not permissible. See Wiring for

details.

OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control Technical Instructions

Document No. 155-177P25

June 22, 2015

Siemens Industry, Inc. Page 3

Specifications,

Continued

Function

Running torque

GBB… 221 lb-in (25 Nm)

GIB… 310 lb-in (35 Nm)

Runtime for 90° opening or closing 150 seconds at 50 Hz

125 seconds at 60 Hz

Nominal angle of rotation 90°

Maximum angular rotation 95°

Mounting

Shaft size 3/8 to 1-inch (8 to 25.6 mm) diameter

1/4 to 5/8-inch (6 to 18 mm) square

Minimum shaft length 3/4-inch (20 mm)

Housing

Enclosure NEMA 2 in vertical position to 90°

to the left and right of vertical

See Figure 14.

NEMA 3R rated when installed with

ASK75.1U Weather Shield in the

vertical position. See Accessories.

IP54 according to EN 60 529

Material Die-cast aluminum alloy

Gear lubrication Silicone-free

Ambient conditions

Ambient temperature

operation -25°F to 130°F (-32°C to 55°C)

storage and transport -40°F to 158°F (-40°C to 70°C)

Ambient humidity (non-condensing) 95% rh

Agency certification

UL listed to UL873

cUL certified to Canadian Standard

C22.2 No. 24-93

CE conformity:

Electromagnetic compatibility 2004/108/EC

Low-voltage directive 2006/95/EC

Miscellaneous

Pre-cabled connection 18 AWG

Cable length 3 feet (0.9 m) length

Life cycle Designed for over 60,000 full strokes

and a minimum of 1.5 million

repositions at rated torque and

temperature

Noise level <45 dBA (running)

Dimensions See Figure 26.

Weight 4.4 lbs (2 kg)

Technical Instructions OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control

Document No. 155-177P25

June 22, 2015

Page 4 Siemens Industry, Inc.

Accessories NOTE: Neither the auxiliary switches nor the feedback potentiometer can be added in

the field. Order the product number that includes these options.

Figure 1. Floor Mount Kit.

ASK71.1U:

Allows foot mounting of the

OpenAir actuators. Kit should be used for

-the-air stream applications or anywhere

a foot

-mounted actuator can be mounted.

Kit contains:

•Crank arm for changing angular

rotation into a linear stroke

•

Support bearing ring to minimize side

loading on the actuator’s output

bearing

•Mounting bracket

•

Required mounting fasteners

Figure 2. Frame Mount Kit.

ASK71.2U:

Allows mounting of OpenAir

actuators directly to a damper frame. Kit

should be used with louvers and vents and

in applications where use of the floor

mount kit is not possible.

Kit contains:

•Crank arm to change the angular

rotation into a linear stroke

•

Support bearing ring to minimize side

loading on the actuator’s output

bearing

•Mounting bracket

•

Required mounting fasteners

Figure 3. Crank Arm Kit.

ASK71.3

: Allows a direct-coupled actuator

to provide an auxiliary linear drive. Kit can

be used to simultaneously drive a set of

opposing or adjacent dampers with a

single actuator.

Kit contains:

•Crank arm to attach to the splined

hub of the shaft adapter

•

Required mounting fasteners

Figure 4. Crank Arm Kit with Mounting

Bracket.

ASK71.4: Allows economical mounting of

an OpenAir actuator to a variety of

surfaces. Kit should be used in

applications where the actuator can be

rigidly surface mounted and a linear stroke

output is required. Kit contains:

•Crank arm to attach to the splined

hub of the shaft adapter

•Mounting bracket

•Required mounting fasteners

OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control Technical Instructions

Document No. 155-177P25

June 22, 2015

Siemens Industry, Inc. Page 5

Accessories,

continued

Figure 5. Tandem Mount Bracket.

ASK73.1: Bracket provides an extended

anti-rotation pin that allows two GIB13x

OpenAir actuators to directly drive a

single damper shaft. For use with three-

position actuators.

Figure 6. Special Shaft Adapter.

ASK74.1U:Shaft adapter attaches to a

1.05-inch (26.6 mm) diameter shaft;

whereas, the standard self-centering

adapter accepts up to a 1.00-inch

(25.4 mm) diameter shaft.

Adapter can be used for coupling to

inch (25 mm) jackshafts that are slightly

oversized. Adapter is 13/16-inches (20

mm) shorter than the height of the self-

centering shaft adapter.

985-052P20: (no picture) Small shaft

insert (package of 20) when using the

GIB actuator on a damper shaft less than

3/4-inch (20 mm) diameter.

Figure 7. NEMA 3R Weather Shield.

ASK75.1U: GBB/GIB actuators are UL

listed to meet NEMA 3R requirements (a

degree of protection against rain, sleet,

snow, and damage from external ice

formation) when installed with the

ASK75.1U Weather Shield and

outdoor-rated conduit fittings in the

vertical position.

For dimensions, see Figure 24.

Figure 8. NEMA Type 4X Weather Shield.

ASK75.7U: GBB and GIB Actuators are

UL listed to meet NEMA Type 4X

requirements (a degree of protection

against falling dirt, rain, sleet, snow,

windblown dust, splashing water, hose-

directed water, corrosion, and damage

from external ice formation) when

installed with an ASK75.7U Weather

Shield and outdoor-rated conduit fittings.

This weather shield may be mounted in

any orientation.

For dimensions, see Figure 25.

Figure 9. Heater/Weather

Shield Assembly.

985-106: Provides protection for GIB,

GBB and GCA OpenAir actuators in an

outside low temperature. Assembly

includes:

•Weather Shield (ASK75.1U)

•Heater Kit (985-105)

Technical Instructions OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control

Document No. 155-177P25

June 22, 2015

Page 6 Siemens Industry, Inc.

Figure 10. Conduit Adapter.

985-008: 1/2-inch (12 mm) for

1/2-inch NPT connector.

Service Parts

985-003

Position Indicators

(package of 10)

985-004

Standard Shaft Adapter

985-006

Anti-rotation (Mounting) Bracket

Figure 11. Orderable Parts.

Actuator

Components

Legend

1. Positioning scale for angle of

rotation

2. Connection cables

3. Manual override

4. Auxiliary switch B

5. Auxiliary switch A

6. Position indicator

7. Self-centering shaft adapter

8. Shaft adapter locking clip

9. Position indicator adapter

10. Mounting bracket

Figure 12. Components of the Floating Control Actuator.

OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control Technical Instructions

Document No. 155-177P25

June 22, 2015

Siemens Industry, Inc. Page 7

Operation GBB/GIB13x

A floating control signal controls the damper actuator. The actuator’s angle of rotation is

proportional to the length of time the signal is applied. A 24 Vac control signal to wires 1

and 6 (G-Y1) causes the actuator coupling to rotate clockwise. A 24 Vac control signal

to wires 1 and 7 (G-Y2) causes the actuator coupling to rotate counterclockwise.

If you want to reverse the direction of rotation, wires 6 and 7 (Y1 and Y2) may be

interchanged. Reverse the position indicator so that the counterclockwise 0 to 90 scale

is visible. See Figure 17.

In the event of a power failure or with no control voltage, the damper actuator holds its

position.

In the event of a blockage in the damper, the actuator is overload protected over the full

range to prevent damage to the actuator.

Life expectancy An improperly tuned loop will cause excessive repositioning that will shorten the life of

the actuator.

Dual auxiliary switch

GBB/GIB136

Actuator Scale:

Clockwise

Adjustment range for Switches A and B

Setting interval: 5°

Switching hysteresis: 2°

Actuator Scale:

Counterclockwise

NOTE: The auxiliary switch setting shafts turn together with the actuator. The scales

are valid only when the actuator is in the “0” position on clockwise motion.

To change the settings of A and B, use a

flat-blade screwdriver to turn the switch

adjustment dials to the desired setting at

which a signal is to be given.

Factory setting

Switch A 5°

Switch B 85°

Figure 13. Dual Auxiliary Switch Dials.

Technical Instructions OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control

Document No. 155-177P25

June 22, 2015

Page 8 Siemens Industry, Inc.

Sizing The number of actuators required depends on several factors. To determine the quantity

of actuators required for the installation:

1. Obtain damper torque ratings (ft-lb/ft2or Nm/m2) from the damper manufacturer.

2. Determine the area of the damper.

3. Calculate the total torque required to move the damper:

Total Torque = Torque Rating × Damper Area

4. Select the total quantity of actuators required:

Number of actuators =

ions)Specificat

(Refer

Torque

tor

x ActuaSF required

Torque

Damper

Total

1Safety Factor: When calculating the number of actuators required, a safety factor

should be included for unaccountable variables such as slight misalignments, aging of

the damper, etc. A suggested safety factor is 0.80 (or 80% of the rated torque).

Mechanical coupling of the actuator is allowed if:

1. The same type of actuator is used.

2. The power trunk can handle added components.

3. The same power and control inputs go to both actuators (parallel wiring).

Mounting and

Installation

Figure 14. Acceptable NEMA 2 positions.

•The actuator must be placed on the damper shaft so that the front of the actuator is

accessible. The label and the manual override button are the front side.

•The minimum damper drive shaft length is 3/4-inch (20 mm). The shaft length

determines whether the shaft adapter will be mounted on the front or back side of

the actuator.

•See Specifications for minimum and maximum damper shaft dimensions.

•Mount the position indicator to show either the clockwise or counterclockwise 0 to 90

scale.

•A mounting bracket is included with the actuator.

- Detailed mounting instructions are included with each actuator.

- The shaft adapter and mounting parts are shipped in a separate container with

the actuator.

•The actuator is shipped from the factory with a 5° pre-load to ensure tight close off

of the damper.

OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control Technical Instructions

Document No. 155-177P25

June 22, 2015

Siemens Industry, Inc. Page 9

Manual override To move the damper blades and lock

the position with no power present:

1. Determine damper rotation:

clockwise or counterclockwise.

2. Hold down the PUSH button.

3. Make adjustments to the damper

position.

4. Release the PUSH button.

Once power is restored, the actuator

returns to automated control.

Figure 15. Manual Override.

Mechanical range

adjustment The angular rotation is adjustable between 0 and

90° at 5-degree intervals. The range of shaft

movement is limited by mounting the shaft

adapter:

Begin by loosening the shaft adapter from the

damper shaft and remove the actuator from the

damper shaft.

1. Remove clip.

2. Remove shaft adapter from the actuator.

Figure 16.

Figure 17.

Figure 18.

Figure 19.

3. Return the actuator gear train to the “0” position using the following steps for the

clockwise or counterclockwise damper shaft rotation.

Clockwise-to-open:

a. Insert the shaft adapter to the right as close as possible to the raised stop.

See Figure 17.

b. Hold down the PUSH button and rotate the shaft adapter to the left until it

stops. See Figure 18.

c. Release the PUSH button.

d. If the shaft adapter is not resting against the left raised stop, remove the

adapter and insert it against the left stop.

e. Place the position indicator to the "0" position on the outside scale. See

Figure 19.

Technical Instructions OpenAir™ GBB/GIB Series Non-spring Return, 24 Vac, Floating Control

Document No. 155-177P25

June 22, 2015

Page 10 Siemens Industry, Inc.

Mechanical range

adjustment, continued Counterclockwise-to-open:

a. Insert the shaft adapter to the left as close as possible to the raised stop.

b. Hold down the PUSH button and rotate the shaft adapter to the right until it

stops.

c. Release the PUSH button.

d. If the shaft adapter is not resting against the right raised stop, remove the

adapter and insert it against the right stop.

e. Place the position indicator to “0” on the inside scale.

4. Determine the angle of rotation for the damper blade shaft. Subtract that amount

from 90°.

5. Remove the shaft adapter and insert it with the position indicator pointing to the

mark on the scale calculated in the previous step. See Figure 20.

6. Attach the clip.

7. Rotate the damper blade shaft to its "0" position.

8. Return the actuator to the damper shaft and tighten the shaft adapter to the damper

shaft.

Figure 20. Mechanical Range Adjustment.

Reversing the position

indicator Reverse the position indicator so that the counterclockwise 0 to 90 scale is visible.

Figure 21. Position Indicator.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Siemens

Siemens

Siemens RLM162 Manual de usuario

Siemens

Siemens Reyrolle 7SR45 Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de lista de piezas

Siemens

Siemens SIMATIC S7-200 Manual de usuario

Siemens

Siemens SIPLUS HCS3200 Guía del administrador

Siemens

Siemens PXC Series Manual de usuario

Siemens

Siemens RAJA+ Instrucciones de funcionamiento

Siemens

Siemens SIRIUS 3RW44 Manual de usuario

Siemens

Siemens SITOP PSU8600 Manual de usuario

Siemens

Siemens 7SR224 Instrucciones de funcionamiento e instalación

Siemens

Siemens BR6000 Manual de usuario

Siemens

Siemens SIRIUS 3RW30 Manual de usuario

Siemens

Siemens Powermite 599 Series Manual del propietario

Siemens

Siemens SIPROTEC 5 Instrucciones de funcionamiento e instalación

Siemens

Siemens SKB32 Series Manual de usuario

Siemens

Siemens GGA Series Manual de usuario

Siemens

Siemens S7-1200 TELECONTROL Guía del usuario

Siemens

Siemens SINUMERIK 840 Manual técnico

Siemens

Siemens GCA Series Manual de usuario

Siemens

Siemens SIMATIC Mobile Client900WXN Manual de usuario

Siemens

Siemens EM 300 Manual de usuario

Siemens

Siemens GEB 1 Series Manual de usuario

Siemens

Siemens SIPART DR21 Manual de usuario

Siemens

Siemens SIRIUS 3RW44 Guía del usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario