Si Tech GCS900 Manual de usuario
Field Reference Guide
SITECH TECHNOLOGY DEALER
Page #
3
4
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Table ofContent GCS900 GRADER
Version: 13.1
Table of Contents
CB460 Control Box Layout
Grader Training Display Settings
Sensor Calibration Test
Check Blade Wear
Load Design
Verify System Accuracy
Vertical Offset
Horizontal Offset
Vertical Guidance
Cut and Fill Site Map
Lane Guidance
GPS + Sonic Set-Up
UTS Set-Up
UTS +Sonic Set-Up
Sensor Calibration
Lift Valve Calibration
Side Shift Valve Calibration
Connect to Wi-Fi
TCC Settings
Configure Remote Assistant
Wireless Data Sync
Start Remote Assistant
Connect toIBSS Base GCS900
27
Field Reference Guide
SITECH TECHNOLOGY DEALER
Power Menu USB Port Enter
Next Key
Escape / Go Back
Cut / Fill Right
Function Keys (F1-F6) Zoom In - Out
Cut / Fill Left Horizontal Guidance
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Grader Training Display Settings
Version: 13.1
The Control Box must be in Manager’s Mode
1. Press “Menu”
2. Select “GNSS Accuracy” and Press “OK”
3. Press and Hold “F6 ” and Press “F2” Medium Mode
4. Change “GPS Horizontal error limit:” to “0.30ft or 0.090m” and Press “Next”
5. Change “GPS Vertical error limit:” to “0.30ft or 0.090m” and Press “OK” Twice
6. Select “Guidance Method” and Press “OK”
7. Use Arrow to change Adjust cut to avoid overcut: to “NO” and Press “OK”
8. Select “Increment Switch Adjustment” and Press “OK”
9. Change Vertical offset increment: “0.00” and Press “OK”
10. Select “Text Items” and Press “OK”
11. Press “F1” and Uncheck each Item checked
12. Press “F1” to select “Cut/Fill Left”,“Station” and “Cut/Fill Right” (select in order)
13. Press “F3” Cross-Section
14. Press “F1” and Uncheck each Item checked
15. Press “F1” to select “Cut/Fill Left”,“Station” and “Cut/Fill Right” (select in order)
16. Press “F4” Profile View
17. Press “F1” and Uncheck each Item checked
18. Press “F1” to select “Cut/Fill Left”,“Station” and “Cut/Fill Right” (select in order)
19. Press “F5” Text View 1
4
20. Press “F1” and Uncheck each Item checked
21. Press “F1” to select “Design Elev.(3D)”,“Design XSlope (3D)”,“Design Mainfall (3D)”
“Satellites (3D)” and ”V. GNSS Err (3D) (select in order)
22. Press “F6” Text View 2
23. Press “F1” and Uncheck each Item checked
24. Press “F1” to select “Northing (3D)”,“Easting (3D)”,“Elevation (3D)”,“Cross Slope” and
“Mainfall” (select in order)
25. Press “OK”
26. Select “Save Settings” and Press “OK”
27. Select “Display Settings” and Press “OK”
28. Enter Operator’s Name such as “Joe G” and Press “OK”
29. Press “ESC” twice to return to operating screen
5
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Grader Sensor Calibration Test
Version: 13.1
1. Move Grader to a hard flat surface (concrete or asphalt is preferred)
2. Square Blade to and mark ground at each Blade Tip
3. Press “Next” until Cross Slope (%) is displayed
4. Square Blade to Chisel Marks
5. Lower the blade to the ground and float the hydraulics
6. Record Cross Slope (%)
7. Rotate Blade to the right approx. 30° and float the hydraulics
8. Rotate Blade to the left approx. 30° and float the hydraulics
9. Turn Grader around and repeat the 3 positions
10. Cross Slope accuracy should match readings within +/- 0.2%
If the readings are greater than +/- 0.2% a new Sensor Calibration is required
6
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Check Blade Wear
Version: 13.1
1. Press “Menu”
2. Select “Blade Wear” and Press “OK”
3. Measure from Center of Cutting Edge Bolts to Bottom of Blade
4. Do not use Bolt at Blade Tip
5. Enter Distance and Press “OK”
6. Press “ESC” to return to operating screen
7
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Load Design
Version: 13.1
1. Press “Menu”
2. Select “Select Design” and Press “OK”
3. Use Arrows to highlight Design and Press “OK”
4. Press “ESC” to return to the operating screen
8
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Verify Grader System Accuracy
Version: 13.1
Verify the system accuracy at the start of each work day using a Permanent Bench Point
1. Move machine to Bench Point with the Blade low to the ground
2. Position Blade Tip over Bench Point
3. Press “Next” until Text Screen 2 is displayed
4. Verify correct Blade Tip is selected Press “F1” to change Blade Tip
5. Verify Northing, Easting and Elevation are correct (add distance above Bench Point)
6. See Supervisor if Northing and Easting do not match
7. See Supervisor if Elevation does not match Press “Next”
9
Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Vertical Offset
Version: 13.1
1. Press “F4” to enter Horizontal and Vertical Offset
2. Press “F6” until Vertical Offset is displayed at the top left of screen
3. Enter Vertical Offset and Press “F2” to select above or below Design
4. Press “OK” to return to operating screen
5. Vertical Offset is displayed at the bottom of the screen
10
Otros manuales para GCS900
1
Tabla de contenidos
