Siemens Milltronics ILE-61 Manual de usuario

Instruction Manual September 2003

ILE-61

milltronics

Safety Guidelines

Warning notices must be observed to ensure personal safety as well as that of others, and to

protect the product and the connected equipment. These warning notices are accompanied

by a clarification of the level of caution to be observed.

Qualified Personnel

This device/system may only be set up and operated in conjunction with this manual.

Qualified personnel are only authorized to install and operate this equipment in accordance

with established safety practices and standards.

Warning: This product can only function properly and safely if it is correctly transported,

stored, installed, set up, operated, and maintained.

Note: Always use product in accordance with specifications.

Instruments Inc.2003.AllRights ReservedDisclaimer of Liability

This document is available in bound version and in

electronic version. We encourage users to

purchase authorized bound manuals, or to view

electronic versions as designed and authored by

Siemens Milltronics Process Instruments Inc.

Siemens Milltronics Process Instruments Inc. will

not be responsible for the contents of partial or

whole reproductions of either bound or electronic

versions.

While we have verified the contents of

this manual for agreement with the

instrumentation described, variations

remain possible. Thus we cannot

guarantee full agreement. The

contents of this manual are regularly

reviewed and corrections are included

in subsequent editions. We welcome

all suggestions for improvement.

Technical data subject to change.

MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments Inc.

Contact SMPI Technical Publications at the following address:

Technical Publications

Siemens Milltronics Process Instruments Inc.

1954 Technology Drive, P.O. Box 4225

Peterborough, Ontario, Canada, K9J 7B1

Email: techpubs@siemens-milltronics.com

For the libraryof SMPI instruction manuals, visitour Web site: www.siemens-milltronics.com

Table of Contents

ILE-61 Sensing Head ...........................................................................................................1

Specifications ......................................................................................................................2

Installation ...........................................................................................................................4

Sensing Head ........................................................................................................................................... 4

Sensing Plate............................................................................................................................................ 4

Viscous Damper....................................................................................................................................... 5

Interconnection........................................................................................................................................ 5

Non-Hazardous Unit without LVDT Conditioner Card ..........................................................5

Non-Hazardous Unit with Sensing Head Mounted LVDT Conditioner Card ..................6

Non-Hazardous and Hazardous Units with Remote-Located LVDT Conditioner Card 7

Calibration ............................................................................................................................8

General....................................................................................................................................................... 8

LVDT Output.............................................................................................................................................. 8

Zero Adjustment ............................................................................................................................8

Span Test .........................................................................................................................................9

Sensing Head Level Test .............................................................................................................9

Integrator Calibration .......................................................................................................................... 10

Maintenance and Spare Parts ........................................................................................11

Maintenance .......................................................................................................................................... 11

Spare Parts ............................................................................................................................................. 11

Unit Repair and Excluded Liability ..........................................................................................11

Inner Gasket Placement ...................................................................................................................... 12

Range Springs ...................................................................................................................13

General..................................................................................................................................................... 13

Range Spring Removal......................................................................................................................... 13

Range Spring Replacement................................................................................................................ 13

Flowmeter Recalibration ..................................................................................................................... 13

Troubleshooting .................................................................................................................14

Linearity ..............................................................................................................................15

7ML19985CX01.book Page i Thursday, September 18, 2003 12:15 PM

7ML19985CX01.book Page ii Thursday, September 18, 2003 12:15 PM

7ML19985CX01 Milltronics ILE-61 – INSTRUCTION MANUAL Page 1

ILE-61 Sensing Head

The Milltronics ILE-61 sensing head is an out-of-process sensing element for A, E, and V

Series solids flowmeters. It is used for continuous in-line weighing of powdered or

granular dry bulk solid materials. The material is directed toward the sensing plate. The

horizontal impact force of the material, deflecting the sensing plate, displaces the core of

the sensing head LVDT (linear variable differential transformer). The LVDT output signal is

proportional to material flowrate.

The ILE-61 sensing head is used with Milltronics E-300 (general purpose), A-300 (aerated

gravity conveyor), and V-300 (vertical material drop) dry solids flowmeters.

LVDT

moving beam travel

sensing plate

impact force

E-300 A-300 V-300

7ML19985CX01.book Page 1 Thursday, September 18, 2003 12:15 PM

Page 2 Milltronics ILE-61 – INSTRUCTION MANUAL 7ML19985CX01

Specifications

Operating Range

• 0 to 20 t/h (0 to 22 STPH) min., 0 to 300 t/h (0 to330 STPH) max.

Product

• fine powder to 25 mm (1")

Product Temperature

• -40 to 232 °C (-40 to 450 °F)

Ambient Temperature

• -40 to 60 °C (-40 to 140 °F)

Accuracy

• ± 1 % of full scale, higher accuracy with linearizing function of integrator

Repeatability

•±0.2%

Range Spring

• selected to suit application

Construction

• dust-tight cast aluminum frame with fiberglass rear cover

Mounting

•basemount

Sensor Type

• LVDT (linear variable differential transformer)

LVDT Excitation

• 2.50 V AC @ 2.9 kHz (supplied by Flowmeter Integrator or LVDT Conditioner Card)

LVDT Output

• 0 - 0.75 V AC @ 2.9 kHz

Damping Fluid

• 10 - 100 cm2/s (1000 - 10 000 cs) silicone, (Dow Corning 200 recommended)

Options

• Epoxy paint, synergistic polymer, or PFA coating of external aluminum casting

surfaces

• Epoxy painted mild steel or stainless steel rear cover

Approvals

•CE

• Optional CSA. Class I, Groups C and D; Class II, Groups E, F, and G

7ML19985CX01.book Page 2 Thursday, September 18, 2003 12:15 PM

7ML19985CX01 Milltronics ILE-61 – INSTRUCTION MANUAL Page 3

Sensing Plate

Construction

• 304 (1.4306) stainless steel

Options

• 316 (1.4404) stainless steel

• UHMW polyurethane or Ceramic Tile abrasion resistant lining

• Synergistic polymer or PFA coating for low cohesion and friction

LVDT Conditioner Card

Power

• ± 5 V DC (typically from Siemens Milltronics integrator)

Ambient Temperature

• –40 to 50 °C (–40 to 122 °F)

Input

• 0 to 1.0 V from LVDT

Output

• 0 to 50 mV to Milltronics SF 500 (maximum 300 m (1000 ft) separation between

Conditioner Card and integrator)

Approvals

•CE

Enclosure

• NEMA 4 (remote mounted unit)

Cable

For connection between LVDT Conditioner Card and Integrator

•Belden®

18404, 4 conductor, shielded 20 AWG (0.5 mm2) or equivalent, 150 m (500 ft)

maximum

• Belden 9260, 6 conductor, shielded 20 AWG (0.5 mm2) or equivalent, 300 m (1000 ft)

maximum

For connection between LVDT and remote LVDT Conditioner Card,

or directly between LVDT and Integrator

• Belden 8404, 4 conductor, shielded 20 AWG (0.5 mm2) or equivalent, 300 m (1000 ft)

maximum

1. Belden is a registered trademark of Belden Wire & Cable Company.

7ML19985CX01.book Page 3 Thursday, September 18, 2003 12:15 PM

Page 4 Milltronics ILE-61 – INSTRUCTION MANUAL 7ML19985CX01

Installation

Sensing Head

1. With the flowmeter housing installed, mount the ILE-61 to a rigid support structure.

2. Remove the ILE-61 fibreglass cover. With the outer gasket in place, bolt the ILE-61 to

the housing.

3. Adjust the sensing head leveling hardware (provided) to establish level in both

horizontal planes.

Sensing Plate

1. Open the flowmeter housing access door.

2. With the sensing head cover removed, remove the taper pin.

3. Insert the sensing plate shaft fully into the sensing head socket.

4. Insert the taper pin (flat side down), from the left side.

5. Tighten the right taper pin nut to lock the sensing plate shaft in place.

6. Tighten the left taper pin nut.

Note: Ensure the sensing head mounting structure is capable of supporting the

dynamic material impact forces as well as the weight of the sensing head.

Note: Ensure the sensing plate shaft is installed with the flat side up.

spirit level

rigid support

moving beam

(machined

surface)

taper pin

(flat side down)

shaft

socket

flat side up

7ML19985CX01.book Page 4 Thursday, September 18, 2003 12:15 PM

7ML19985CX01 Milltronics ILE-61 – INSTRUCTION MANUAL Page 5

Viscous Damper

1. Remove the 2 damper cover shipping screws. The damper cover will be held up by a

spring.

2. If necessary, top up the damper (to near overflowing) with the damping fluid

supplied.

3. Store the damper cover shipping screws, remaining damper fluid, and filler bottle for

future use.

Interconnection

Non-Hazardous Unit without LVDT Conditioner Card

* See note below for Encapsulated (Hazardous-rated) LVDT color codes.

Note: The damper must be full and free of air bubbles with the damper cover in

the UP position during flowmeter operation.

Note: Ground shield at Integrator only.

filler bottle

filler plug

shipping screws

damper cover

to LVDT

–

to integrator

(LVDT connection)

flowmeter

terminal

block

*For Encapsulated LVDT (hazardous)

YEL = WHITE

BLU = ORANGE

GRN = YELLOW

cable

clamp

7ML19985CX01.book Page 5 Thursday, September 18, 2003 12:15 PM

Page 6 Milltronics ILE-61 – INSTRUCTION MANUAL 7ML19985CX01

Non-Hazardous Unit with Sensing Head Mounted LVDT

Conditioner Card

• Not applicable to Hazardous-rated units

• LVDT to LVDT Conditioner Card connections are made by Milltronics

*Where separation between the integrator and LVDT conditioner exceeds 150 m (500 ft):

• Remove the jumpers SF 500 terminal 11/12 and 13/14

• Run additional conductors:

- from SF 500 terminal 12 to conditioner terminal block marked“Integrator +EXC”

- from SF 500 terminal 13 to conditioner terminal block marked “Integrator –EXC”

For further connection information on specific LVDTs, consult Siemens Milltronics.

♦Note:

1. Shields are common, but not grounded to chassis. Run cable shields

through SHLD terminals and ground at Integrator only.

2. Ensure that connection between TB 2 and TB 17 is made.

11 14 12

111

122

133

V+

S+

S-

V-

SHLD

-LOAD CELL-

EXCITATION

LCA+

LCA-

LCB+

LCB-

SHLD

LCC+ SIG

LCC- COM

LCD+ CNST

LCD-

SHLD

-LOAD CELL INPUTS-

LV D T I N TE G R AT O R

RED

BLUE

YELLOW

BLACK

GREEN

SF 500

Integrator

Milltronics LVDT Conditioner Card

LVDT

7ML19985CX01.book Page 6 Thursday, September 18, 2003 12:15 PM

Tabla de contenidos

Otros manuales de Accesorios de Siemens

Siemens

Siemens WiPS-200 Series Manual de usuario

Siemens

Siemens IR270CT Manual de usuario

Siemens

Siemens SIMATIC Vision Sensor VS 130-2 Manual de usuario

Siemens

Siemens QGO21 Series Manual del operador

Siemens

Siemens TC12 Guía

Siemens

Siemens SIMATIC RF640T Gen 2 Manual de usuario

Siemens

Siemens SITRANS TS100 Guía del administrador

Siemens

Siemens QBM97 Series Manual de usuario

Siemens

Siemens 7MH7144 Manual de usuario

Siemens

Siemens QFM2100 Manual de servicio

Siemens

Siemens SIPART PS2 Guía del administrador

Siemens

Siemens HC15 Manual de usuario

Siemens

Siemens RUGGEDCOM WIN7025 Manual de usuario

Siemens

Siemens SITRANS FC430 Guía de inicio rápido

Siemens

Siemens HL 3000 Manual de usuario

Siemens

Siemens SITRANS F M MAG 1100 Manual de usuario

Siemens

Siemens SITRANS WW300 Manual de usuario

Siemens

Siemens GAMMA instabus 5WG1 211-2DB01 Manual de servicio

Siemens

Siemens SITRANS WS300 Manual de servicio

Siemens

Siemens QAA4292.EWSC Manual de usuario

Siemens

Siemens SITRANS LG240 Manual de usuario

Siemens

Siemens SITRANS WW100 Manual de usuario

Siemens

Siemens Desigo QMX3.P44 Manual de usuario

Siemens

Siemens Milltronics RBSS Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario