Sharp RZ-X650 Manual de usuario

POS TERMINAL

KASSENTERMINAL

TERMINAL DE POINT DE VENTE

TERMINAL POS

HARDWARE OPERATION MANUAL

TECHNISCHE BEDIENUNGSANLEITUNG

MANUEL D'UTILISATION

MANUAL TECNICO

MODEL

MODELL

MODELE

MODELO RZ-X650

INTRODUCTION

IMPORTANT

Thank you very much for the purchase of a SHARP POS Terminal.

Please read this manual carefully before operating your POS Terminal.

Please keep this manual for future reference.

•Install this terminal in a location that is not subjected to direct radiation, unusual

temperature changes, and high humidity or exposure to water or other liquids.

Installation in such locations could cause damage to the cabinet and the electronic

components.

•Do not drop this terminal nor subject it to any strong shock.

This may cause damage to the terminal and the hard disk mounted in it.

•Do not apply excessive pressure to the display. Do not use a sharp-pointed object on

the display.

This may cause damage to the LCD display.

•The socket-outlet shall be installed near the equipment and shall be easily accessible.

For a complete electrical disconnection, remove the AC plug from the wall outlet.

•The terminal plugs into any standard wall outlet (official / nominal voltage).

Other electrical devices on the same electrical circuit could cause the terminal to

malfunction.

•Slots and openings in the cabinet and the back have been provided for ventilation.

To ensure the reliable operation of your system and protect it from overheating, these

openings must not be blocked or covered.

•Please observe the following when an optional drawer is used.

The drawer units should be securely fitted to the supporting platform to avoid

instability when the drawers are open.

English

•Please shut down the terminal and disconnect it from the AC supply before

connecting or disconnecting external devices to the COM ports. Note: Default voltage

at Pin 9 of COM2 / COM3 is 5V.

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in the mains lead of this apparatus may not correspond with

the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in

the plug which is marked by the letter Eor by the safety earth symbol or coloured

green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked

with the letter Nor coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked

with the letter Lor coloured red.

Ensure that your equipment is connected correctly - if you are in any doubt, consult a

qualified electrician.

"WARNING: THIS APPARATUS MUST BE EARTHED."

Noise level: 37,3 dB(A) Measured according to EN ISO 7779:2001

[Maximum value if the optional cash drawer springs open: 74,1 dB(A)]

GREEN-AND-YELLOW: Earth

BLUE: Neutral

BROWN: Live

TABLE OF CONTENTS

SYSTEM OVERVIEW 4

DISPLAY 7

BEFORE CALLING FOR SERVICE 8

LIST OF OPTIONS 8

SPECIFICATIONS 9

•The copyright of this manual belongs to SHARP Corporation.

•This manual may not be reproduced in whole or in part without the prior explicit

permission of SHARP Corporation.

Trademarks

•Intel is the registered trademark of Intel Corporation.

•Microsoft and Windows are registered trademarks of Microsoft Corporation.

•All other trademarks are the property of the respective company

SYSTEM OVERVIEW

Front view

Operation Display (Touch Panel)

15 inch TFT-LCD screen with touch sensitive screen. Displays the operational status of

the system and the system can be adjusted by touch screen.

Power button

After the terminal has been connected to the AC power supply push the power button

to turn on the terminal.

HDD indicator

LED lights up when the hard disk drive is reading data from or writing data to the drive.

Power indicator

LED lights up when the system is on

3 4 5

LCD brightness control

For adjustment of the screens brightness. (increase / decrease)

Magnetic Strip Reader(Optional)

For reading magnetic stripe cards.

Rear/IO Ports view

1 2 3 4 5 6 7 8

Serial Port 1, 2, 3

Connects serial devices such as a customer display, a barcode scanner, or a receipt printer

that use serial interface to the serial ports.

VGA Connector

Connects VGA signal cable from a 2nd monitor

Note:

•

DefaultvoltageatPin9ofCOM2/COM3is5V.Forfurtherinformation,pleasecontact

yourauthorizedSHARPdealer.

USB connectors

You can connect peripherals such as scanners, printers and keyboard to the USB

(Universal Serial Bus) connectors. USB peripherals are hot swappable enabling plug

and play for your peripherals.

LAN connector (RJ 45)

Connects the RJ-45 cable for 10/100/1000 Base Ethernet connection to this port.

Audio jack

An external amplified speaker may be connected to the jack for listening to sounds.

DC inlet Jack (for AC adaptor)

To supply power to the system, please connect here the supplied AC/DC power adaptor

(12V/5A).

DC outlet Jack (for future usage)

Cash Drawer Ports(2*3 pin Molex)

Optional Sharp cash drawers can be connected to the cash drawer port.

Parallel Port

Connect parallel devices such as a printer to the parallel port.

HDD rear cover

Remove the cover to install or replace the HDD. Consult your authorized SHARP dealer

for further details.

DISPLAY

Display angle

The display may be tilted for the best viewing angle. The angle can be adjusted within

140 degrees left/right and 45 degrees up/down as illustrated in the picture.

Caution:

•

Donotpullthedisplaybeyondthemaximumtiltanglenorapplyexcessivepressureto

thedisplay.

•

Makesuretoholdthebodywhenpullingthedisplaysothattheterminalmaynot

move.

•

TheLCDmodulebuiltinthisPOSterminalismanufacturedwithhighlyprecise

technology,howeverbrightpixelsorblankpixelsmayappear.Alsoanirregularcolor

andbrightnessmayoccurdependingontheviewangle.Pleasenotethatthistypeof

phenomenaiscommonforLCDsandmaynotbeamalfunction.

•

Thebacklightinthedisplayisaconsumablepart.

•

WhentheLCDdisplaycannolongerbeadjustedandbecomesdarker,youshould

replacetheLCDmodule.ConsultyourauthorizedSHARPdealerforfurtherdetails.

BEFORE CALLING FOR SERVICE

The condition shown in the below left-hand column does not necessarily indicate

functional faults of the terminal. Please check the listed items at the right-hand column

“Checking” before calling for service.

The following options are available for your POS terminal:

Do not try to install options yourself.

For details, contact your authorized SHARP dealer.

Condition Checking

The power indicator is not lit.

•IsACpoweravailableattheelectricaloutlet?

•IstheACplugoftheAC/DCadapter

connectedtotheelectricaloutlet?

•IstheACpowercorddisconnectedor

looselyconnectedtotheAC/DCAdapter?

•IstheACadaptersDCpowercable

connected to the DC inlet Jack of the POS

terminal?

•Isthepowerswitchoftheterminalturned

“ON”?

LIST OF OPTIONS

1. Magnetic card reader model RZ-X6MR1

2. 2 line rear customer display model RZ-X6DP1

3. Remote drawer models ER-03DW/04DW/05DW/03DWB4/05DWB5

4. The ER-48CC3 till is used for the ER-03DW/03DWB4

5. The ER-48CC2 till is used for the ER-04DW

6. The ER-58CC till is used for the ER-05DW/05DWB5

Otros manuales para RZ-X650

Tabla de contenidos

Idiomas:

Otros manuales de Terminal táctil de Sharp

Sharp

Sharp UP-820F Manual de usuario

Sharp

Sharp ER-A750 Manual de usuario

Sharp

Sharp UP-3500 Manual de usuario

Sharp

Sharp ER-A770 Manual de usuario

Sharp

Sharp UP-X300 Manual de usuario

Sharp

Sharp UP-5900 Manual de usuario

Sharp

Sharp ER-A750 Manual del propietario

Sharp

Sharp UP-3500 Manual de usuario

Sharp

Sharp UP-820N Manual de usuario

Sharp

Sharp UP-3300 Manual de usuario

Sharp

Sharp UP-3300 Manual de usuario

Sharp

Sharp ER-A771 Manual de usuario

Sharp

Sharp UP-5300 Manual de usuario

Sharp

Sharp ZQ-5000 Manual de usuario

Sharp

Sharp UP-3301 Manual del propietario

Sharp

Sharp ER-A770 Manual de usuario

Sharp

Sharp UP-X300CF256 Manual de usuario

Sharp

Sharp UP-3515 Manual de usuario

Sharp

Sharp UP-V5500 Manual de usuario

Sharp

Sharp UP-3300 Manual del propietario

Sharp

Sharp RZ-X650 Manual de usuario

Sharp

Sharp UP-X500 Manual de usuario

Sharp

Sharp UP-3301 Manual de usuario

Sharp

Sharp RZ-E601 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario