Siemens SIMATIC PCS 7 Guía del usuario

SIMATIC

Process Control System PCS 7

What's new in SIMATIC PCS 7

(V8.0)?

System Manual

12/2011

A5E02779862-01

What's new in SIMATIC PCS

7 V8.0 compared to V7.1?

Engineering Station - What's

new in PCS 7 V8.0?

Operator Station - What's

new in PCS 7 V8.0?

SIMATIC BATCH - What's

new in SIMATIC BATCH

V8.0?

SIMATIC Route Control -

What's new in SIMATIC

Route Control V8.0?

SIMATIC PDM - What's new

in PDM V8.0?

Process Historian - What's

new?

Documentation - What's

new?

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the relevant information is not taken into account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be

used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property

damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified

personnel are those who, based on their training and experience, are capable of identifying risks and avoiding

potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or

approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described.

Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in

this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E02779862-01

Ⓟ 05/2012 Technical data subject to change

Table of contents

1 What's new in SIMATIC PCS 7 V8.0 compared to V7.1?.............................................................................5

2Engineering Station - What's new in PCS 7 V8.0?.......................................................................................7

2.1 CFC - Engineering What's new in CFC V8.0?..............................................................................7

2.2 PO - What's new in PO V8.0?.......................................................................................................8

2.3 PH - What's new in PH V8.0?........................................................................................................8

2.4 APL - What's new in the Advanced Process Library V8.0?...........................................................8

2.5 APL - What's new in the Advanced Process Faceplates V8.0?..................................................10

2.6 Basic Library - What's new in the Basic Library V8.0?................................................................11

3 Operator Station - What's new in PCS 7 V8.0?..........................................................................................13

4 SIMATIC BATCH - What's new in SIMATIC BATCH V8.0?.......................................................................15

5 SIMATIC Route Control - What's new in SIMATIC Route Control V8.0?...................................................19

6 SIMATIC PDM - What's new in PDM V8.0?...............................................................................................21

7 Process Historian - What's new?................................................................................................................25

8 Documentation - What's new?....................................................................................................................27

What's new in SIMATIC PCS 7 (V8.0)?

System Manual, 12/2011, A5E02779862-01 3

What's new in SIMATIC PCS 7 V8.0 compared to

V7.1? 1

The following paragraphs provide an overview of the most important functional enhancements

and expansions in SIMATIC PCS 7 V8.0 compared to SIMATIC PCS 7 as of V7.1.

Overview of highlights

●Operating system

SIMATIC PCS 7 V8.0 runs on the following operating systems:

– For engineering station, single-station system and OS client:

- Windows 7 Ultimate/Enterprise SP1 (32-bit or 64-bit)

- Windows XP Professional SP3 (32-bit)

– For engineering station, single-station system and OS server:

- Windows Server 2008 R2 SP1 (64-bit)

- Windows Server 2008 SP2 (32-bit)

- Windows Server 2003 R2 SP2 (32-bit)

- Windows Server 2003 SP2 (32-bit)

Engineering Station

● SIMATIC PCS 7 Maintenance Station

The Maintenance Station provides information on the status of all SIMATIC PCS 7

components in hierarchically structured diagnostics screens.

The maintenance station can be configured as a single-station or multiple-station system.

● Support of PROFINET as fieldbus

The PROFINET fieldbus system enables the connection of existing field devices from

PROFIBUS DP and PROFIBUS PA and distributed I/Os.

● Redundant, fault-tolerant terminal bus

● Cyclic archiving of projects and readback of block parameters

Process Historian/Information Server

The new Process Historian with Reporting System is introduced with SIMATIC PCS 7 V8.0.

SIMATIC PCS 7 Advanced Engineering (AdvES)

Advanced ES V8.0 is also available for SIMATIC PCS 7 V8.0 with the following highlights:

● Workflow Guide for a guided engineering process

● Definition of variants for the control modules to reduce the number of templates

● Bulk engineering for PCS 7 alarms

What's new in SIMATIC PCS 7 (V8.0)?

System Manual, 12/2011, A5E02779862-01 5

SIMATIC PCS 7 RACK PC

● New type, SIMATIC IPC547D

● Configurators enable increased flexibility in terms of the selection of SIMATIC Rack PCs

PROFINET Integration

SIMATIC PCS 7 V8.0 consistently supports PROFINET along with the proven PROFIBUS DP/

PA. The following automation systems are available for PROFINET integration:

Standard automation system via PROFINET interface in the CPU (CPU 414-3PN and CPU

416-3PN) or communication module CP 443-1

Automation systems

In addition to the known automation systems

● Standard

● Fail-safe

● Fault-tolerant

● PC-based

PCS 7 mEC RTX are available as of SIMATIC PCS 7 V8.0 as additional automation systems.

A number of centrally connected IO modules are also supported with PCS 7 mEC RTX. These

features provide a cost-effective solution for small-scale applications and distributed control

systems.

Extension of the APL and Basic Library

● Diverse new blocks extend the APL functionality

● System blocks for compact drives and for the connection of Motor Management Systems

in accordance with PROFIdrive Profile

● Fluttering suppression for diagnostic, remove module and insert module interrupts

Batch

● Performance improvements with an AS-based operating mode

● Revision of diverse controls and dialogs

Licensing

● With SIMATIC PCS 7 V8.0, the number of licenses displayed has been reduced significantly

● Licenses are consistently separated from the function and scalable quantity framework,

whereby all scalable license are run as count-relevant.

What's new in SIMATIC PCS 7 V8.0 compared to V7.1?

What's new in SIMATIC PCS 7 (V8.0)?

6System Manual, 12/2011, A5E02779862-01

Engineering Station - What's new in PCS 7 V8.0? 2

2.1 CFC - Engineering What's new in CFC V8.0?

Version 8.0 contains the following extensions or changes compared to the previous version, V 7.1.2:

●Fine-grained operating permissions

You can use the new "Op_Level" attribute to configure levels of operator authorization levels

for a block type.

●Block encryption

CFC supports the encryption of individual blocks

●New concept for process tag types and process tags

In addition to process tag types and process tags, there are now control module types and

control module units. These support instance-specific changes in case of process tag

synchronization and several versions of process tag types. Enhanced data communication

with PCS 7 Advanced ES is also possible.

Version 7.1.2 includes the following extensions or changes compared to the previous version, V7.1:

●Number of possible AS-wide interconnections

The maximum number of AS-wide interconnections is no longer limited to a specific number

but is determined by checking the transfer volume over time. The additional load of the

configured CPU due to AS-wide interconnections is calculated based on the following

parameters:

– Data types of the interconnections

– Cycle times of the send and receive OBs

– Performance of the configured CPU

If the maximum value for the configured CPU is exceeded, an error message is output.

It may no longer be possible to compile a program with AS-wide interconnections that could

be run with the previous version. This is the case if the default of 30% maximum CPU load

for AS-wide interconnections in this program has been exceeded. If you increase this default

to the correct value, then you will be able to compile the program once again.

●The "Force" functionality now supports a higher number of I/Os

A maximum of 8192 I/Os can now be forced (8192 standard and 8192 F I/Os)

●New configuration options for locations

– Several instances can now be created from a location type

– There are now standard location types with fixed names

– A range of numbers for locations can be specified in the project

What's new in SIMATIC PCS 7 (V8.0)?

System Manual, 12/2011, A5E02779862-01 7

2.2 PO - What's new in PO V8.0?

Version 8.0 contains the following extensions or changes compared to V7.1:

● Compression of archive tags in the process object view

Archive tags can now be compressed. Collection and storage of the archive tags is now

only performed when the configured acquisition cycle has expired or the specified tolerance

range is exceeded.

2.3 PH - What's new in PH V8.0?

Version 8.0 contains the following extensions or changes compared to version 7.1.2:

● PDM Diagnostics

The new "PDM diagnostics" function allows the status of the field devices to be queried

and displayed. PDM Diagnostics does not require a Maintenance ES license.

● Basic diagnostics

With the new "Basic diagnostics" function, it is possible to use the basic functionality of

diagnostics without a license. Basic diagnostics monitors PC stations, network objects and

AS stations. Detailed diagnostics of the AS stations and the expansion with the user

diagnostics area require the "Maintenance ES" and "Maintenance RT" licenses.

● Shadow hierarchy (only relevant when using SIMATIC BATCH and SIMATIC RC)

Using the menu command "Options > Plant Hierarchy > Import Process Cell", you can

import objects from one multiproject to another. These imported objects are represented a

shadow hierarchy in the PH.

2.4 APL - What's new in the Advanced Process Library V8.0?

New blocks in the Advanced Process Library for PCS 7 V8.0

AssetM

The block is used to monitor three analog process variables and reports the maintenance

status of these process variables.

CntOhSc

Combined block for recording operating hours and start-up events.

RealToDw

Block for converting a REAL number into a double word.

FbDrive

Channel block for compact drives

FbSwtMMS

Engineering Station - What's new in PCS 7 V8.0?

2.4 APL - What's new in the Advanced Process Library V8.0?

What's new in SIMATIC PCS 7 (V8.0)?

8System Manual, 12/2011, A5E02779862-01

Channel block for motor management starter

Pcs7Cntx (x=1..3)

Channel blocks for recording count values of counter modules.

StRep

Block for configuring a block group for alarm hiding.

AutoExcitation

The block is used to generate suitable trigger signals for the identification of dynamic, multi-

variable process models for a model-based predictive controller, ModPreCon.

LPOptim

Block for optimizing a linear performance function. The block is used by the ModPreCon block

for static operating point optimization.

Block extensions in the Advanced Process Library for PCS 7 V8.0

Polygon

The polygon block can be cascaded.

Event and Event_TS

The messages generated by the Event and Event_TS blocks were added to supplement the

SIMATIC BATCH information.

PidConL

Extensions to the continuous PID controller, PIDConL:

● Connection of an external control deviation

● Monitoring for the control deviation can be suppressed for a configurable period of time

following a setpoint step.

PidConR

Extensions to the continuous PID controller, PidConR

● Connection of an external control deviation

● The proportional action can be connected to the feedback.

● The derivative action can be configured for the control deviation and connected to the

feedback.

● Generation of time-stamped messages by the EventTS block.

MotSpdCL

The MotSpdCL block determines the machine and motor speed using a gear reduction factor.

RateLim

Extension of the RateLim ramp block by the "Ramp-shaped approach to a target value"

function.

Engineering Station - What's new in PCS 7 V8.0?

2.4 APL - What's new in the Advanced Process Library V8.0?

What's new in SIMATIC PCS 7 (V8.0)?

System Manual, 12/2011, A5E02779862-01 9

SelA16In

The signal selection can now be specified by an interconnectable input for the SelA16In block.

Motors, valves and dosers

● Outputs have been added to the following blocks to indicate if control and feedback match:

MotL, MotRevL, MotSpdL, MotSpdCL, MotS, Vlv2WayL, VlvL, VlvAnL, VlvS and VlvMotL.

● The following blocks now allow you to specify whether bumpless switchover should be

performed in automatic mode or via interconnection: MotL, MotRevL, MotSpdL, MotSpdCL,

Vlv2WayL, VlvL, VlvAnL, VlvMotL and DoseL.

Channel blocks

● The channel blocks support the flutter suppression function for OB82 and OB83 events of

the system blocks from the PCS 7 Basic Library V8.0.

● Detection of frozen measured values by the analog channel blocks

Extension of the gradient specification with the TimeFactor parameter

● The gradient specification for setpoints and manipulated variables has been supplemented

with the TimeFactor parameter for the following blocks: MotSpdCL, VlvAnL, OpAnL,

PIDConL, PIDConR, PIDStepL, FmCont, FmTemp

Other new features

● Limit inputs and control inputs of the blocks can now be interconnected.

● The blocks support instance-specific and parameter-specific setting of the operator

authorization level.

● In the "Out of service" mode, a feature bit can be set to determine whether active limits

should be reset or remain in effect.

● Activation of simulation mode via interconnectable inputs.

● Conditional triggering of the initial value acquisition at Intlkxx blocks.

2.5 APL - What's new in the Advanced Process Faceplates V8.0?

What's new about the block icons

Newly revised and visually-optimized V8 block icons.

● Block comments as tooltip text

● Inactive status displays of the motor and valve icons are no longer displayed.

● No display for the "On" operating mode

● Double coding of the icons for valves (rotation of the single valve icon or cross lines for a

two-way valve)

● Motors with motor signs or arrows in different directions

Engineering Station - What's new in PCS 7 V8.0?

2.5 APL - What's new in the Advanced Process Faceplates V8.0?

What's new in SIMATIC PCS 7 (V8.0)?

10 System Manual, 12/2011, A5E02779862-01

Otros manuales para SIMATIC PCS 7

Tabla de contenidos

Otros manuales de Sistema de control de Siemens

Siemens

Siemens SINUMERIK 840D sl Manual del propietario

Siemens

Siemens SIMATIC PCS 7 Guía de inicio rápido

Siemens

Siemens SINUMERIK 840D sl Guía del usuario

Siemens

Siemens QAW10 Manual de usuario

Siemens

Siemens LMV 5 Series Manual del propietario

Siemens

Siemens SINUMERIK ONE MCP 2400.c Documento técnico

Siemens

Siemens SIMATIC NET SINAUT ST7 Guía del usuario

Siemens

Siemens SINUMERIK 840D sl Manual de lista de piezas

Siemens

Siemens SINUMERIK 808D Manual de usuario

Siemens

Siemens SINUMERIK 840D Manual de lista de piezas

Siemens

Siemens SINUMERIK 828D Turning Manual de instrucciones

Siemens

Siemens SIMATIC HMI ITC1500 V3 PRO Manual de usuario

Siemens

Siemens SIMOTION P320-3 Manual de usuario

Siemens

Siemens RVW26.000B27 Manual del operador

Siemens

Siemens SINUMERIK 808D Manual de usuario

Siemens

Siemens SIMATIC NET TeleControl SINAUT ST7 Guía del usuario

Siemens

Siemens SIMATIC PCS 7 Manual de lista de piezas

Siemens

Siemens SIMATIC PCS 7 FOUNDATION Fieldbus Guía de inicio rápido

Siemens

Siemens SINAUT ST7 Guía del usuario

Siemens

Siemens SIPLUS HCS HCS PM4000 U/I Guía del administrador

Siemens

Siemens SIMATIC C7-626 Guía

Siemens

Siemens QAX850 Manual de usuario

Siemens

Siemens SINUMERIK 840D sl Manual de usuario

Siemens

Siemens SIMATIC PCS 7 Manual de lista de piezas

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario