Automatic blocking of engine circuit (if this function is allowed in the programming mode). This function is designed to protect the
vehicle when it is forgotten to turn on the security system. The mode can be recognized from the constantly shining LED.The security system will not turn
on and will not lock the doors, but it will not be possible to start the engine. To start the engine (to turn off this state) press button 2: diode will fade – blocking
will be turned off and you will be able to start the engine. After pressing button 1 the system will go to protection mode immediately.
It is possible to choose two modes of automatic blocking:
1. Automatic blocking will turn on in 3 minutes after turning off the ignition. LED will shine constantly.
2. After turning off the ignition and opening the door the blocking will be activated immediately. If the door is not opened (you stay in the car) automatic
blocking will turn on in 10 min. LED will shine constantly. Note: this automatic blocking mode can be activated only if the ignition was turned on for 3
or more minutes.
Automatic turning on (if this function is allowable in programming mode). This function is designed for automatic turning on the system if you
turned off the system and forgot to turn it on again. The security system will turn on automatically if during 1 minute after its turning off the door is no
opened, no sensors are triggered or ignition is turned on. It is possible to choose whether the auto lock will lock the doors when this function initiates (see
Installation instruction).
The number of programmed remote controls. There are two remote controls in the set. The maximum number of remote
controls can be used (programmed) is 3. Every time the ignition is turned on, LED will blink as many times as many remote controls are programmed. If one
of the remote controls is lost, reprogram the rest near the main block. In this way the code of the lost remote will be deleted from the memory, and nobody
will be able to use lost remote.
Programming the remote controls. To program the additional (or to change the lost) remote control, perform the following procedure:
When the system is off turn on the ignition (immobilization mode must turned off).
Press and hold secret button (for about 5 sec.) until LED will shine constantly and then release it.
Press any button on the remote. After programming the first remote all codes of previously programmed remotes will be deleted from the memory and
LED will blink once. After pressing the button on the second remote LED will blink twice and on the third – three times.
You have about 12 sec. to program all remotes. After 12 sec. or after turning off the ignition the system will go out of remote programming mode
automatically.
Emergency turning off of the automatic blocking. If for some reasons the automatic blocking mode can not be turned off
using the remote control (LED shines constantly), perform the emergency turn off in exactly the same ways as described in the section: Emergency turning
off the security system.
Emergency turning off the security system. When the remote control is lost and the security system can not be turned off,
perform the emergency turn off. It would be performed in two ways: by pressing secret button or by entering PIN code, according 18 parameter in
parameters programming table (see Installation instruction).
✔
If PIN code is not used for emergency turning off, you have to open the door, turn on ignition and press a secret button.
✔
If PIN code is used for emergency turning off, you have enter three digits PIN code by the help of starting lock. Default producer PIN code is 212. (For
ex.: digit 2corresponds turning on ignition twice, digit 5 – turning on 5 times and etc.). For
emergency turning off with PIN code you must do:
1) turn on/off the ignition; the system will go to the emergency turning off mode. This will be
shown by the constantly shining of LED. Watch the state of LED. Short blinks of LED will
show which PIN digit must be entered: when LED fades for the first time, you must turn
on/off the ignition as many times as is the first digit of the PIN code.
2) after 20 second LED will blink twice – you have to enter second digit of PIN code, and after
20 seconds more LED will blink three times – enter the last digit of the PIN code.
3) if you did everything correctly, LED will fade in 10 sec. and the system will go out of
protection mode.
4) if you mixed one of the PIN code sets, wait until the program will go through all the digit
entering stages and will go out of this mode. Then try to perform emergency turn off once
more.
➢Producer of the car security systems Sharpshooter DV502 gives 36-
month warranty. The warranty period start from the date of purchase. If
the purchase documents are not present, warranty time is calculated
from the production date, which is shown on the sticker fixed on the
system block.
➢Warranty void if the system is remade not according the
recommendations of the producer the system is used not according its
purpose, if the system is installed improperly, if the signs mechanical,
electrical or chemical damage are present, if the device is affected by
the humidity and in all other cases, that are not related to the production
defects.
➢Producer does not give warranty for the fuses, capote switches, cases
of remote controls and batteries.
➢Producer is not responsible for the possible theft of the vehicle.
➢In case of warranty event the buyer must contact the company that
installed the security system into the vehicle.
➢Do not forget to check remote control batteries once a year. If the
decrease in the remote control working distance is noticed, the batteries
must be replaced. Use two batteries of type CR2016 (3V).
➢Regularly check the charge of the car battery (especially in winter). Due
to the insufficient charge of the battery the alarm may not turn off.
With the remote controls and a special receiver URC-4 you can control
other devices related with the remote signal transmission. I.e. open the
garage gate, the yard gate, the electromagnetic lock of the door, to turn
on/off the security system of the premises and so on. The receiver URC-4 is
made for this purpose. This receiver allows implement these very
comfortable functions. Contact the company that installed the system.
By this certificate I confirm that the security system was installed to the
vehicle in accordance with all recommendation of the producer.
Vehicle mark:
Type:
Serial number:
State registration number:
Vehicle security system Sharpshooter DV502
Installation performed:
Date:
Assembler address:
Assembler name, surname, position:
Sign:
Stamp:
V.207 2/2
Installation certificate
