Showline SL BEAM 100 Manual de usuario

SL BEAM 100

LED LUMINAIRE

Note: Information contained in this document may not be duplicated in full or in part by any person without prior

written approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment

mentioned. The use of this document for all other purposes is specifically prohibited.

Document Number: SL BEAM 100 LED Luminaires Users

Version as of: 11th Sep, 2014

SL BEAM 100 LED Luminaire Installation & User’s Manual

SL BEAM 100 LED Luminaires Installation & User’s Manual

Sh wline

IMPORTANT INFORMATION

Warnings and Notices

Additional Resources for DMX512

For more information on installing DMX512 control systems, the following publication is available for purchase

from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide

for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:

USITT

315 South Crouse Avenue, Suite 200

Syracuse, NY 13210-1844

Phone: 1.800.938.7488 or 1.315.463.6463

www.usitt.org

Showline Limited Two-Year Warranty

Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the

date of delivery. A copy of Showline two-year limited warranty containing specific terms and conditions can be

obtained by contacting your local Showline office.

When using electrical equipment, basic safety precautions should always be followed including the following:

a.READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

b.Do not use outdoors.

c.Do not mount near gas or electric heaters.

d.Equipment should be mounted in locations and at heights where it will not readily be subjected to

tampering by unauthorized personnel.

e.The use of accessory equipment not recommend ed by the manufacturer may cause an unsafe

condition.

f.Do not use this equipment for other than intended use.

g.Refer service to qualified personnel.

SAVE THESE INSTRUCTIONS.

WARNING : You must have access to a main circuit breaker or other power disconnect device

before installing any wiring. Be sure that power is disconnected by removing fuses or turning the

main circuit breaker off before installation. Installing the device with power on may expose you to

dangerous voltages and damage the device. A qualified electrician must perform this installation.

WARNING : Refer to National Electrical Codes and local codes for cable specifications. Failure to

use proper cable can result in damage to equipment or danger to personnel.

WARNING : This equipment is intended for installation in accordance with the National Electric

Code®and local regulations. It is also intended for installation in indoor applications only. Before

any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid

shock or damage to the control. It is recommended that a qualified electrician perform this

installation.

Installation & User’s Manual SL BEAM 100 LED Luminaires

2TABLE OF CONTENTS Sh wline

TABLE OF CONTENTS

IMPORTANT INFORMATION

TABLE OF CONTENTS

PREFACE

SL BEAM 100 LED LUMINAIRE OVERVIEW

INSTALLATION AND SET UP

OPERATION AND PROGRAMMING

DMX CONTROL

CLEANING AND CARE

TECHNICAL SPECIFICATIONS

SL BEAM 100 LED Luminaire Dimensions 37

......................................................................................................

Showline Offices ................................................................................................................................... 0

Warnings and Notices ............................................................................................................................. 1

Additional Resources for DMX512 ........................................................................................................... 1

Showline Limited Two-Year Warranty....................................................................................................... 1

About this Manual ........................................................................................................................................ 3

Included Items ..............................................................................................................................................3

Accessories ................................................................................................................................................. 3

SL BEAM 100 LED Luminaire Power Input Cables

.................................................................................... 3

SL BEAM 100 LED Luminaire Accessories ............................................................................................... 3

SL BEAM 100 LED Luminaire Components .................................................................................................... 4

Major Luminaire Components .................................................................................................................. 4

LCD Display / Menu System................................................................................................................... 5

Power Requirements...................................................................................................................................... 6

AC Power Operation............................................................................................................................... 6

Connecting Power ......................................................................................................................................... 6

Connecting SL BEAM 100 LED Luminaires to AC Power ............................................................................ 6

Connecting to the DMX512 Network................................................................................................................ 7

Mounting Luminaire...................................................................................................................................... 8

LCD Display and Menu System ..................................................................................................................... 9

LCD Display and Menu System Operation ....................................................................................................... 9

Menu Tree .................................................................................................................................................. 10

Quick Selection Buttons ................................................................................................................................ 11

Edit a Preset Button ............................................................................................................................... 11

Edit a Chase Button

............................................................................................................................... 11

DMX Address Button ............................................................................................................................. 11

Dimming Curve Selection.............................................................................................................................. 12

Master / Slave Operational Mode ................................................................................................................... 13

Simple 8-bit Mode ........................................................................................................................................ 14

Simple 8-bit Group Mode ............................................................................................................................... 15

RGBW 8-bit Mode ........................................................................................................................................15

RGBW 8-bit Group Mode ...............................................................................................................................19

RGBW 16-bit Mode ...................................................................................................................................... 19

HSIC Mode ..................................................................................................................................................24

RGBW 16-bit GroupMode .............................................................................................................................. 23

HSIC GroupMode ......................................................................................................................................... 25

SL BEAM 100 LED Luminaire DMX Timing Channel Details.............................................................................. 26

SL BEAM 100 LED Luminaire RDM Parameter IDs .......................................................................................... 32

Special Cleaning and Care Instructions ............................................................................................................. 36

Front Lens Cleaning ..................................................................................................................................... 36

Service and Maintenance

............................................................................................................................... 36

SL BEAM 100 LED Luminaire Operational Specifications .................................................................................. 37

About this Manual 3

Sh wline

PREFACE

1.About this Manual

The document provides installation and operation instructions for the following products:

S L BEAM 100 LED Luminaire

Please read all instructions before installing or using this product. Retain this manual for future reference. Additional

product information and descriptions may be found on the product specification sheet.

Note: The SL BEAM 100 LED Luminaire is universal voltage 100 to 240 VAC (auto-ranging).

2.Included Items

Each SL BEAM 100 LED Luminaire includes the following items:

S L BEAM 100 LED Luminaire

SL BEAM 100 Quick Start Guide

3.Accessories

SL BEAM 100 LED Luminaire Power Input Cables

SL BEAM 100 LED Luminaire Accessories

Part Number

17-003-0054-00 SL BEAM 100 LED Luminaire AC Power Input Cable ( 1.5 meter)

Part Number Description

Description

60-600-0134-00 Omega Lock for SL BEAM 100 LED Luminaire

SL BEAM 100 LED Luminaires Installation & User’s Manual

4SL BEAM 100 LED LUMINAIRE OVERVIEW

SL BEAM 100 LED LUMINAIRE OVERVIEW

1. SL BEAM 100 LED L u minaire Components

Major Luminaire Components

Figure 1: SL BEAM 100 LED Luminaire Components

Note: *Mounts can be removed and reversed. See "Mounting Luminaire" on page 8 for more information.

Top of Unit

High-Intensity RGBW LED Array

Luminaire Head

DMX512/

AC Input

LCD Display / Menu System

RDM Input

DMX512/

AC Output

RDM Output

Arm

Installation & User’s Manual SL BEAM 100 LED Luminaires

Sh wline

LCD Display / Menu System

Figure 2: LCD Display & Menu System

Note: For Menu operation and programming details, refer to "LCD Display and Menu System" on page 9.

SL BEAM 100

Home (menu settings)

Edit a Preset Edit a Chase

DMX512 Addressing

Return to Main Screen

LEFT Arrow Button UP Arrow Button

CHECK MARK (Accept) Button

DOWN Arrow Button

RIGHT Arrow Button

LCD Display

NOTE: Menu rotates with orientation of luminaire and

menu buttons are always in the same position (with

rotation of menu)

To rotate menu 180 degrees from current orientation,

press and hold the two center buttons for 2 seconds.

SL BEAM 100 LED Luminaires Installation & User’s Manual

Sh wline

6INSTALLATION AND SET UP

INSTALLATION AND SET UP

1.Power Requirements

The SL BEAM 100 LED Luminaire operates on AC input voltages from 100 to 240 VAC.

WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely

remove power from unit when not in use.

AC Power Operation

When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire

contains an auto-ranging power supply. Each luminaire can draw up to 150 Watts.

WARNING! Maximum amount of units that may be daisy-chained is (A) 11 units 100 ~ 120VAC (15 Amps) or (B)20

units 230 ~ 240VAC (15 Amps).

Note: For wiring of AC input connector, refer to "Connecting SL BEAM 100 LED Luminaires to AC Power"

on page 6.

2.Connecting Power

Units can be powered in one of two ways:

Direct connection to a AC power sour c e using an AC input cable.

Connection from the AC output of another SL BEAM 100 L ED Luminaire. When using this method, it is

very important not to connect any other type of equipment device.

WARNING! Only connect other SL BEAM 100 LED Luminaires to the AC Output (Thru) connector of a SL

BEAM 100 L ED Luminaire.

Connecting SL BEAM 100 LED Luminaires to AC Power

Figure 3 on page 7 describes how to connect power to your SL B EAM 100 LED Luminaire. Field wiring of the

SL BEAM 100 LED Luminaire is straight forward. A total of 3 wires/conductors is supplied from the unit. The

following wiring scheme is used:

Table 1: SL BEAM 100 LED Luminaire Voltage (VAC) vs. Current*

Voltage (AC)Total Current (A)Voltage (AC)Total Current (A)

Installation & User’s Manual SL BEAM 100 LED Luminaires

Sh wline

Connecting to the DMX512 Network 7

Figure 3: SL BEAM 100 LED Luminaire AC Input & Output Connections

CAUTION: In the event the AC input cable of this luminaire is damaged, it must be replaced, by the user, with an

approved cable through an Authorized Showline Dealer or Service Center.

3.Connecting to the DMX512 Network

Basic DMX512 installation consists of connecting multiple SL BEAM 100 LED Luminaires together (up to 32

luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX

connector on the first SL BEAM 100 LED Luminaire. Another cable runs from the other DMX connector on

the first unit to a DMX connector on the next SL BEAM 100 LED Luminaire (or DMX512 device to

be controlled).

Figure 4: SL BEAM 100 LED Luminaire DMX512 Input / Output Connections

AC Input

AC Output

Neutral Main /

Ground / Earth

Line

AC Connector

(on side of unit)

AC Input Connector (on Unit)

Neutral

Main /

Ground / Earth

Line

AC Connector

(on side of unit)

AC Output Connector (on Unit)

DMX512 / RDM Input

DMX512 / RDM Output

SL BEAM 100 LED Luminaires Installation & User’s Manual

Sh wline

Mounting Luminaire

Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on

page 1. For SL BEAM 100 LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 14.

Figure 5: SL BEAM 100 LED Luminaire - DMX512 Connections

4. Mounting Luminaire

The SL BEAM 100 LED Luminaire is provided with two mounts and safety cable anchor points.

The two mounts are easily removed and reversed as required. These mounts are designed to accept a variety of

mounting hooks, clamps, etc. for hanging applications. Refer to Figure 6 for additional information. Note, the bottom

Simply attach hook, clamp, etc. to the SL BEAM 100 LED Luminaire mount assembly in the M13 hole.

Note: Mounting hooks, clamps, etc. are sold separately or by others. For available mounting accessories refer to

"Accessories" on page 3.

Figure 6: Mounting Luminaire - Hanging Applications

DMX512

DMX512 (out from first

to second luminaire)

DMX512 (out to the next

luminaire or DMX512

controlled device)

SL BEAM 100 SL BEAM 100

DMX512 Connections

Note: Remaining pins on each connector are not used.

DMX512 Signal XLR Pin

Common (Drain)1

DMX512 - 2

DMX512 + 3

(from console or

control device)

LED Luminaires LED Luminaires

of the luminaire must be free and clear of any objects (i.e.,scenery) to allow for proper airflow

SAFETY CABLE: Is sold

separately and recommended

for all hanging installation and

may be required by national

Hook / Clamp

and local codes. Use enclosure

handles for safety cable anchor

points for this fixture.

Installation & User’s Manual SL BEAM 100 LED Luminaires

Sh wline

Tabla de contenidos

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario