Siemens SINAMICS G120 CU250S-2 Series Guía del administrador

CU250S-2 Control Units

___________________

SINAMICS

SINAMICS G120

CU250S-2 Control Units

Compact Operating Instructions

05/2014

A5E32899990B AB

Fundamental safety

instructions

Scope of delivery

Installing

Commissioning

More information

Scan the QR code for

additional informati-

on on SINAMICS

G120.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E32899990B AB

Ⓟ

07/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

CU250S-2 Control Units

Compact Operating Instructions, 05/2014, A5E32899990B AB 3

Table of contents

1 Fundamental safety instructions.............................................................................................................. 4

1.1 General safety instructions ............................................................................................................4

1.2 Industrial security ...........................................................................................................................5

2 Scope of delivery .................................................................................................................................... 6

3 Installing ................................................................................................................................................. 7

3.1 Snapping the Control Unit onto the Power Module........................................................................7

3.2 Overview of the interfaces .............................................................................................................8

3.3 Terminal blocks ............................................................................................................................10

3.4 Operator panels ...........................................................................................................................14

4 Commissioning ..................................................................................................................................... 15

4.1 Commissioning with STARTER ...................................................................................................15

4.2 Connecting the inverter to the fieldbus ........................................................................................20

4.3 Frequently required parameters...................................................................................................22

5 More information................................................................................................................................... 25

5.1 Manuals for your inverter .............................................................................................................25

5.2 Product support............................................................................................................................26

This manual describes how you install a SINAMICS G120 converter with CU250S-2 Control

Unit and commission it.

What is the meaning of the symbols in the manual?

An operating instruction starts here.

This concludes the operating instru

ction.

CU250S-2 Control Units

4 Compact Operating Instructions, 05/2014, A5E32899990B AB

Fundamental safety instructions

1.1

General safety instructions

WARNING

Risk of death if the safety instructions and remaining risks are not carefully observed

If the safety instructions and residual risks are not observed in the associated hardware

documentation, accidents involving severe injuries or death can occur.

•Observe the safety instructions given in the hardware documentation.

•Consider the residual risks for the risk evaluation.

WARNING

Danger to life or malfunctions of the machine as a result of incorrect or changed

parameterization

As a result of incorrect or changed parameterization, machines can malfunction, which in

turn can lead to injuries or death.

•Protect the parameterization (parameter assignments) against unauthorized access.

•Respond to possible malfunctions by applying suitable measures (e.g. EMERGENCY

STOP or EMERGENCY OFF).

Fundamental safety instructions

1.2 Industrial security

CU250S-2 Control Units

Compact Operating Instructions, 05/2014, A5E32899990B AB 5

1.2

Industrial security

Note

Industrial security

Siemens provides products and solutions with

industrial security functions that support the

secure operation of plants, solutions, machines, equipment and/or networks. They are

important components in a holistic industrial security concept. With this in mind, Siemens’

products and solutions undergo continuous development. Siemens recommends strongly that

you regularly check for product updates.

For the secure operation of Siemens products and solutions, it is necessary to take suitable

preventive action (e.g. cell protection concept) and integrate eac

h component into a holistic,

state

-of-the-art industrial security concept. Third-party products that may be in use should

also be considered. For more information about industrial security, visit Hotspot

-Text

(

http://www.siemens.com/industrialsecurity).

To stay informed about product updates as they occur, sign up for a product

-specific

newsletter. For more information, visit Hotspot

-Text (http://support.automation.siemens.com

WARNING

Danger as a result of unsafe operating states resulting from software manipulation

Software manipulation (e.g. by viruses, Trojan horses, malware, worms) can cause unsafe

operating states to develop in your installation which can result in death, severe injuries

and/or material damage.

•Keep the software up to date.

You will find relevant information and newsletters at this address

(http://support.automation.siemens.com).

•Incorporate the automation and drive components into a holistic, state-of-the-art

industrial security concept for the installation or machine.

You will find further information at this address

(http://www.siemens.com/industrialsecurity).

•Make sure that you include all installed products into the holistic industrial security

concept.

CU250S-2 Control Units

6 Compact Operating Instructions, 05/2014, A5E32899990B AB

Scope of delivery

The delivery comprises at least the following components:

●A CU250S-2 Control Unit ready for operation with installed firmware.

Options for upgrading and downgrading the firmware can be found on the Internet:

Firmware (http://support.automation.siemens.com/WW/news/en/67364620).

The fieldbus interface of the Control Unit depends on the order number.

The order number, the designation and the version of the hardware (e.g. 02)

and firmware (e.g. 4.6) can be found on the rating plate

①

of the Control Unit.

Designation

Order number

Fieldbus

CU250S-2 6SL3246-0BA22-1BA0 USS, Modbus RTU

CU250S-2 DP

6SL3246-0BA22-1PA0

PROFIBUS

CU250S-2 PN

6SL3246-0BA22-1FA0

PROFINET, EtherNet/IP

CU250S-2 CAN 6SL3246-0BA22-1CA0 CANopen

●Compact Operating Instructions in German and English

●The inverter contains open-source software (OSS). The OSS license terms are saved in

the inverter.

Transferring license terms of the OSS code to a PC

Procedure

To transfer the OSS license terms from the inverter to a PC, proceed as follows:

1. Switch off the inverter power supply.

2. Insert an empty memory card into the card slot of the inverter. Also see Section:Overview

of the interfaces (Page 8)

3. Switch on the inverter power supply.

4. When you have switched on the power supply, wait 30 seconds.

During this time, the inverter writes the "Read_OSS.ZIP" file onto the memory card.

5. Switch off the inverter power supply.

6. Remove the card from the inverter.

7. Use a card reader and load the file to a PC.

You have then transferred the OSS license terms from the inverter to a PC.

CU250S-2 Control Units

Compact Operating Instructions, 05/2014, A5E32899990B AB 7

Installing

3.1

Snapping the Control Unit onto the Power Module

Installing the Control Unit on an IP20 Power Module

Procedure

Proceed as follows to connect Power

Modules and Control Units:

Locate the lugs at the rear of the Control

Unit in the matching recesses of the

Power Module.

Mount the Control Unit onto the Power

Module so that it audibly snaps into place.

The Power Module and the Control Unit are now connected with one another.

To remove the Control Unit, press on the release button on the Power Module and withdraw

the Control Unit.

Permissible Power Modules

You may operate the Control Unit with the following Power Modules:

●PM240

●PM240-2

●PM250

●PM260

●PM340 1AC

Installing

3.2 Overview of the interfaces

CU250S-2 Control Units

8Compact Operating Instructions, 05/2014, A5E32899990B AB

3.2

Overview of the interfaces

To access the interfaces at the front of the Control

Unit, you must unplug the Operator Panel (if one is

being used) and open the front doors.

①

Terminal strips

②

Fieldbus interface

Selecting the fieldbus address:

•

PROFIBUS

•

USS

•

Modbus RTU

•

CanOpen

③

Status LED

④

USB interface for connection to

a PC

⑤

No function. Keep the switch in the "Vector"

position.

⑥

Switch for analog inputs

0/4 mA … 20 mA

10/0 V … 10 V

⑦

Connection to the operator panel

⑧

Memory card slot

Installing

3.2 Overview of the interfaces

CU250S-2 Control Units

Compact Operating Instructions, 05/2014, A5E32899990B AB 9

Interfaces at the lower side of the Control Unit

Table 3- 1 Permissible encoders on the DRIVE-CLiQ interface X100

DRIVE-CLiQ

encoder

Resolver

HTL

encoder

TTL

encoder

SSI

encoder

Endat 2.1

sin/cos

encoder

Direct connection

✓

---

Connection via Sensor Module

SMC10, SMC20, SMC30, SME20

or SME25

--- ✓✓✓✓✓✓

The permissible combinations of encoders for speed control and position control are listed in

the "Basic Positioner" Function Manual, see also: Manuals for the Control Unit

(http://support.automation.siemens.com/WW/view/en/30563628/133300).

Installing

3.3 Terminal blocks

CU250S-2 Control Units

10 Compact Operating Instructions, 05/2014, A5E32899990B AB

3.3

Terminal blocks

Terminal strips behind the upper front door

Different reference potentials:

The terminals labelled "GND" are connected internally.

"GND" and "GND IN" are not connected internally.

Figure 3-1 Interconnection example of the digital inputs with external 24 V power supply

Interconnecting the analog inputs (terminals 3, 4 and 10, 11)

For the analog inputs, you may use the internal 10 V supply (example: terminals 1 … 4, 13)

or an external supply (example: terminals 10, 11).

If you use the internal 10 V supply, you must connect AI 0- or AI 1- to GND.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Siemens

Siemens

Siemens LME11 series Manual de usuario

Siemens

Siemens REP-1 Manual de usuario

Siemens

Siemens SINAMICS Startdrive Manual de usuario

Siemens

Siemens SIMATIC S7 3964 Manual de instrucciones

Siemens

Siemens SITRANS F Manual de usuario

Siemens

Siemens VVI46 /2 Series Manual de usuario

Siemens

Siemens MJ-XL Manual de usuario

Siemens

Siemens MLC Manual de usuario

Siemens

Siemens FN2006-U1 Guía

Siemens

Siemens SINUMERIK 840Di sl Manual de lista de piezas

Siemens

Siemens SIMATIC ET 200AL Manual de usuario

Siemens

Siemens SINUMERIK 802D Guía de instalación

Siemens

Siemens ASR61EX Manual de usuario

Siemens

Siemens SIRIUS 3RW5 series Manual de usuario

Siemens

Siemens Simatic S7-1500 Manual de usuario

Siemens

Siemens SIRIUS 8WD4428-0BF Manual de usuario

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Manual de usuario

Siemens

Siemens MVS661 N Series Manual de usuario

Siemens

Siemens SIPROTEC 7SJ80 Manual de usuario

Siemens

Siemens 3RA2816-0EW20 Manual de usuario

Siemens

Siemens SINAMICS G120 Manual de usuario

Siemens

Siemens FT2001-A1 Manual de usuario

Siemens

Siemens 3RK1408-8K.00-0AA2 Manual de usuario

Siemens

Siemens SIRIUS 3SB3 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario