Siemens HL 3000 Manual de usuario

Your

eye

in

hell

HL 3000 Manual

© Siemens Laser Analytics Sept 2000

Halogen lamp alignement manual

Document number: CID 3002-1103 Rev. 1A

LDS 3000 Operators manual HL 3002

1

1. HL 3002

1.1 General

Sometimes the visibility in the measurement path is poor. The reason for

this might be high dust load, smoke or strong ambient light from the

process (as in a combustion chamber). In this case a stronger light source

must be used in the first alignement step. Siemens Laser Analytics AB

can supply a suitable light source labelled HL 3000. This is a point source

using a 50 W halogen lamp and will produce a very luminous light spot -

normally easy to spot in the alignement procedure.

HL 3002 LDS 3000 Operators manual

2

1.2 The alignement procedure

The sensor is aligned using the sensor alignment kit AK 3002 together

with HL 3000. The aligning procedure is as follows:

Receiver side

1. Start by aligning the transmitter side. This is done by removing the

receiver at the quick connect interface and instead mount HL 3000

which defines the optical axis of the sensor pair. While the receiver is

dismounted - check that the lens is clean on the receiver and that the

purging is working.

Receiver side

HL 3000 generates a considerable amount of heat. Protective gloves should be ised

when it is handled.

Halogen alignement lamp

Note!

LDS 3000 Operators manual HL 3002

3

Transmitter side

2. Dismount the transmitter and check that the lens is clean on the

transmitter and that the purging is working. Then mount the trans-

mitter and twist-dismount the launcher (fiber cable connector in the

middle), twist-mount the cross hair instead. Align with the four bolts

on the flange, the light dot must be centred in the inner ring of the

cross hair.

Transmitter side

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

4

Transmitter side

3. Twist-mount the alignement lamp instead of the cross hair in the

transmitter.

Transmitter side

Alignement lamp

LDS 3000 Operators manual HL 3002

5

Receiver side

4. Mount the receiver back again and twist-mount the cross hair

instead of the detector module. Align with the four bolts on the

flange, the light dot must be centred in the inner ring of the cross

hair.

Receiver side

CD 3002 is now aligned and the holder for the fibre connector and the de-

tector module should be mounted in their places.

Finally, instrument air, or which ever method is used to protect the opti-

cal surfaces, should be connected to the appropriate inlets both at the

transmitter and receiver side of the sensor.

The mechanical stability of the sensor mechanics is sufficient to allow

dismounting (the quick connection) of both the receiver and the trans-

mitter. This means that cleaning of the lenses does not require re-align-

ment of the sensor.

Cross hair

Alignement screws

HL 3002 LDS 3000 Operators manual

6

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Otros manuales de Accesorios de Siemens

Siemens

Siemens 8WD44 Manual de usuario

Siemens

Siemens TA1Q300 Manual de usuario

Siemens

Siemens SIWAREX WL200 Series Manual de usuario

Siemens

Siemens 7MH7144 Manual de usuario

Siemens

Siemens milltronics MFA 4P Manual de usuario

Siemens

Siemens SIMATIC VS 110 Manual de usuario

Siemens

Siemens QFM3100 Manual de servicio

Siemens

Siemens SITRANS F C MASS 2100 DI 1.5 Manual de usuario

Siemens

Siemens Symaro QAA2890/WI Manual de usuario

Siemens

Siemens SIMATIC Vision Sensor VS 130-2 Manual de usuario

Siemens

Siemens SIMATIC RF640A Manual de usuario

Siemens

Siemens 1218RF Manual de usuario

Siemens

Siemens SITRANS FC430 Guía de inicio rápido

Siemens

Siemens SIMATIC RF640T Gen 2 Manual de usuario

Siemens

Siemens TC12 Guía

Siemens

Siemens SITRANS WS300 Manual de usuario

Siemens

Siemens enlighted SU-5i-USB Manual de usuario

Siemens

Siemens RUGGEDCOM WIN7225 Manual de usuario

Siemens

Siemens AP 257/41 Manual de usuario

Siemens

Siemens QAF63 Series Manual de instrucciones

Siemens

Siemens QPM11 Series Manual de usuario

Siemens

Siemens ADM-QXA12T Manual de usuario

Siemens

Siemens SITRANS TS100 Guía del administrador

Siemens

Siemens ADM-Q12 Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario