Shuttle HOT-595 Manual de usuario

HOT-595

Pentium™processor

Based AGPMAINBOARD

User's Manual

NOTICE

AllRightReserved

Manual Ver 1.0

Allinformation, documentation, andspecifications contained inthis manual aresubject to changewithout prior

notificationbythemanufacturer.

The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a

commitment to update the information contained herein.

TRADEMARKS

All the brands and product names referred to in this manual are trademarks or registered trademarks of their respective

holders.

FCC Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy. If not installed and used properly, in strict accordance

with the manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures :

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help and for additional suggestions.

The user may find the following booklet prepared by the Federal Communications Commission helpful "How to Identify and

Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Office. Washington,

DC 20402, Stock 004-000-00345-4

FCCWarning

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the users authority

to operate this equipment.

Note: In order for an installation of this product to maintain compliancewith the limits for a Class B device, shielded cables

and power cord must be used.

CE Notice:

Following standards were applied to this product, in order to achieve compliance with the electromagnetic compatibility :

- Immunity in accordance with EN 50082-1: 1992

- Emissions in accordance with EN 55022: 1987 Class B.

TABLE OF CONTENTS

PREFACE ........................................................................................................................3

CHAPTER 1 FEATURES ......................................................................................................4

Accessories of HOT-595 .......................................................................................................................... 6

CHAPTER 2HARDWARE CONFIGURATION.............................................................................7

Jumper Setting........................................................................................................................................... 7

CPUClock Configurations -DIP Switch SW2........................................................................................ 8

SystemClock and CPUMultiplier Setting Manually- SW2 ................................................................ 12

CPUVoltage Setting Manually - SW1................................................................................................... 13

CPUBurst Mode Jumper-JP3................................................................................................................ 14

Flash EEPROM Vpp - JP13................................................................................................................... 14

ClearCMOS -JP6................................................................................................................................... 14

Connectors............................................................................................................................................... 15

CHAPTER 3MEMORY CONFIGURATION ..............................................................................14

CHAPTER 4 FLASH UTILITY .............................................................................................18

CHAPTER 5 VIA VXD AGP DRIVER INSTALLATION ............................................................20

CHAPTER 6 BIOS SETUP ...............................................................................................23

MainMenu .............................................................................................................................................. 24

StandardCMOS Setup............................................................................................................................ 26

BIOS Features Setup............................................................................................................................... 28

Chipset Features Setup............................................................................................................................ 30

PowerManagement Setup ...................................................................................................................... 32

PCIConfiguration Setup......................................................................................................................... 35

Integrated Peripherals ............................................................................................................................. 38

PasswordSetting ..................................................................................................................................... 41

HOT-595mainboard isa highly integrated IBM PC/AT compatible ATX form-factor system

boarddesigned to meet the industry's most demanding desktop applications. Based on the

VIA'sVP3 chipset.

HOT-595accept AMD K5, K6, Intel Pentium P54C, Pentium MMX, IDT-C6 and Cyrix/

IBM6x86, 6x86L, 6x86MX processors and also featureshigh-performance pipelinedburst

secondarycache memory support with size of 1024KB or 512KB. The memory subsystem

isdesigned to support up to 384 MB of EDO RAM andSDRAM inthree 168-pin 3.3 V

DIMMsockets.

HOT-595is equipped withan Accelerated GraphicsPort (AGP) slot,a high performance

interconnectfor graphic-intensiveapplication, suchas 3Dapplications. The AGPis inde-

pendentof the PCIbus andis designed toexclusively use with graphical-display devices.

HOT-595provides a new level of I/O integration. VIA VP3 chipset provides increased

integrationandimprovedperformance over other chipsetdesigns.

TheVIA's VP3 chipset provides an integrated Bus Mastering IDE controller withtwo high

performanceUltra 33DMA IDE interfaces for up to four IDE devices.

TheonboardI/Ocontrollerprovides the standard PCI/Ofunctions:floppyinterface, two

FIFOserial ports,an IrDAdevice portand aSPP/EPP/ECP capableparallel port.

Upto fourPCI localbus slots provide a high bandwidth data path for data-movement

intensivefunctions suchas graphics,and up to three ISA slots complete the I/O function.

HOT-595provides the foundation for cost effective, high performance, highly expandable

platforms,which deliver the latest in Pentium processor and I/O standard.

HOT-595Mainboard is carefully designed for the demandingPC user who wants high

performanceand many intelligentfeatures in acompact package:

PREFACE

FEATURES

Chipset

FeaturesVIA's 82C597VP3 AGP Chipset with I/O subsystems

MainProcessor

AMD K6 166~266 MHz, K5 PR75~PR166,

IntelPentium (P54C) 75~200 MHz, Pentium MMX (P55C) 166~233MHz,

Cyrix/IBM6x86 P120+~P200+,6x86L P200+,6x86MX PR166~PR233,

IDT-C6150~200MHz

SecondaryCache

Onboard1024KB or512KB PipelinedBurst Cache

VersatileMemorySupports

Equippedwith three DIMM sockets for (8, 16,32, 64or 128MB) 168-pin SDRAM memory

modulesup to 384 MB

ExpansionSlots

One AGP slot

FourPCI slot

Three ISA slot

AGPSupport(AcceleratedGraphicsPort)

HOT-595main boardequipped withan AGPslot foran AGPVGA cardthat supports133MHz

2Xmode for texture mapping z-buffering and alphablending. AGP allows3D applications to run

faster and smoothly.

OnboardI/O Chip

One Floppy port

One PS/2 mouse and Keyboard connector

Two high-speed UART compatible serial port

SerialPort 2 can also be directed fromCOM2 tothe Infrared Module for wireless connections

Oneparallelportwith ECP and EPPcapabilities

OnboardPCI Bus MasterIDE Controller

TwoUltra DMA/33 Bus Master IDEPorts supportsfour IDE devices up to33 MB/sec

IDEtransfers and supports Enhanced PIO Modes 3 and 4and BusMaster IDE DMA

Mode2 devices

Onboard20-pinATX PowerSupply

ATXpower supports soft-on/offfunction

SystemBIOS

LicensedBIOSwithadditionalfeature:

*FlashEEPROM(128KB) for BIOSupdate

*ISAPlug & Playextension

*Powermanagement

*SupportDMI (Desktop Management Interface) function

ACPI:

SupportACPI(AdvancedConfigurationandPowerInterface) function. ACPI provide

moreEnergy SavingFeatures for the future operating system supporting OS Direct

PowerManagement (OSPM) functionality.

BoardSize:

ATXform factorsize 305mmx 210mm.

ACCESSORIESOF HOT-595

Figure 1 : Accessories of HOT-595

HardwareConfiguration

Thischapter is designed for explaininghow to configure the HOT-595'shardware. After youinstall the

mainboard, youcan setjumpers, installmemory onthe mainboard, andmake caseconnectors. Refer to

thischapter whenever youupgrades or reconfigureyour system.

Jumper Setting

Thissection describe the necessary proce-

duresand proper jumpersettings to configure

theHOT-595 mainboard.

Jumperpin headers and DIP Switch show on

rightside are used to configuresystem clock,

CPUmultiplier and CPU voltages.

SystemClock -

Switch1~Switch3of DIP Switch SW2

DIPSwitch SW2 finger 1~3 is used to adjust

SystemClock from 50MHz to 83 MHz.

CPU Multiplier -

Switch4~Switch6of DIP Switch SW2

DIPSwitch SW2 finger 4~6 is used to adjust

CPUcore multiplierfrom 1.5Xto 5.5X.

AutoDetect CPU Voltages Auto/ Figure 2-1 : SW1 & SW2 location

Insertajumperpack on SW1

RowB-CtosetCPUvoltage

auto-detecting

Removejumperpack fromSW1

and insertminion pin1,3,4or

RowA-Btosetvoltage on 3.3V

Switch5issettoON.

Switch1,2,3,4,6aresettoOFF

Switch1,4,5aresettoON

Switch2,3,6aresetup OFF

ManualJumper-SW1

HOT-595automaticallydetectsandadjuststhevoltage to the proper voltage.

Jumperblock SW1 isused to setAutomaticallyor Manually adjustonboard voltages output

fromSwitching type regulators to CPU by inserting or removing mini jumperfrom pin

headers.(please also referto page 13)

Thosehardware settings aremade throughthe use ofDIP Switch and jumper capsto connect

jumperpins on the main board.

Thefollowing examplesshow theconventions usedin thischapter.

CPUClock Configuration -DIP Switch SW2

DIPSwitch SW2 and Jumper Block SW1 are the onlySwitch/Jumper that you need to set for your CPU

onHOT-595. Make sure that you know the type of CPU that you are installingand referto the proper

settingswhich are listedbelow. Normally, CPU voltageis auto-detected onHOT-595 and isset to Auto-

detectedwhen HOT-595 is delivered. If you have a higher frequencyCPU or you want to set CPU

frequencyand voltagemanually, pleaserefer tonext twosections.

Intel Pentium (P54C) Series CPUs Settings

ProcessorSpeedFrequency Settings

DIPSwitchSW2

JumperBlock

SW1

Vcore/Vio

Auto-detect

IntelPentium

(P54C)

200 MHzExternal:66MHz

Multiplier:3x

3.3V/3.3V

166 MHzExternal:66MHz

Multiplier:2.5x

150 MHzExternal:60MHz

Multiplier:2.5x

133 MHzExternal:66MHz

Multiplier:2x

120 MHzExternal:60MHz

Multiplier:2x

100 MHzExternal:66MHz

Multiplier:1.5x

90 MHzExternal:60MHz

Multiplier:1.5x

75 MHzExternal:50MHz

Multiplier:1.5x

Table 2-1

Intel Pentium MMX (P55C) Series CPUs Settings

ProcessorSpeedFrequency Settings

DIPSwitchSW2

JumperBlock

SW1

Vcore/Vio

Auto-detect

Intel Pentium

P55CMMX

233 MHzExternal:66MHz

Multiplier:3.5x

2.8 V/3.3V

200 MHzExternal:66MHz

Multiplier:3x

166 MHzExternal:66MHz

Multiplier:2.5x

AMD-K6 Series CPUs Settings

ProcessorSpeedFrequency Settings

DIPSwitchSW2

JumperBlock

SW1

Vcore/Vio

Auto-detect

AMD-K6

266 MHzExternal:66MHz

Multiplier:4x

2.2V/3.3V

233 MHzExternal:66MHz

Multiplier:3.5x

233 MHzExternal:66MHz

Multiplier:3.5x3.2V/3.3V

200 MHzExternal:66MHz

Multiplier:3x

2.9V/3.3V

166 MHzExternal:66MHz

Multiplier:2.5x

Note :The voltage of AMD-K6 233MHz may vary from market and CPU core. Please ask your

CPU provider for detail.

Table 2-3

Table 2-2

Tabla de contenidos

Otros manuales de Placa madre de Shuttle

Shuttle

Shuttle Spacewalker AV30 Manual de usuario

Shuttle

Shuttle MB48 Manual de usuario

Shuttle

Shuttle MV43 Manual de usuario

Shuttle

Shuttle FB77 Manual de usuario

Shuttle

Shuttle MV21 Manual de usuario

Shuttle

Shuttle FX83 Manual de usuario

Shuttle

Shuttle Spacewalker AK32 Manual de usuario

Shuttle

Shuttle HOT-683 Manual de usuario

Shuttle

Shuttle AV11 Manual de usuario

Shuttle

Shuttle FN41V3 Manual de usuario

Shuttle

Shuttle AV42 Manual de usuario

Shuttle

Shuttle MN31 Manual de usuario

Shuttle

Shuttle AK32V Manual de usuario

Shuttle

Shuttle HOT-661/P Manual de usuario

Shuttle

Shuttle FN41U Manual de usuario

Shuttle

Shuttle HOT-433 Manual de usuario

Shuttle

Shuttle AT30 Manual de usuario

Shuttle

Shuttle MS11 Manual de usuario

Shuttle

Shuttle FB83 Manual de usuario

Shuttle

Shuttle Spacewalker AV45GT Manual de usuario

Shuttle

Shuttle Spacewalker HOT-687 Manual de usuario

Shuttle

Shuttle Spacewalker MV18 Manual de usuario

Shuttle

Shuttle AB52 Manual de usuario

Shuttle

Shuttle AE23 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario