Shelly ShellyEye Manual de usuario
USER GUIDE
WARRANTY & WARRANTY TERMS
Allterco Robotics EOOD
Sofia, Bulgaria © 2018
3G & WiFi Smart Camera
1
USER GUIDE
Shelly®Eye Smart Camera
LEGEND:
Front
1. Power/Reset Button
2. LED
3. Camera Lens
4. IR
5. Microphone
6. Motion sensor
Rear
7. SD (Memory) Card Slot
8. SIM Slot
9. Speaker
10. Power Port - Micro USB
The smart camera with 3G & WiFi, Shelly Eye by Allterco Robotics streams live video, saves
videos on Cloud or SD. Shelly Eye can send motion and audio detected alerts, hear and
respond with two-way audio and the integrated battery provides up to a 24h of recording
without power supply. Shelly may work as a standalone Device or as an accessory to She® or
other home automation controller.
fig.1 fig.2
2
Specification
Camera Sensor: 1MP CMOS
Resolution:
• HD – 1280x720 p
• WVGA – 640x352 p
Camera Lens:
• Aperture - F2.2
• Angle - 110° wide
Video:
• Compression format – H.264
• FPS – max 30
Audio Format: G.711 (16 bit/8 KHz)
3G: WCDMA (band 1, 2, 5, 8)
WiFi:
• Protocol: 802.11 b/g/n
• Frequency: 2.4 GHz
WiFi Operational range (depending on
local construction):
• up to 30 m outdoors
• up to 10 m indoors
Motion detection
• Angle - 120°
• Range – up to 5 m
Power supply: 5V/2A DC
Power consumption: < 5W
Battery: Li-Ion 1000mAh
Battery life: Up to 24 hours
Memory: SD Card (up to 32GB)*
Working temperature: -20 ÷ 50°C
Dimensions (HxD):
Device - 122 x 41 x 40 mm
Stand - 34 x 41 x 39 mm
Device & Stand - 150 x 41 x 40 mm
*Memory card not included
Buttons and indicators
Button:
• Turn on – hold, when the device is off
• Turn off – hold, when the device is on
Indicator Status
Red LED on Power on
Purple LED on Power Off
Yellow LED on No SIM card
Blue and yellow LED ash in a loop No network
Yellow LED ash slowly 3G network connected
Blue LED ash slowly WiFi connected
Red LED ashes quickly twice Stream live video
Red LED ashed slowly (interval: 1s) Recording
Red LED ashes quickly Upgrading software
Red LED ashes slowly Low battery
All LED OFF Power off/Sleep
3
Technical information
CAUTION! Keep the remote control devices (mobile phones, tablets, PCs) away
from children.
CAUTION! Use the Device only with power grid which complies with all applicable
regulations. In case Shelly Eye is connected to the power grid and a short circuit
occurs, it may damage the Device.
MOBILE APPLICATION
FOR SHELLY EYE®
Allterco Robotics EOOD
Sofia, Bulgaria © 2018
4
The Shelly Eye Mobile Application
Shelly Eye app gives you the opportunity to control and adjust all Shelly® Eye Cameras from
anywhere in the world. All you need is an Internet connection and our mobile application,
installed on your smartphone or tablet.
Initial Set-Up
The first time you open the Shelly Eye mobile app, you have to create an account to manage
your Shelly Eye® cameras.
Registration
1.Download and install the Shelly Eye mobile application. To install the application scan the
QR code on the box, or please visit Google Play (Android) or App Store (iOS).
2.Open the app and create an account by clicking on the Register button (fig. 3)
3.Input e-mail and password
4.Validate your account
5.Open the app again and press on the Sign In button.
Forgotten Password
In case you forget or lose your password, just
enter the e-mail address you have used in your
registration. You will then receive instructions
on how to change your password.
WARNING! Be careful when you type
your e-mail address during the
registration, as it will be used in case you
forget your password.
g. 3
5
Device Inclusion
To add a new Shelly camera, connect it to the power grid.
Step 1
Choose “Add Device” - fig. 4.
In order to add more Devices later, use the app menu at the top right corner of the main screen
and click “Add Device”.
Step 2
You will see the following screen - fig. 5
Scan the QR code placed on Shelly Eye. Upon successful scan of the code, the UUID of the
Device will be shown below the QR code frame. Press the tick sign at the top right of the
screen.
g. 4 g. 5
6
Step 3:
Select the Setup Mode (fig. 6):
• Mode 1 – If you have not inserted a SIM card, and you hear a voice prompt when the
Device boots up, press on Voice Prompt
• Mode 2 – If you have inserted a SIM card, press on No Voice Prompt
WARNING: In case the Device has not prompted with “Waiting for connection”, or
you want to add the Device to another Wi-Fi network, reset it. To reset the Device
press the button 10 consecutive times, then the LED will turn purple. After that the Device
will restart. If not, please repeat or contact our customer support at: support@shelly.cloud
g. 6 g. 7
7
MODE 1
Wi-Fi
Step 1:
When you hear the voice prompt you have to enter the Name (SSID) and password of your
WiFi network (fig. 7).
Step 2:
You will see a tip on how to proceed (fig.8)
Step 3:
You will hear a voice prompt to scan the QR code on your phone with Shelly Eye. Place the screen
of your phone in front of Shelly Eye and wait for the camera to scan the QR code (fig. 9).
g. 8 g. 9
8
Step 4:
Press Next when you hear the voice prompt that Shelly has scanned and connected
successfully.
Step 5:
Your Shelly Eye will connect to your WiFi and will be added to your account (fig. 10).
Step 6:
You will hear the voice prompt that Shelly has connected successfully. Press on “Start Using”
(fig. 11).
g. 11g. 10
9
g. 11
MODE 2
3G
Step 1:
Press on “No voice prompt” (fig. 6)
Step 2:
Your Shelly Eye will connect through mobile data and will be added to your account (fig. 10).
Step 3:
You will hear the voice prompt that Shelly has connected successfully. Press on “Start Using”
(fig. 11).
g. 10
Tabla de contenidos
