SI TRO.Y Instrucciones de funcionamiento
DOC.#400114
TRO.Y
Programming Guide
®
2
Somfy®, UAI+™, and SDN are copyrighted and owned by Somfy Systems Inc. and are used in this
document with permission and are in full compliance with the June 2016 Somfy Trademarks, Logos
and marketing Assets Guide and Use Agreement.
All product names, logos, and brands are property of their respective owners. All company, product
and service names used in this document are for identification purposes only. Use of these names,
logos, and brands does not imply endorsement.
Copyright©2018, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball
logo, 4Store, 4Sight, Control4 My Home, Mockupancy, BakPak, Pakedge, Pakedge TruStream,
SmartWav, StealthPorts, and Triplex are registered trademarks or trademarks of Control4
Corporation or its subsidiaries in the United States and/or other countries.
2021 Copyright©US SCREEN CORPORATION
3
Table of Contents
TRO.Y Setup Procedure 5
Connection Status Types 9
Introduction 4
General Procedure Overview 4
Web browser interface etiquette 6
Home Menu 7
Dashboard 8
Firmware 10
System Settings 12
Integration Settings 13
Integration Table 16
Device Integration Table 17
485 Device Discovery 18
Device Configuration 19
485 Motor Configuration 20
RTS Receiver Configuration 23
485 Keypad Configuration 24
Keypad Comand List 26
Keypad Sequence 27
Groups 28
Super Groups 29
Broadcast Alias 30
Telnet Client Table 31
Special Groups 32
Reports 32
Programming Troubleshooting 33
Future TRO.Y Firmware releases 34
4
This guide is intended to provide step-by-step instructions to commission a TRO.Y as a central
controller for any Screen Innovations shade/screen products.
Note: If your project contains any Zigbee or RTS motors, you must complete your configuration
using the TaHoma app with your TaHoma/LinkPro Z.
Before binding any RTS products to a TaHoma or LinkPro Z, all RTS products must be fully
commissioned. Up end limits, down end limits, “my” positions, and group hand controls (Situo
remotes, DecoFlex switches, etc) must all be fully configured.
1. Connecting your TRO.Y to a PoE switch or a PoE injector
2. Discover the TRO.Y on the network
3. Create a TRO.Y account by selecting a system password
4. Configuring TRO.Y system, integration settings
5. Test and verify
www.screeninnovations.com | 512.832.6939 | Doc.#110-104a | Version 0.0.3 | 07/08/2019
Introduction
General Procedure Overview
5
TRO.Y Setup Procedure
Before starting the setup process, unbox the TRO.Y unit and connect the PoE switch or connect
to PoE injector. Verify the status LED light on TRO.Y is solid red.
1. Using a standard web browser, lets connect to TRO.Y
a. Use one of the following methods to determine TRO.Y’s IP address:
- DHCP server
If you have access to your DHCP server, locate the MAC address on the label of the
bottom of TRO.Y. All TRO.Y units MAC address will start with “70:B3:D5”
- Windows Console
Using the windows search command, type in “CMD”,
then click to open the command prompt, next type
“arp-a”. Review the list untill you find your TRO.Y’s MAC
address.
- Using universal plug-n-play
Open file explorer and click on the network icon. TRO.Y
is listed in “Other devices” in network devices.
- Now you can double click the TRO.Y icon to bring up the web browser OR
- You can right click the TRO.Y icon to bring up the TRO.Y properties including the IP
address
www.screeninnovations.com | 512.832.6939 | Doc.#110-104a | Version 0.0.3 | 07/08/2019
6
As with any web browser interface, refrain from using the standard back and forward buttons as
you can lose data that has not been saved or sent to TRO.Y. The refresh button is ok, but you can
lose data that has not been saved or sent to TRO.Y on the current page.
Web browser interface etiquette
7
Home menu has 5 selections:
- Dashboard – This is an information only page that shows
your current Wireless, Telnet Server, and Telnet Client
statues and any configured 485 devices that may be offline
and you will need the system password to proceed to any
other pages (if setup)
- Integration Table – This selection requires a valid password and provides access to the Device,
Group, Telnet Client, and Super Group tables
- Integration Settings – This selection requires a valid password and provides access to the Telnet
server, Telnet Client, Serial Control, and Wireless Bridge configuration settings
- System Settings – This selection will allow you to create a system password, adjust and view the
TRO.Y unit IP settings and update firmware
- Reports allow you to create Integration reports and soon site files
www.screeninnovations.com | 512.832.6939 | Doc.#110-104a | Version 0.0.3 | 07/08/2019
TRO.Y Data storage
Home Menu
8
- Now use a browser and navigate to the TRO.Y IP
address found using one of the previous methods
listed on pg. 4
- If this is the 1st time, you are accessing TRO.Y no
password has been created yet. See pg. 8 on how
to setup a password. If a password has already been
created, you must enter it in order to get that into
any of the menus.
- If you have forgotten the password,
pressing the reset button once on the
TRO.Y unit will allow you to bypass the
password for 5 minutes.
Dashboard
9www.screeninnovations.com | 512.832.6939 | Doc.#110-104a | Version 0.0.3 | 07/08/2019
Connection Status Types
- Telnet Server Connection – will show the
current connection or configuration status
- Wireless Bridge Connection – will show the
current connection or configuration and
authentication status
- Telnet Client Connection – will show the
current connection or configuration status
- 485 Devices offline – show all the currently
configured 485 devices that are currently offline
- Refresh – Click this button to update the Connection status
Connection status types
Check Ethernet connection, IP and subnet address(es)
Current connection is good
Disabled in the Integration Settings Menu
Performing 485 Discovery
Connection is ok, but settings are not authenticated or are not at
the currently set IP address(es) in the integration Settings menu
Connection status
10
- TRO.Y ships from factory with firmware version 1.4
- SI recommends to always update TRO.Y to the latest firmware version
- You can find the latest version in the TRO.Y resource section under firmware at the screen
innovations support website https://support.screeninnovations.com/accessories/kratos/
- TRO.Y firmware will have an extension of ###.troy. Using the “choose file” button to browse
the location where you downloaded the file on your device. Press reset button once, until the
status LED is flashing Red. Select submit to send the firmware update to TRO.Y
- TRO.Y will acknowledge the firmware update was received and you can now perform a reboot
from the settings page, or by pressing the reset button for 10 seconds, or by removing the PoE
power and then re applying the PoE power to TRO.Y
- TRO.Y will now reboot, load the new firmware and is now ready to continue your setup
Firmware
Otros manuales para TRO.Y
1
Tabla de contenidos
Otros manuales de Puerta de SI
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
