Siemens RB500 Manual de usuario
Siemens AG
Card reader
RB500
Installation Guide
1 2 3
65
98
4
7
B0
A
RB500 EM
Book Contents
English ..........................................................3
Svenska .......................................................19
Document nr: 82336-7
Edition: 04.2010
RB500 Installation Guide 3
ENG
English
Data and design subject to change without notice.
Supply subject to availability.
© 2010 Copyright by Siemens AG
We reserve all rights in this document and in the subject thereof. By
acceptance of the document the recipient acknowledges these rights and
undertakes not to publish the document nor the subject thereof in full or in
part, nor to make them available to any third party without our prior express
written authorization, nor to use it for any purpose other than for which it
was delivered to him.
4 RB500 Installation Guide
ENG
Contents
General ........................................................ 5
Important! .............................................................................. 5
About this document ............................................................ 5
Safety ........................................................... 6
Standards & guidelines.............................. 6
Power supply .............................................. 8
Cable recommendations ............................ 8
Technical data ............................................. 9
Reading distances ................................................................ 9
General features ....................................... 10
Power Up ............................................................................. 10
Programming Mode ............................................................ 10
Timeout Period .................................................................... 10
Exit Programming Mode ..................................................... 10
Preset Congurations (short commands) ........................ 11
Installation ................................................. 12
Mechanical ........................................................................... 12
Outdoor use ......................................................................... 12
Wiring ........................................................ 14
2010 E2V Connections ....................................................... 16
2010 E2V terminal blocks ................................................... 17
RB500 Installation Guide 5
ENG
General
The RB500 can be connected to the system
product Bewator 2010 Omnis. The RB500 can be
ordered in two different variants supporting two
different reading technologies:
• Cotag technology (both active & passive)
• EM4102 technology
Important!
For proper use, this card reader needs that the
Bewator 2010 Omnis reader-node E2V has a
rmware version 4.012, or higher.
About this document
This document only serves as a Installation Guide
when using the RB500 with the main factory set-
ting and only the “short commands”.
6 RB500 Installation Guide
ENG
Safety
• Read the general safety precautions before
operating the device.
• Follow all warnings and instructions marked
on the device.
• Keep this document for reference.
• Always pass this document on together with
the product.
• The device has been approved for use in the
European Union. In countries outside the EU,
the local conditions and regulations need to be
checked before putting the device into service.
• Please also take into account any additional
country-specic, local safety standards or
regulations concerning project planning, op-
eration and disposal of the product.
• Maintenance work must only be carried out by
trained specialists.
Standards & guidelines
This product complies with the requirements of the
European Directives.
The EU declaration of conformity is available from:
Siemens AG
Siemensalle 84
D-76187 Karlsruhe
RB500 Installation Guide 7
ENG
European Directive 1999/5/EC on Radio Equip-
ment and Telecommunications Terminal Equip-
ment (R&TTE):
Compliance with the European Directive 1999/5/
EC has been proven by testing according to the
following standards:
EN 300 330-2 V1.3.1: 2006-04
EN 301 489-3 V1-4-1:2002-08
European Directive 2004/108/EC on Electro-
magnetic Compatibility (EMC):
Compliance with the European Directive
2004/108/EC has been proven by testing accord-
ing to the following standards:
EN 50130-4:1995 + A1:1998 + A2:2003
European Directive 2006/95/EC on Low-Voltage
Directive (Safety):
Compliance with the European Directive 2006/95/
EC has been proven by testing according to the
following standard:
EN 60950-1:2006
8 RB500 Installation Guide
ENG
Power supply
Any power supply connected to the RB500 must
conform to CE regulations regarding safety and
EMC.
This includes conformity to SELV (Safety Extra
Low Voltage) according to EN 60950-1.
The supply line fuse shall, independent of host
system, not in any case exceed 10A.
Cable recommendations
The cables between node and reader shall not
exceed 30 m.
RB500 Installation Guide 9
ENG
Technical data
Power supply: 12 -24 V DC
Min. 10,5 V DC
Max. 35V DC
Power consumption RB500-EM:
24V DC: Typ 17 mA (408 mW), Max*): 31 mA (744 mW)
12V DC: Typ 32 mA (384 mW), Max*): 68 mA (816 mW)
*) While horn sounds
Power consumption RB500-Cotag:
24V DC: Typ 23 mA (552 mW), Max*): 40 mA (960 mW)
12V DC: Typ 44 mA (528 mW), Max*): 90 mA (1080 mW)
*) While horn sounds
Frequency range: EM: 125 kHz.
Cotag: 66-132 kHz.
IP Class: IP54
Temperature range: -30° C to +50° C
Dimensions (HxWxD) mm: 140x80x40
If needed, complete the installation with ush mounting
kit BB3.
Reading distances
EM4102 (passive): up to 5 cm
Cotag (passive): up to 5 cm
Cotag (active): up to 10 cm
10 RB500 Installation Guide
ENG
General features
Power Up
Power up will give a rising tone from the Buzzer/
Horn. The factory setting gives that Clock&Data
conguration is selected and will work for the
Bewator 2010 Omnis. See also Preset Congura-
tion (short codes)
Programming Mode
Programming mode is enabled when powering
up the reader with the ‘B’ button pressed for 2
seconds. This is indicated by red and green LEDs
blinking.
Timeout Period
When the reader is in programming mode if no
cards are presented to the reader or short code
keys pressed the reader will automatically time out
and return to normal operation after 60 seconds.
Exit Programming Mode
Programming mode can be cancelled by press-
ing ‘B’ when red and green LEDs are ashing
together.
Tabla de contenidos
Idiomas:
Otros manuales de Lector de tarjetas de Siemens
Siemens
Siemens AR6111-MX Manual de usuario
Siemens
Siemens SIMATIC RF300 Guía del usuario
Siemens
Siemens AR10S-MF Manual de instrucciones de instalación
Siemens
Siemens Bewator PR500 Manual de instalación y operación
Siemens
Siemens PM500-Cotag Manual de usuario
Siemens
Siemens SIMATIC RF1070R Manual de usuario
Siemens
Siemens PR500-Cotag Manual de usuario
Siemens
Siemens 6FL7171-8AD Manual de usuario
Siemens
Siemens SC7 Manual de instalación y operación
Siemens
Siemens AR6181-MS Manual de usuario
Siemens
Siemens SIMATIC RF310M Manual de usuario
Siemens
Siemens SIMATIC RF650M Manual de usuario
Siemens
Siemens AR4 S-MF Series Manual de instrucciones de instalación
Siemens
Siemens AR50M-MF Manual de usuario
Siemens
Siemens AR6181-MX Instrucciones de funcionamiento y mantenimiento
Siemens
Siemens SIMATIC MV440 Manual de usuario
