Sharkoon WPM Series Manual de usuario

WPM SERIES

MODULAR

ATX 2.0 POWER SUPPLY

Handbuch

Manual

Manuel d‘utilisation

Guia usario

Manuale d´istruzioni

Gebruiksaanwijzing

Guia usário

Instukcja obstugi

ユーザー　マニュアル

使用手冊

WPM SERIES

Content

1. Features 3

2. Speciﬁcations 4

2.1 Overview 4

2.2 Temperature range and humidity 5

2.3 Mains voltage and protective functions 5

2.4 Safety standards 5

2.5 Warranty period 5

3. Parts and accessories 6

4.The modular system of the PSU 7

4.1 The connectors at the PSU 7

4.2 The modular cables 7

5. Installation 8

5.1 Installing the PSU into a PC case 8

5.2 Connecting the PC components to the PSU 8

5.2.1 The connectors at a glance 8

5.2.2 Connecting mainboard and graphics card(s) 9

5.2.3 Connecting optical drives and other peripheral devices 10

5.2.4 Connecting the cables to the PSU 10

5.2.5 Checking all connections 10

6.Troubleshooting 11

7. Cable diagrams 11

WPM SERIES

Dear customer!

Congratulations for purchasing one premium quality SHARKOON product.

For a long life time and to take full advantage of this product we recommend that you read this manual

completely.

Have a good time with our product!

SHARKOONTechnologies

1. Features

ATX 12 V v.2.0:

Supports the latest Intel and AMD processor based systems.

High energy efﬁciency:

This power supply achieves an energy efﬁciency higher than 80%. This

value indicates the ratio (in percent) between energy input and output. The

closer this value reaches 100%, the less power dissipation does the PSU

produce.

Cable management:

The PSU provides a modular cable system. Thus only the

required cables need to be connected.

Active PFC function:

This power supply operates with active power factor correction (PFC).

140 mm fan:

The installed 140 mm fan provides a considerably higher airﬂow with lower

rpm, thus reducing the operating noise effectively.

PCIe connectors:

This power supply unit is equipped with one 6-pin and one 6+2-pin PCIe

connector.



WPM SERIES

WARNING

To prevent the risk of electric shock, do not open power supply housing. No

user-exchangeable parts inside. Refer service and maintenance to autho-

rized Sharkoon personnel. Warranty is void under unauthorized attempt to

open the power supply housing.

Suitable for indoor or ofﬁce use only.

Keep the power supply away from humidity!

2. Speciﬁcations

2.1 Overview



WPM SERIES

2.2 Temperature range and humidity

Operation 0 to +50 °C 20 – 90% rel. humidity, non-condensing

Storage -20 to +70 °C 5 – 95% rel. humidity, non-condensing

2.3 Line voltage and protective functions

This PSU works with 100 to 240 V (47/63 Hz) and is equipped with the following protective functions:

1. Over voltage protection:

The power supply provides a latch mode against over voltage, as deﬁned below:

+5 V 7 V

+3,3 V 4,3 V

+12 V 15,6 V

2. Short circuit protection:

The power supply is designed with a short circuit protection to prevent damage of the power supply

components. Main power will be shutdown when a short circuit occurs. The PSU will return to normal

after the short circuit has been removed and the main power switch has been turned off and back on

again, with a minimum cycle pause of 2 seconds.

3. Over current protection

2.4 Safety standards

Our power supply has been certiﬁed to comply with CB and CE safety regulations.

2.5 Warranty period

For this power supply unit we provide a 2 years warranty.



WPM SERIES

3. Parts and accessories

A – Power supply ”WPM400” or ”WPM500” or ”WPM600”

B – Power cord

C – Set with modular cables:

a – 1x PCIe cable with 1x 6-pin connector

b – 1x cable with 5x 4-pin peripheral connectors and 1x Floppy connector

c – 2x SATA cables with 3x 15-pin connectors each

D – Set with mounting screws

E – Cable bag

Note:

If you are missing any of the items listed above, please contact our customer service immediately:

[email protected] (Germany and Europe)

[email protected] (international).



A B C

WPM SERIES

4.The modular system of the PSU

The special feature of this PSUs is the so called cable management system to connect the peripheral

devices. Thanks to this modular system only the really required cables need to be connected thus keeping

your case proper and optimizing the airﬂow within.

4.1 The connectors at the PSU

A – 3x 6-pin connector for SATA and peripheral cables

(black)

B – 1x 6-pin connector for PCIe cables (red)

4.2 The modular cables

Besides the 20+4-pin ATX connector cable, a 4+4-pin P8 connector cable and a 6+2-pin PCIe cable – all

soldered to the PSU – the PSU is delivered with an extensive set of modular cables:

1x PCIe connector cable (6-pin PSU connector) for graphics cards

(1x 6-pin connectors)

1x connector cable for peripheral devices (6-pin PSU connector)

for optical drives (5 connectors) and ﬂoppy (1 connector)

2x SATA connector cables (6-pin PSU connector) for SATA drives

(3 connectors)



WPM SERIES

5. Installation

Remove an already installed PSU from the case. Proceed as follows:

1. Switch off your PC. Disconnect the PSU’s power cord from the wall outlet and your PSU. Unplug all

cables connected to the PC case (e.g. keyboard, mouse etc.).

2. Open the PC case (for additional information refer to the PC case’s manual).

3. Disconnect all cable connections between the PSU and other PC components (e.g mainboard, HDDs,

drives, fans etc.).

4. Remove the mounting screws connecting PSU and PC case and carefully take the PSU out of the case.

5.1 Installing the PSU into the PC case

1. Insert the PSU into the PC case and put it against the PSU bracket on the case’s back side.

2. Screw the PSU to the case from the outside using the included screws. Pay attention not to cover the

fan/air intake of the built-in PSU.

5.2 Connecting the PC components to the PSU

5.2.1 The connectors at a glance

Connector

20+4-pin ATX power

connector

4+4-pin P8 power con-

nector

6+2-pin PCIe power

connector

6-pin PCIe power con-

nector

Type 1x attached 1x attached 1x attached 1x modular

Connector

SATA power connector

4-pin connector for

peripheral devices 4-pin ﬂoppy connector

Type 6x modular 5x modular 1x modular



WPM SERIES

Note:

All connectors are designed fault-preventing to avoid misconnection. If you cannot attach the female

connector to the male connector of the drive or peripheral, please check if both connectors are attached in

the correct orientation.

Do not force to plug the female connector into the male connector in wrong orientation, nor modify any of

the components, as this will damage the PSU and your hardware. SHARKOON warranty does not cover

damage caused by incorrect handling.

5.2.2 Connecting mainboard and graphics card(s)

1. Plug the ATX power connector (ﬁg. 1) to the respective jack on the mainboard.

ﬁg. 1

2. In case your mainboard also provides an additional 4-pin or 4+4-pin power connector (the so called P4

resp. P8 connector), also plug the respective connector (ﬁg. 2).

ﬁg. 2

Note:

The power connection of the mainboard depends on the vendor and may vary. For detailed information

on how to establish the power connection refer to your mainboard’s manual.



WPM SERIES

3. In case your PCIe graphics card is equipped with an additional power connector, also plug the 6-pin

(ﬁg. 3a) or 6+2-pin (ﬁg. 3b) PCIe power connector which will provide a stable power support for your

graphics card.

ﬁg. 3a ﬁg. 3b

5.2.3 Connecting optical drives and other peripheral devices

1. Connect the 4-pin plug (ﬁg. 4), the SATA plug (ﬁg. 5) and the 4-pin ﬂoppy plug (ﬁg. 6) to the respective

peripheral devices.

ﬁg. 4 ﬁg. 5 ﬁg. 6

Note:

For more information refer to the respective manuals of your drives and peripheral devices.

5.2.4 Connecting the cables to the PSU

Finally connect the modular cables to the PSU according to the connector coding (see above 4.).

5.2.5 Checking all connections

Make sure that all devices are connected properly then plug the PSU’s power cord to a wall outlet and

switch the power supply on. This ends the installation of the PSU.



Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Sharkoon

Sharkoon

Sharkoon REBEL P30 Gold Manual de usuario

Sharkoon

Sharkoon WPC Bronze Series Manual de usuario

Sharkoon

Sharkoon SilentStorm Cool Zero 650 Manual de usuario

Sharkoon

Sharkoon SilentStorm SFX Gold Series Manual de usuario

Sharkoon

Sharkoon SHP650 Manual de usuario

Sharkoon

Sharkoon SilentStorm SFX Bronze 350 Manual de usuario

Sharkoon

Sharkoon SHP550 Manual de usuario

Sharkoon

Sharkoon Silent Storm SHA460-135A Manual de usuario

Sharkoon

Sharkoon QP500 Manual de usuario

Sharkoon

Sharkoon DRIVELINK COMBO USB3.0 Manual de usuario

Sharkoon

Sharkoon SilentStorm Icewind 550 Manual de usuario

Sharkoon

Sharkoon WPM Bronze 400 Manual de usuario

Sharkoon

Sharkoon SHP BRONZE Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario