Siemens FS-TRI-M Manual de usuario

SiemensBuilding Technologies, Inc.

FlorhamPark, New Jersey 07932

RED BLK ORG ORG GRN

EARTH

GND

TOCONTROL PANEL

ORPREVIOUS ADDRESSABLE DEVICE

MODEL: FS-TRI-M

REFER TO INSTL. INSTR.

P/N 315-699487

DEVICE ADDR.__________

ALLTERMINALS ARE POWERLIMITED

NOTE:

DO NOT USE

REAR CONDUIT ENTRY

SINGLE GANG

SWITCHBOX

(USER SUPPLIED)

SINGLE GANG

SWITCHPLATE (BLANK)

(USER SUPPLIED)

FS-TRI-M

UNDERWRITERS

LABORATORIES

The SIEMENS FS-TRI-M Contact Monitoring Module,

as shown in Figure 1, interfaces normally open contact

devices to an ddressable Device Circuit of a fire

alarm control unit.

The FS-TRI-M supports Style B (Class B) Initiating

Device Circuit wiring. Each module uses one address

on the ddressable Device Circuit. It does not require

any mechanical address programming. Use the FS-FPI

Programmer/Tester to program and test the module.

PROGRAMMING INSTRUCTIONS

CAUTION:

1. To prevent damage to the FS-FPI, do not

connect module to the FS-FPI until the

Addre able Device Circuit wiring i

di connected.

2. Only one device mu t be connected to the

FS-FPI at a time.

1. Connect the red and black wires of the FS-TRI-M

to the SIEMENS FS-FPI Programmer/Tester. Use

the cable provided with the Programmer/Tester

and the 2 alligator clips provided.

2. Set the address for the module by following the

instructions in the FS-FPI Programmer/Tester

Manual (P/N 315-699480).

3. Record the device address on the label located

on the module. The module can now be installed

and wired to the system.

MOUNTING

The FS-TRI-M mu t be in talled in a

UL Li ted electrical box.

Refer to Figure 2.

1. Connect the appropriate wires using wire nuts.

Tuck the FS-TRI-M module inside the electrical

box and dress the wiring as required.

2. Fasten the cover plate (user supplied) to the box.

Figure 2

FS-TRI-M Mounting

P/N 315-699487-1

Siemens Building Technologies, Inc.

8 ernwood Road

lorham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Installation Instructions

Models FS-TRI-M

Contact Monitoring Module

Fire Safety

Figure 1

FS-TRI-M Module

Figure 3

FS-TRI-M Wiring

NOTES:

1. ll circuits are power limited.

2. In supervisory:

FS-TRI-M draws 1.5m

3. Initiating Device Circuit ratings:

Style B, Class B

See NFP 72 standard for the number of normally open contact devices allowed.

Voltage (max.): 5 VDC (during polling)

Supervisory current (max.): 0.5m (during polling)

larm current (max.): 0.8m (during polling)

IDC cable requirements:

Wire size: 18 to 14 WG

Wire resistance (max.): 2 ohms

Cable length (max.): 200 feet

Cable Type: Data grade, twisted pair

4. If Earth Ground is available, the green wire should be connected to earth ground.

5. If Earth Ground is NOT available, the IDC wiring should be limited to the same room.

RED

BLACK

GREEN

ORANGE

FS-TRI-M

-TO NEXT

ADDRESSABLE DEVICE

FROM ADDRESSABLE DEVICE

CIRCUIT OF A COMPATIBLE

CONTROL UNIT OR PREVIOUS

ADDRESSABLE DEVICE

GROUND

SEE NOTES 4 AND 5

END OF LINE RESISTOR

P/N 140-820185

3.6K, 1/4W, 5%

CONTACT DEVICE

INITIATING DEVICE CIRCUIT

SUPERVISED, SEE NOTE 3

ADDRESSABLE DEVICE CIRCUIT

24VDC NOMINAL, SUPERVISED

WIRING

Remove all y tem power before in tallation, fir t battery and then AC.

(To power up, connect AC first then battery.)

Refer to the wiring diagram and wire the module accordingly.

P/N 315-699487-1

Otros manuales de Unidad de control de Siemens

Siemens

Siemens SINAMICS S Series Manual de usuario

Siemens

Siemens SIMATIC 505 PPX:505-6108A Manual de usuario

Siemens

Siemens Flowrite 599 Series Manual del propietario

Siemens

Siemens QPA228.FWNC Series Manual de usuario

Siemens

Siemens SIPROTEC 7SJ80 Manual de usuario

Siemens

Siemens FM 458-1 DP Manual de usuario

Siemens

Siemens SIMATIC ET 200SP Manual de usuario

Siemens

Siemens SPCW110 Manual de usuario

Siemens

Siemens OLM/P11 V4.0 Manual de usuario

Siemens

Siemens SCALANCE W788C-2 Manual de usuario

Siemens

Siemens SIMOTION D4 Series Manual de usuario

Siemens

Siemens SIMATIC ET 200SP HA Guía del usuario

Siemens

Siemens SINAMICS G120 CU250S-2 Series Guía del administrador

Siemens

Siemens SIRIUS 3SB3 Manual de usuario

Siemens

Siemens SINUMERIK 808D Guía de instalación

Siemens

Siemens VAI60.15-15 Manual de usuario

Siemens

Siemens VVF Series Manual de usuario

Siemens

Siemens SIRIUS 3RU Series Manual de usuario

Siemens

Siemens SIWAREX FTC Guía de aplicación

Siemens

Siemens MJ-XL Manual de usuario

Siemens

Siemens 6MB5110-1 Manual de usuario

Siemens

Siemens RMB795B Manual del operador

Siemens

Siemens SIMATIC ET 200S Manual de usuario

Siemens

Siemens SIRIUS Star-Delta Combination S2 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario