Show Tec LAMPY Re-Load 4 Manual de usuario

LAMPY Re-Load 4

Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands

Product code: 50744

USER MANUAL

ENGLISH

LAMPY Re-Load 4

Product code: 50744

Preface

Thank you for purchasing this Showtec product.

The purpose of this user manual is to provide instructions for the correct and safe use of this product.

Keep the user manual for future reference as it is an integral part of the product. The user manual shall be

stored at an easily accessible location.

This user manual contains information concerning:

●Safety instructions

●Installation and operation of the device

●Intended and non-intended use of the device

●Maintenance procedures

●Troubleshooting

●Transport, storage and disposal of the device

Non-observance of the instructions in this user manual may result in serious injuries and damage of

property.

No part of this document may be copied, published or otherwise reproduced without the prior written

consent of Highlite International.

Design and product specifications are subject to change without prior notice.

For the latest version of this document or other language versions, please visit our website

www.highlite.com or contact us at service@highlite.com.

Highlite International and its authorized service providers are not liable for any injury, damage, direct or

indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or

reliance on the information contained in this document.

LAMPY Re-Load 4

Product code: 50744

Table of contents

1. Introduction..........................................................................................................................................................3

Before Using the Product ..................................................................................................................................3

Intended Use .......................................................................................................................................................3

Product Lifespan.................................................................................................................................................3

Text Conventions ................................................................................................................................................3

Symbols and Signal Words................................................................................................................................4

Symbols on the Information Label ..................................................................................................................4

2. Safety ....................................................................................................................................................................5

Warnings and Safety Instructions ....................................................................................................................5

Requirements for the User.................................................................................................................................6

3. Description of the Device ...................................................................................................................................7

Front View ............................................................................................................................................................7

Product Specifications ......................................................................................................................................8

Compatibility.......................................................................................................................................................8

Dimensions...........................................................................................................................................................9

4. Installation ..........................................................................................................................................................10

Safety Instructions for Installation ..................................................................................................................10

Installation Site Requirements ........................................................................................................................10

Installation..........................................................................................................................................................10

Rack Mounting........................................................................................................................................10

Recessed Mounting ...............................................................................................................................11

5. Setup and Operation ........................................................................................................................................12

Warnings and Precautions .............................................................................................................................12

Setup Example ..................................................................................................................................................12

Connecting to the LAMPY Console..............................................................................................................13

Connecting Stage Effects to the Device ....................................................................................................14

DMX-512 Protocol...................................................................................................................................14

DMX Cables.............................................................................................................................................14

Connecting to Power Supply.........................................................................................................................14

6. Troubleshooting .................................................................................................................................................15

7. Maintenance .....................................................................................................................................................15

Preventive Maintenance................................................................................................................................15

Basic Cleaning Instructions ...................................................................................................................15

Corrective Maintenance................................................................................................................................16

8. Deinstallation, Transportation and Storage ....................................................................................................16

9. Disposal ..............................................................................................................................................................16

10. Approval.............................................................................................................................................................16

LAMPY Re-Load 4

Product code: 50744

1. Introduction

Before Using the Product

Important

Read and follow the instructions in this user manual before installing, operating or

servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of

this manual.

After unpacking, check the contents of the box. If any parts are missing or damaged, contact your

Highlite International dealer.

Your shipment includes:

●Showtec LAMPY Re-Load 4

●AC power adapter (1,1 m)

●User manual

Mounting kit:

●Long mounting bracket

●2 x short mounting bracket

●12 x mounting screw for a 19-inch rack

Fig. 01

Intended Use

This device is intended for use as a DMX extension kit. This device is not suitable for households.

Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

Product Lifespan

This device is not designed for permanent operation. Disconnect the device from the electrical power

supply when the device is not in operation. This will reduce the wear and will improve the device’s

lifespan.

Text Conventions

Throughout the user manual the following text conventions are used:

●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”

●References: References to chapters and parts of the device are in bold lettering, for example:

“Refer to 2. Safety”, “press the power switch (03)”

●0–255: Defines a range of values

●Notes: Note: (in bold lettering) is followed by useful information or tips

LAMPY Re-Load 4

Product code: 50744

Symbols and Signal Words

Safety notes and warnings are indicated throughout the user manual by safety signs.

Always follow the instructions provided in this user manual.

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in

death or serious injury.

WARNING

Indicates an imminently hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

Attention

Indicates important information for the correct operation and use of the

product.

Important

Read and observe the instructions in this document.

Provides important information about the disposal of this product.

Symbols on the Information Label

This product is provided with an information label. The information label is located on the bottom plate of

the device.

The information label contains the following symbols:

This device shall not be treated as household waste.

Read and follow the instructions in the user manual before installing, operating or

servicing the device.

This device is designed for indoor use.

This device falls under IEC protection class III.

LAMPY Re-Load 4

Product code: 50744

2. Safety

Important

Read and follow the instructions in this user manual before installing, operating or

servicing this product.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of

this manual.

Warnings and Safety Instructions

DANGER

Danger for children

For adult use only. The device must be installed beyond the reach of children.

●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within

children’s reach. Packaging material is a potential source of danger for children.

Attention

Incorrect handling of the AC power adapter may result in hazardous situations

This device is delivered with an AC power adapter. Incorrect handling of the AC power adapter may

result in hazardous situations.

●Use only the AC power adapter delivered with the device.

●Do not wrap the power cable around the power adapter or any other object. This can damage the

internal wires.

●Do not cover the power adapter with anything when it is plugged into the socket-outlet. This may

cause overheating.

●Do not expose the power adapter to water or other liquids.

Do not use the power adapter:

●If it shows signs of overheating, for example the plastic is damaged

●If the AC input pins show signs of corrosion or overheating

●If the power cable is damaged or shows signs of material fatigue.

Attention

Power supply

Before connecting the AC power adapter to the power supply, make sure that the current, voltage and

frequency match the input voltage, current and frequency specified on the information label on the AC

power adapter.

LAMPY Re-Load 4

Product code: 50744

Attention

General safety

●Do not shake the device. Avoid brute force when installing or operating the device.

●If the device is dropped or struck, disconnect the device from the electrical power supply

immediately.

●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it

on immediately. Let the device reach room temperature before switching it on, otherwise it may be

damaged by the formed condensation.

●If the device fails to work correctly, discontinue the use immediately.

Attention

This device shall be used only for the purposes it is designed for.

This device is designed to be used as a DMX extension kit. This device is not suitable for households.

Any incorrect use may lead to hazardous situations and result in injuries and material damage.

●This device is not suitable for households.

●This device does not contain user-serviceable parts. Unauthorized modifications to the device will

render the warranty void. Such modifications may result in injuries and material damage.

Attention

Do not expose the device to conditions that exceed the rated IP class conditions.

This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater

than 12 mm, such as fingers, and no protection against harmful ingress of water.

Requirements for the User

This product may be used by ordinary persons. Maintenance and installation may be carried by ordinary

persons. Service shall be carried out only by instructed or skilled persons. Contact your Highlite

International dealer for more information.

Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled

person, for specific tasks and work activities associated with the service of this product, so that they can

identify risks and take precautions to avoid them.

Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards

associated with the service of this product.

Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons

include not only users of the product but also any other persons that may have access to the device or

who may be in the vicinity of the device.

LAMPY Re-Load 4

Product code: 50744

3. Description of the Device

The LAMPY Re-Load 4 is a plug-and-play DMX extension kit that releases 4 additional universes on any

LAMPY console (in total 2048 additional channels). It has both 3-pin and 5-pin DMX output connectors for

each additional universe. The device can be mounted on a 19-inch rack. The power supply input is fitted

with a lockable DC plug.

Front View

Fig. 02

5 V DC power connector IN

USB B connector IN

4 x 3-pin/5-pin DMX connector OUT (outputs 3–6)

Kensington lock port

Link LED indicator

Online LED indicator

LAMPY Re-Load 4

Product code: 50744

Product Specifications

Model:

LAMPY Re-Load 4

Electrical:

Input voltage:

5 V DC

Power consumption:

5 W

AC power adapter:

Input voltage:

100–240 V AC, 50/60 Hz

Output voltage:

5 V DC

Physical:

Dimensions:

279 x 72 x 44,5 mm (L x W x H), 1U

Weight:

0,3 kg

Connections:

Power connection:

5 V DC power connector IN

Output connections:

4 x 3-pin DMX connector OUT

4 x 5-pin DMX connector OUT

Data connections:

USB B connector IN

Operation and control:

Control mode:

DMX

DMX channels:

2048

Universes:

Construction:

Housing:

Metal

Color:

Black

IP rating:

IP20

Thermal:

Maximum ambient temperature ta:

40 °C

Minimum ambient temperature ta:

0 °C

Minimum ambient temperature:

-5 °C

Compatibility

The device does not function when it is not connected to a LAMPY console.

The device is compatible with the following LAMPY consoles:

●50740 (LAMPY 20 1U, 1 universe and 20 faders)

●50741 (LAMPY 20 2U, 2 universes and 20 faders)

●50742 (LAMPY 40 1U, 1 universe and 40 faders)

●50743 (LAMPY 40 2U, 2 universes and 40 faders)

LAMPY Re-Load 4

Product code: 50744

Dimensions

Fig. 03

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Extensor de Show Tec

Show Tec

Show Tec Booster 2 Manual de usuario

Show Tec

Show Tec DB-1-4 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario