Sicon EVMS Series Manual de usuario

Electric Vehicle Charging Station

EVMS-150

2021 V1.0

USER MANUAL

Content

PART 1 Safety Instruction ..................................................................................................................3

1.1 General Instruction .............................................................................................................3

PART 2 EVMS-150 Charger Installation............................................................................................5

2.1 transport .............................................................................................................................5

2.2 Charger Receiving Inspection...........................................................................................5

2.3 Charger Storage...................................................................................................................6

2.4 Installation environment.....................................................................................................6

2.5 Unboxing .............................................................................................................................7

2.6 Position................................................................................................................................8

PART 3 Introduction and installation of charge ............................................................................10

3.1 Product Overview..............................................................................................................10

3.2 Feature ..............................................................................................................................10

3.3 Outline Dimension ............................................................................................................11

3.4 Appearance .......................................................................................................................12

3.5 Charger dust screen and air inlet and outlet.....................................................................14

3.6 Charger diagram................................................................................................................17

3.7 Input Connection Terminals ..............................................................................................18

3.8 Install and remove the main power module.....................................................................19

3.9 After the initial setup boot................................................................................................20

3.10 Charging status indicator.................................................................................................20

3.11 Emergency stop button...................................................................................................20

3.12 Charger connector bin.....................................................................................................21

3.13 RFID Card reader .............................................................................................................21

3.14 Charging strategy ............................................................................................................21

3.15 Charger parameters. .......................................................................................................22

PART 4 Product Overview ..............................................................................................................23

4.1 Module Introduction .........................................................................................................23

4.2 Appearance .......................................................................................................................23

4.3 Feature ..............................................................................................................................25

4.4 Module diagram................................................................................................................25

4.5 Specification ......................................................................................................................26

PART 6 Charging Operation............................................................................................................27

6.1Charging Flow Chart...........................................................................................................27

6.2 Charging process ...............................................................................................................28

PART 7 Enter the administrator interface .....................................................................................29

7.1 How to enter the administrator interface.........................................................................29

7.2 Each unit described ...........................................................................................................30

PART 8 Troubleshooting.................................................................................................................31

PART 1 Safety Instruction

1.1 General Instruction

Operating at AC mains high voltage, the charger is composed of high current/voltage withstanding

components. Proper installation of the charger to be grounded to defense electric shock and

foreign objects. Installation service should be performed by qualified technician or authorized

service partner of the manufacturer.

WARNING!

Operations inside the charger should be performed by qualified

technician or authorized service partner of the manufacturer.

1.1.1Symbols introduction

WARNING!

Warning

Refer to the manual for more information.

Danger

There is risk of electric shock, the charger has high voltage.

NOTE!

Note

Read this information to avoid damage to the charger.

1.1.2 Grounding symbol

Protective grounding wire

Grounding terminals must be connected before making other

connections to the charger.

1.1.3 Safety notes

1) Please carefully follow the safety instructions to keep the electric car out of danger;

2) Before charging, check the charger touch screen and indicator light. If there’s fault, the fault

must be solved before using the charger to charge.

3)Before the charger starts charging, make sure that the Electric car is in power off state;

4) Completely follow the text prompts to conduct charging process.

5) It is prohibited to unplug the charging connector during charging process to prevent Any

kind of unwanted accident and ensure safety;

6) The entire charging process is completely automatic, EVMS-150 will shut down by itself

while it finishes charging the car. The charging process don’t need any human intervention but we

recommend regular inspection to check if there’s any abnormal situation,

7) When not in use, try to avoid direct exposure of the tip of Charging connector, and plug it

back into the socket to prevent damage. Check the charging cable or charging tip if the shell is

damaged, exposed cables and other problems, please stop using until fixing it t;

PART 2 EVMS-150 Charger Installation

2.1 transport

Note: The center of gravity of the equipment is not in the center. When using a forklift to

unload and transport, please fork in the direction as shown in the figure to prevent the

equipment from tipping over.

sketch map

Transport, road transport choice, should choose a better road traffic, to prevent

excessive turbulence can also choose rail transport and water transport.

2.2 Charger Receiving Inspection

When receiving the charger, please carefully check the box and the charger whether there are

any signs of physical damage. The logo on the box should be complete. If there is a rupture or

suspected rupture, please inform:

* Carrier

* Manufacturer

NOTE!

Visible Transport Damage must inform the carrier immediately upon

receipt of the goods!

Other transport damage must also be declared immediately and the

carrier must be notified within seven days of receiving the equipment.

The packaging material should be kept for later inspection.

2.3 Charger Storage

If the charger is not to be installed immediately it must be stored in stable position, and in a certain

temperature and humidity environment, the environmental conditions are as follows:

Temperature : -25°C to 60°C

Relative humidity: ≤95%, non-condensing

The recommended storage temperature is between: 10°C to 30°C.

2.4 Installation environment

To ensure the safe and healthy use of the charger, the location should be appropriate. Not only to

maintain a clean working environment, avoiding moisture, flammable gases, flammable liquids or

corrosive substances; users can place them at designated locations by means of manpower or

equipment, but be careful to maintain the spacing around the charger, to facilitate air circulation

and heat dissipation.

The following points should be noted:

A minimum of one meter of space must be left in front of and behind the machine to ensure

adequate space for operation and maintenance.

The input cable for the AC enters from the bottom of the charger.

Input and output wiring check

To ensure the safety of personnel during the installation of the charger, it is important to ensure

that all connections are made in the following conditions:

●Keep EVMS-150 installation area clean and dust free

● All power cables are Proper length and diameter

●Startup and operational checks are performed by authorized service personnel.

●Confirm the input and output voltage and frequency of the charger

●Ground connection in accordance with IEC standards or local regulations.

Installation environment

●Sufficient ventilation distance should be maintained on all sides of the charger case

●Away from heat and corrosive substances, avoid direct sunlight

●Maintaining normal operating temperature and altitude; Working temperature: -20 ℃~ 60 ℃

2.5 Unboxing

Vertical steel edge wooden packaging

Horizontal detachable packaging

Disassembly and assembly are carried out in the horizontal state:

Use a flat-blade

screwdriver to open it to

remove the wooden box

Use the open spanner SJGJ-17-19 to disassemble and assemble the bolts and washers in

the blue frame line as shown in the figure, each with 40 pcs.

Save the bolt, washer, and the honeycomb inner corner removed, according to the

position of the mounting place when unpacking the package again.

2.6 Position

In order to ensure smooth and reliable charger, the charger must be vertical basic construction

charger mounted on cement concrete cement based on custom and mounted above the base

level of the ground is not less than 220mm,.

Drilling template according to claim 6 Drill hole depth of 12mm in diameter 100mm in a cement

base, and then through the wall portion of the expansion bolt is inserted in a hole drilled;

Charging the cement foundation piles and reliable ground connection, the ground resistance

must ≤4Ω.

Before installing the charger, it should be checked as follows: the

device is damaged, if damaged, the shipper immediately; product

label check, confirm the correctness of the device. The equipment

label is affixed to the equipment, and the model, capacity and main

parameters are indicated on the label.

Front

Remove the anti-vibration components at the bottom of the cabinet, and then use a crane

(recommended) or a forklift to move the cabinet to the installation location on the concrete

foundation.

NOTE!

1. The lifting equipment used to carry the charger must have sufficient lifting

capacity.

2. When removing the loaded pallet, ensure that there is sufficient manpower

and lifting equipment.

3. The charger has a high center of gravity, so be careful to tip over.

Base anchoring hole diagram

PART 3 Introduction and installation of charge

3.1 Product Overview

EVMS series Electric Vehicle charger station is an intelligent integrated DC charging station system

promoted meet market demands. It adopts modular concept and cutting-edge electronic circuit

technology, integrating power conversion, charge control, management, query, display and

background communication in one cabinet. By communication with the BMS of electric vehicles,

to achieve intelligent control of the entire charging process. It is composed of Human-machine

Interaction Unit, Control Unit, Charging Module unit, Measurement Unit and Protection Unit. The

design conforms to EN61851, EN62196, DIN70121, CHAdeMO1.2 and other standards.

3.2 Feature

The charger supports CCS2 connectors could be used simutaneously.

Built-in power meter with charging power metering function.

Configured with DPM1000/30 charging modules.

Support RFID Card charging(Mobile app optional) , support reservation function.

widescreen TFT touch screen with good human-machine interface, which can display QR code,

status information, metering information, alarm, charging records, etc.

LED indicators of power, charging status and fault.

Self-identifying electric vehicle BMS protocol function, mufti-models compatible charging;

Emergency stop button can cut off the charger output in urgent situations.

protection, AC input over voltage protection, AC input under voltage protection, short circuit

retraction protection, DC output over voltage protection, DC output under voltage protection,

battery anti-reverse protection, current anti-reverse and other protection functions;

Charging process protection function, when it occurs BMS communication failure,

disconnection, battery temperature, voltage exceeds the allowable limit, etc. During charging

process, the charge will immediately stop charging;

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario