Siding Tools Industries UK-12 Manual de usuario
Trancheuse pour
revêtement mural
de 12
"
MANUEL D’UTILISATION
12" Siding shear
OWNER’S MANUAL
AVERTISSEMENT
Lire et Comprendre toutes les
directives. Le non-respect des directives
décrites ci-dessous peut causer des
blessures graves.
VEUILLEZ CONCERVER CES
DIRECTIVES POUR REFERENCE
ULTERIEURE.
WARNIG
Read and understand all
instructions. Failure to follow all
instructions listed below may
result in serious bodily injury.
SAVE THESE
INTRUCTIONS FOR
FUTURE REFERENCE
UK-12
-1-
SAFETY RULES FOR THE 12" SIDING SHEAR
1. READ AND UNDERSTAND THIS INSTRUCTION MANUALBEFORE
OPERATINGTHE12"WALL COVERING CUTTER.
2. The 12’’ Siding Shear comes with a 1 year warranty. To activate your
warranty, we invite you to register on our website in the service tab at :
sidingtoolsindustries.com
3.
If you are not thoroughly familiar with the operation of the 12" Wall
Covering Cutter,obtainadvicefromaqualifiedworkerorcall450-527-
7840
4.
Stay alert. Do not operate while under the influence of drugs, alcohol, or
medication.
5.
Alwayswearsafety approvedeye protectionwith sideshields(ANSIZ87.1)
6.
Keepwork areaandfree of debris.
7.
Keepchildren andunauthorized persons away from the 12" WallCovering
Cutter and workarea.
8.
Make sure tool is secure. Operate only on a firm substrate or solid stand.
9.
Use the right tool. Do not force the 12" Wall Covering Cutter or use it for a
job for which it was not designed; use only on approved materials.
10.
Keep blade sharp. A dull blade will not perform properly.
11.
Always keep hands away from blade while operating or carrying.
12.
Do not alter or misuse this tool. The 12" Wall Covering Cutter is
precision built; modifications not specified in this manual may result in
a dangerous condition.
13.
Maintain the 12" Wall Covering Cutter with care. Keepblade sharpand
clean. Follow instructions for lubricating and changing accessories.
14.
Useonlyrecommendedaccessories.Theuseofimproperaccessoriesmay
causehazardsorinjury.
15.
Never leave the 12"Wall Covering Cutter unattended. Secure the handle
with the safety lock when not in use.
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS
INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL
CONSIDERABLY LESSEN THE POSIBILITY OF PERSONAL INJURY.
SET UP
-2-
Installation of the Cutter
Install
the front cross bar to the cutter base
with the two bolts and nuts
provided, as
shown.
Warning:
Do not put your fingers
against the sharp edge of the blade
at any time.
CUTTING
-3-
Cutting Preparation
Detach the safety clip from the
handle.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
Cutting Preparation
Secure the blade to lock the
mechanism.
Lift the handle and position the
blade in the locked position
Warning:
Do not put your
fingers against the sharp edge
of the blade at any time.
Cutting Preparation
The mechanism is locked when the
pivot is raised upwards as shown in
the picture. To do this, raise the
handle to its highest and manipulate
the pivot manually
Warning:
Do not put your
fingers against the sharp edge
of the blade at any time.
CUTTING
-4-
Cutting Preparation
Slide the profile into the
predefined block for the type of
profile to be cut. Put the blade in
the cutting position by raising the
handle very high to unlock the
mechanism, then down the handle
to cut.
Warning:
Do not put your
fingers against the sharp edge
of the blade at any time.
Cutting Preparation
Before cutting, reposition the pivot
downwards in the working
position. To do this, raise the
handle to its highest and
manipulate the pivot manually.
Warning:
Do not put your
fingers against the sharp edge
of the blade at any time.
-5-
MAINTENANCE
Maintenance
For any service, it is recommended to
contact Siding Tools Industries at 450-
527-7840
Warning:
It is recommended to
lubricate the blade on a regular
period of time with PL-100 or
equivalent. Do not use WD-40.
Block change according to the material
to cut
Keep the slicer closed. Remove the 4
screws from the bottom of the base.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
Block change according to the material
to cut
Disengage the pivot pin. Raise the handle
and the blade to clear the block
completely.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
-6-
MAINTENACE
Block change according to the material
to be cut
Clear the block completely. Hold
or attach the blade holder to
secure it in the raised position.
Remove the blocks. Position
another block according to the
material to cut. Screw the 4
screws lightly.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
Block change according to the material
to be cut
Lower the blade to the cutting
position to validate the alignment
of the block. Tighten the 4 block
fixing screws.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
Block change according to the material
to be cut
Re-engage the pivot pin.
Warning:
Perform a cut test
before proceeding to validate the
alignment of the blade with the
block.
-7-
MAINTENACE
Blade lade change
Disengage the pivot pin. Raise the handle
and the blade to clear the block
completely.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time.
Blade change
Clear the block completely.
Remove the 4 bolts to remove the
blade. Position the new blade and
slightly refit the 4 bolts.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time
Blade change
Lower the blade to the cutting
position to confirm the alignment
of the blade. Tighten the 4 bolts.
Warning:
Do not put your fingers
against the sharp edge of the
blade at any time
-8-
MAINTENACE
Block change according to the material
to be cut
Re-engage the pivot pin.
Warning:
Perform a cut test
before proceeding to validate the
alignment of the blade with the
block.
Transport
Attach the safety clip to the
handle. If the tie is in good
condition, you can lift the shear by
the handle. If not, it is advisable to
raise with two hands by the base.
The weight of the shears is about
55lbs.
Warning:
Secure the safety clip.
For transport by lifting the base,
pay attention to the tip of the
blade protruding at the front.
-9-
OVERAL DIMENSION
Tabla de contenidos
Idiomas:
Otros manuales de Cortador de Siding Tools Industries
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
