Shure R180 Manual de usuario
1/4
R180 -- Replacement Cartridge
General Description
Shure Model R180 Replacement Cartridge For
Models 588SDX, 515SDX, 515SBGX, 515SBG-18X,
515SBG-18XF, and 515BSLX
This kit contains the following:
•One R180 replacement cartridge
•Two pieces of shrink-wrap tubing (for 515SBGX, 515SBG-8X, 515SBG-8XF, and 515BSLX only)
The following tools are needed to replace the cartridge:
•Long-nose pliers (for 588SDX and 515SDX only)
•A soldering iron of 25 to 40 watts
•Wire cutters (for 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)
•#4 (.050 in., 1.3 mm) hex wrench (supplied with 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)
Shure Incorporated
2/4
Models 588SDX and 515SDX
Wiring Diagram
It is recommended that the following procedure be performed on a table or other flat surface to support the car
tridge and case in order to avoid the possibility of breaking the cartridge leads.
To replace the R180 cartridge in the 588SDX and 515SDX, proceed as follows:
1. Unscrew and remove the grille (turning counterclockwise).
2. Gently pull out the old cartridge, being careful not to break the leads.
3. Using a Phillips screwdriver, remove the screws and lock plate which hold the switch in place.
4. Using long-nose pliers, gently pull out the switch, being careful not to break the leads.
5. Unsolder and remove the leads of the old cartridge from the switch.
To prevent damage to the switch, soldering iron between 25 and 40 watts is recommended.
6. Solder the lead closest to the RED dot on the new cartridge (see wiring diagram above) to the terminal with the
YELLOW lead on the switch.
Shure Incorporated
3/4
7. Solder the other lead from the new cartridge to the terminal with the BLUE lead on the switch.
8. Using longnose pliers, carefully replace the switch in the case with the blank terminal on the switch facing to
wards the cartridge (to ensure the UP position is ON), being careful not to pinch the leads.
9. Placing your finger inside the case to support the switch, secure the switch in place by screwing the nonlock
plate screw on the side of the switch closest to the grille.
10. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam
gasket on the cartridge is above the aluminum ring.
11. Replace and screw on the grille.
12. Replace the lockplate on the side of the switch opposite the grille, then secure it with the remaining screw.
Models 515BSLX, 515SBGX, 515SBG-18X, and 515SBG-18XF
It is recommended that the following procedure be performed on a table or other flat surface to support the car
tridge and case in order to avoid the possibility of breaking the cartridge leads.
To replace the R180 cartridge in the 515X Series (except the 515SDX), proceed as follows:
1. Slide the supplied shrink-wrap tubing over both leads on the R180 replacement cartridge.
2. Using a #4 (.050 in., 1.3 mm) hex wrench, loosen the setscrew on the base of the grille.
3. Unscrew and remove the grille (turning counterclockwise).
4. Gently pull out the old cartridge, being careful not to break the leads.
5. Using wire cutters, cut the lead from the old cartridge marked by the dot as close to the cartridge as possible,
so the lead sticks out from the handle. Mark the cut lead with a small piece of tape.
Shure Incorporated
4/4
6. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.
7. Take the lead marked with a red dot on the R180 replacement cartridge and splice it to the taped lead, twisting
the stripped ends together.
8. Solder the spliced leads.
To prevent damage to the leads, a soldering iron of 25 to 40 watts is recommended.
9. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of
the soldering iron back and forth along the shrink-wrap tubing until it shrinks.
10. Using wire cutters, cut the other lead of the old cartridge as close to the cartridge as possible, so the lead sticks
out from the handle.
11. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.
12. Take the unmarked lead on the R180 replacement cartridge and splice it to the second lead of the handle,
twisting the stripped ends together. Solder the leads.
13. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of
the soldering iron back and forth along the shrink-wrap tubing until it shrinks.
14. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam
gasket on the cartridge is above the aluminum ring.
15. Replace and screw on the grille.
16. Using a #4 (.050 in., 1.3 mm) hex wrench, secure the grille by tightening the setscrew.
Do not torque the setscrew too tightly.
Tabla de contenidos
Otros manuales de Equipo de grabación de Shure
Shure
Shure PS9 Manual de usuario
Shure
Shure MV88+ Manual de usuario
Shure
Shure M97xE Manual de usuario
Shure
Shure DFR11EQ Version 5 Manual de lista de piezas
Shure
Shure DT15P Manual de usuario
Shure
Shure PSM 600 Manual de usuario
Shure
Shure ANI4OUT Manual de usuario
Shure
Shure AMS880 Manual de usuario
Shure
Shure PSM 300 Manual de usuario
Shure
Shure MVI Manual de usuario
Shure
Shure PSM1000 Manual técnico
Shure
Shure ANIUSB-Matrix Manual de usuario
Shure
Shure DFR11EQ Version 5 Manual de usuario
Shure
Shure P3RA Manual de usuario
Shure
Shure 44 Series Manual de usuario
Shure
Shure PSM 200 Guía de inicio rápido
Shure
Shure M78S Manual de usuario
Shure
Shure PSM 900 Manual de usuario
Shure
Shure ANI4IN Series Manual de usuario
Shure
Shure Access Manual de usuario
Manuales populares de Equipo de grabación de otras marcas
Strymon
Strymon NIGHTSKY Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario
Tews Technologies
Tews Technologies TPMC465 Manual de usuario
Honeywell
Honeywell Excel 50 Manual de usuario
SeaLevel
SeaLevel COMM+8.LPCI Manual de usuario
Arturia
Arturia AUDIOFUSE STUDIO Manual de usuario
