Shuttle MVP Manual de usuario
Page 1
Tower Installation
If you discover damaged or missing parts, please contact Shuttle Systems
Page 2
Important Note:
PDF versions of these instructions are available at:
http://shuttlesystems.com/pages/faq
!!
Assembly of the Shuttle MVP Towers requires two people.
Keep in mind that the following images pertain to just one of the three
available Shuttle MVP models, your parts may appear slightly different than
those in the included images but, the required steps remain the"
same.
If there is any shipping damage please take a photo of the damage and "
Tools Needed:
1/2 inch socket or combination wrench "
Allen wrench (provided in Parts Bag)
Socket Wrench Set
Typical combination wrench set
Page 3
MVP TOWER INSTALLATION
The Towers will come in one box
!1. Towers
- Towers"
!!- Wings"
!!- Parts Bag (Rope, Allen wrench, Pulley Systems)"
"
Head-End Stand"
(Head-End)
It is important to become familiar with the “Head-End” of the machine as it
refers to the end of the stand the Towers will be installed
Page 4
STEP 1
INSTALLING TOWER BASE
ITEMS
REQUIRED"
TOWER BASE"
1/2” SOCKET#
#
PARTS BAG
1. Remove the Kickplate Board. This can be done by unscrewing the 4 knurled knobs from
the back of the Kickplate Structure. (Pic 1.1)"
2. Remove the Carriage. This can be done by unscrewing the 4 Eyebolts and removing the 2
Knee Bumpers at the Head-End of the Rails. (Pic 1.2)"
3. Once the Kickplate Board and Carriage are removed, turn the Shuttle MVP on its side to
get access to the two feet at the Head-End Stand. This step is easier with two people.
4. Remove the two feet on the Head-End stand using a 1/2” socket and the included Allen
wrench in the Parts Bag. (Pic 1.4)"
5. Position and secure the Tower Base to the exposed bolt holes and tighten the two feet
back down. Once done flip the Machine upright and secure the Kickplate Board and
Carriage. (Pic 1.5)
Pictures are on the next page.
Page 5
1.1
1.2
1.4
1.5
Knee Bumpers"
Eye Bolts
Page 6
STEP 2
ATTACHING THE WINGS
ITEMS"
REQUIRED"
TOWER
WINGS"
PARTS BAG
1. Remove the top two bolts from the Head-End Stand and add the wings in alignment with
the now exposed bolt holes. (Pic 2.1)"
2. Using the hardware attached to the Wings, tighten down fully to the MVP Rails with the lock
nuts facing outwards. (Pic 2.2)"
3. Place the nut caps now exposed on the outside of the machine."
2.1"
2.2"
2.3
Page 7
STEP 3
ATTACHING THE TOWERS
ITEMS "
REQUIRED"
TOWERS"
PARTS BAG
1. Unwrap and remove the hardware from the Towers along with loosening the bottom bolt."
2. Position and attach the Towers onto the Plastic Blocks at the Head-End Stand. The Towers
should go out from the machine. (Pic 3.2)"
3. Insert the bolts that were originally attached to the Towers, through the Wings and out
through the Towers. Tighten once in position. (Pic 3.3)"
4. Secure the base of the Towers by tightening down the bottom bolts to the Plastic Blocks.
(Pic 3.4)
3.2
3.3
3.4
Page 8
STEP 4
INSTALLING THE PNF PULLEYS & ROPE
ITEMS "
REQUIRED"
ROPE CLEAT"
PNF PULLEYS"
ROPE
1. Attach the PNF Pulleys to the eyebolt at the desired height of both Towers. (Pic 4.1)"
2. Feed the rope through both Pulleys leaving the handles resting on the ground. (Pic 4.2)"
3. Located on the side of the carriage are two plastic hole inserts. Remove all 4 of the plastic
inserts from the carriage (2 on each side) and insert the Rope Cleat. Tighten down fully."
4. Secure the rope by pushing the rope into the Rope Cleat. The rope should not move
through the Cleat. (Pic 4.4).
4.1
4.4
4.2
Page 9
Finally, you have one of the greatest machines on earth....
Well, at least we'd like to think so - and many of our owners agree.
Therefore, enjoy it!
Leave us a review on our website!
Please visit us at:
www.ShuttleSystems.com
1-800-334-5633
Made in the
USA
Otros manuales para MVP
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Equipo de fitness de Shuttle
Shuttle
Shuttle MVP Elite Plus Manual de usuario
Shuttle
Shuttle BALANCE Manual de usuario
Shuttle
Shuttle MVP Manual de usuario
Shuttle
Shuttle Ultimate Manual de usuario
Shuttle
Shuttle BALANCE Manual de usuario
Shuttle
Shuttle Shuttle Recovery Manual de usuario
Shuttle
Shuttle BALANCE Manual de usuario
Shuttle
Shuttle TNT Manual de usuario
Shuttle
Shuttle MiniPress Manual de usuario
Shuttle
Shuttle TNT Manual de usuario
