Shark EP780C Manual de usuario

EP780C

www.sharkclean.com

Owner’s Guide

Manuel du

propriétaire

EP780C_42_IB_ENG_FRE_110418_1.indd 1 11-04-19 9:15 AM

TOLL FREE: 1-800-798-7398

This manual covers model:

EP780C 42

TECHNICAL SPECIFICATIONS

Voltage: 120V.

Watts: 1100W

Amps: 9 Amps

Hertz: 60Hz

Ce manuel couvre le numéro de modèle :

EP780C 42

SPÉCIFICATIONS TECHNIQUES

Voltage: 120V.

Watts: 1100W

Ampères: 9 ampères

Hertz: 60Hz

EP780C_42_IB_ENG_FRE_110418_1.indd 2 11-04-19 9:15 AM

TOLL FREE: 1-800-798-7398

1www.sharkclean.com

English

Contents

Important Safety Instructions 2

Getting Started 4

Assembly 4

Using the Vacuum 5

Using the Accessories 6

Maintenance 7

Troubleshooting 8

Replacement parts 8

Warranty and Registration 9

Thank you for

purchasing the

Shark® Quick

Clean Canister

vacuum.

Mesures de sécurité importantes 10

À faire au début 12

Assemblage 12

Utilisation de l’aspirateur 13

Nettoyer avec les accessoires 14

Entretien 15

Guide de dépannage 16

Pièces de remplacement 16

Garantie et enregistrement 17

Merci d’avoir

fait l’achat de

l’aspirateur-

traîneau

«Quick Clean»

de SharkMD.

Table des matières

EP780C_42_IB_ENG_FRE_110418_1.indd 1 11-04-19 9:15 AM

2 TOLL FREE: 1-800-798-7398

GENERAL ELECTRICAL SAFETY:

1. Unplug from electrical outlet when not in use

and before servicing.

2. DO NOT use vacuum with a damaged cord or

plug.

3. DO NOT pull or carry vacuum by the cord.

4. DO NOT unplug by pulling on cord; to unplug,

grasp the plug, not the cord.

5. DO NOT handle plug or vacuum cleaner with

wet hands.

6. DO NOT run the vacuum over the power cord.

7. DO NOT close a door on the cord.

8. DO NOT pull cord around sharp corners.

9. DO NOT leave appliance unattended while

plugged in.

10. Keep power cord away from heated surfaces.

11. Turn off all controls before plugging or

unplugging vacuum cleaner.

HOSE ATTACHMENTS:

12. DO NOT use if air ﬂow is restricted; if the air

paths or the hose become blocked, turn the

vacuum cleaner off. Remove all obstructions

before you turn on the unit again.

13. Keep the end of the hose and other openings

away from face and body.

14. Keep all suction openings away from hair, face,

ﬁngers, uncovered feet or loose clothing.

15. Only use manufacturer’s recommended

attachments.

WARNING:

TO REDUCE THE RISK OF ELECTRIC

SHOCK OR INJURY DO NOT USE

OUTDOORS OR ON WET SURFACES.

WHEN USING YOUR SHARK® QUICK

CLEAN CANISTER VACUUM, BASIC

SAFETY PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED, INCLUDING THE

FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING

YOUR SHARK® QUICK CLEAN CANISTER

VACUUM.

POLARIZED PLUG:

This appliance has a polarized plug (one blade

is wider than the other). As a safety feature, this

plug will ﬁt into a polarized outlet only one way.

Do not force into the outlet or try to

modify the plug to ﬁt.

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

EP780C_42_IB_ENG_FRE_110418_1.indd 2 11-04-19 9:15 AM

TOLL FREE: 1-800-798-7398

3www.sharkclean.com

English

GENERAL USE:

16. Use only as described in this manual.

17. DO NOT put any objects into openings.

18. Keep your work area well lit.

19. Keep the vacuum moving over the carpet

surface at all times to avoid damaging the

carpet ﬁbers.

20. DO NOT place vacuum on unstable surfaces

such as chairs or tables.

21. DO NOT allow young children to operate

the vacuum or use as a toy. Close attention

is necessary when used near children, pets or

plants.

22. DO NOT use vacuum cleaner if it has been

dropped, damaged, left outdoors or submerged

in water. To avoid the risk of electric shock,

do not disassemble or attempt to repair the

vacuum. Return to EURO-PRO Operating LLC

for examination, repair or adjustment. Incorrect

re-assembly can cause a risk of electric shock or

injury to persons when the vacuum is used.

DUST BAGS / FILTERS:

23. Before turning on the vacuum:

• Make sure that the ﬁlter and the dust bag,

are in place after routine maintenance.

• Make sure that all components and ﬁlters are

thoroughly dry after routine cleaning.

• Only use ﬁlters and accessories provided by

EURO-PRO Operating LLC [Failure to do so

will void the warranty].

GENERAL CLEANING:

24. DO NOT run the vacuum over large-sized

objects.

25. DO NOT pick up hard or sharp objects such as

glass, nails, screws or coins that could damage

the vacuum cleaner.

26. DO NOT pick up smoking or burning objects

such as hot coals, cigarette butts or matches.

27. DO NOT pick up ﬂammable or combustible

materials such as lighter ﬂuid, gasoline,

kerosene or use in areas where they may be

present.

28. DO NOT pick up toxic solutions such as

chlorine bleach, ammonia or drain cleaner.

29. DO NOT use in an enclosed space where

vapors are present from paint, paint thinner,

moth-prooﬁng substances, ﬂammable dust or

other explosive or toxic materials.

30. DO NOT vacuum up any liquids.

31. DO NOT immerse vacuum cleaner in water or

other liquids.

32. DO NOT use outdoors or on wet surfaces; use

only on dry surfaces.

33. Use extra care when cleaning on stairs.

34. Store your appliance indoors in a cool, dry area.

SAVE THESE

INSTRUCTIONS

EP780C_42_IB_ENG_FRE_110418_1.indd 3 11-04-19 9:15 AM

4 TOLL FREE: 1-800-798-7398

FIRST THING’S FIRST, YOU NEED TO

KNOW WHAT’S IN THE BOX YOU JUST

OPENED:

a Canister Vacuum

b Flexible Hose with Handle

c Upper Extension Tube

d Lower Extension Tube

e Floor Brush

f Combo Crevice/Dusting Tool

g Turbo Brush

Getting Started

YOUR SHARK® QUICK CLEAN CANISTER IS EASY TO

ASSEMBLE

1 Place your vacuum canister on a level surface

DO NOT plug in the vacuum until it is fully assembled.

2 Insert the ﬂexible hose (A) into the air intake duct. Push

it in until you hear it “click“, indicating that it is locked in

place. (Fig. 1)

3 Insert the upper extension tube (B) into the handle end of

the ﬂexible hose. (Fig. 1).

4 Insert the lower extension tube (C) into the upper

extension tube. (Fig. 1)

5 Push the end of the extension tube into the ﬂoor

brush (D). (Fig. 1)

6 The combo crevice/dusting tool (E) is stored in the back of

the vacuum next to the power cord. (Fig. 1)

Assembly

Fig. 1

EP780C_42_IB_ENG_FRE_110418_1.indd 4 11-04-19 9:15 AM

TOLL FREE: 1-800-798-7398

5www.sharkclean.com

English

1 To extend the power cord, pull

it from the rear of the vacuum

to the desired length. (Fig. 2) A

yellow mark on the power cord

shows the ideal cable length.

CAUTION: Do not pull the

power cord beyond the red

mark on the power cord as this

will damage the cord.

2 To retract the power cord, press

the cord rewind button. (Fig. 3)

If the cord does not fully retract,

pull it out a little and then press

the rewind button again.

WARNING: Always hold the

plug and DO NOT allow to

whip when rewinding

3 Plug the vacuum into an

electrical wall outlet.

4 Press the On/Off Button to the

“On” position to begin.

(Fig. 4)

5 Press the On/Off Button to the

“Off” position when ﬁnished

using the vacuum.

6 To store the canister vacuum,

insert the clip that is on the

back of the ﬂoor brush into the

slot on the back of the vacuum.

(Fig. 5)

Manual Suction Control

The Shark® Quick Clean Canister

vacuum includes a manual variable

suction control on the handle of

the hose. The suction power can

be adjusted by moving the slide

regulator to the desired position.

(Fig. 6) By opening the slide

regulator, the suction will be

reduced for vacuuming upholstery

and draperies. With the slide

regulator closed, you get maximum

suction for vacuuming carpets.

Using the Vacuum

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

EP780C_42_IB_ENG_FRE_110418_1.indd 5 11-04-19 9:15 AM

6 TOLL FREE: 1-800-798-7398

Using the Accessories

Using the Combo Crevice/Dusting

Tool

The Combo Crevice/Dusting tool

can be attached to either one or

both extension tubes for greater

reach or directly onto the handle.

1 Remove the ﬂoor brush from

the lower extension tube and

then depending on the length

that you desire, just push it in to

the end of the extension tube or

the handle. (Fig. 7)

Using the Turbo Brush

The Turbo Brush can be attached to

either one or both extension tubes

for greater reach or directly onto

the handle.

1 Remove the ﬂoor brush from

the lower extension tube and

then depending on the length

that you desire, just push it in to

the end of the extension tube or

the handle. (Fig. 8)

Note: The efﬁciency of your Turbo

Brush depends on the bristle brush

rotating at high speed. Strong air

action is needed to accomplish this.

In order to ensure that maximum air

suction is maintained:

a Change the dust bag

frequently.

b Replace the ﬁlter as needed.

c Ensure that the rotating

brush is kept free of hair and

debris which may accumulate

and decrease brush

performance.

Cleaning the Turbo Brush

From time to time, the turbine

of your turbo brush will require

cleaning.

1 Remove the Turbo Brush from

the hose or extension tube.

2 Turn the Turbo Brush over and

open the hinged cover to access

the turbine wheel. (Fig. 9)

3 There may be dust, lint, hair, etc

on the turbine wheel. Remove

as much of this as possible. Use

the vacuum with the hose to

remove any additional debris

that may remain.

Fig. 7 Fig. 8

Fig. 9

EP780C_42_IB_ENG_FRE_110418_1.indd 6 11-04-19 9:15 AM

TOLL FREE: 1-800-798-7398

7www.sharkclean.com

English

CAUTION:

To reduce the risk of shock, the

power cord must be disconnected

before removing or inserting the

dust bag.

Maintenance

Dust Bag Full Indicator:

The red dust bag full indicator may

turn on while you are vacuuming to

indicate that the dust bag is full and

needs to be replaced.

Replacing the Dust Bag:

1 Press the On/Off Button to the

“Off” position.

2 Remove the ﬂexible hose from

the vacuum by squeezing the

locking tabs on the neck of the

hose and pulling it out. (Fig. 10)

3 Place your ﬁngers underneath

the opening indentation behind

the vacuum handle and lift the

top cover up. (Fig. 11)

4 Hold the cardboard collar of the

dust bag and gently pull the

dust bag out. (Fig. 12)

5 Holding the cardboard collar,

insert a new dust bag into

the slots of the dust bag

compartment. (Fig. 13)

6 Close the top cover of the

vacuum.

Cleaning the Pre-Motor Filter:

1 Press the On/Off Button to the

“Off” position.

2 Open the top cover and pull the

pre-motor ﬁlter straight out.

(Fig. 14)

3 Wash the ﬁlter in lukewarm

water and allow to air dry

completely for 24 hours.

4 Slide a dry pre-motor into

position between the two posts

and the motor intake.

To Reset the Motor Thermostat:

Your Shark® Quick Clean Canister

vacuum is equipped with a protective

Motor Thermostat. If the motor

should overheat, the thermostat

shuts off the power.

1 Press the Power Button to turn

the unit “Off”.

2 Unplug the vacuum.

3 Check for clogged hose or ﬁlter;

unclog hose and replace ﬁlter.

4 Wait 45 minutes for vacuum to

cool; then plug in the vacuum.

5 Press the Power Switch to start

the vacuum.

Note: If vacuum still does not start,

contact Customer Service at:

1-800-798-7398.

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Fig. 14

EP780C_42_IB_ENG_FRE_110418_1.indd 7 11-04-19 9:15 AM

8 TOLL FREE: 1-800-798-7398

PROBLEM POSSIBLE REASONS & SOLUTIONS

Vacuum will not run.

Check to see if the vacuum is plugged in properly.

Check the circuit breaker/fuse.

Check the On/Off button.

Vacuum is not

picking up dirt.

Check the dust cup. It may need to be emptied.

Filter may need cleaning.

Check hose and accessories for blockages; clear blockages if required.

Airﬂow is restricted. No

suction or light suction.

Check hose and accessories for blockages; clear blockages if required.

Check the dust cup. It may need to be emptied.

Troubleshooting

WARNING:

to reduce the risk of electric shock, the power cord must be disconnected before

performing maintenance/troubleshooting checks.

Please call customer service if any servicing needs to be performed on the appliance at 1-800-798-7398.

Ordering Replacement Parts

To order additional parts and

accessories, go to

www.sharkclean.com

or call 1-800-798-7398.

PART PART NO.

Floor Brush 104FWI

Combo Crevice/Dusting Tool 105FPW

Turbo Brush 106FWI

Bag & Filter Kit XSB780C

Replacement Parts

EP780C_42_IB_ENG_FRE_110418_1.indd 8 11-04-19 9:15 AM

Tabla de contenidos

Idiomas:

Otros manuales de Aspiradora de Shark

Shark

Shark Powered Lift-Away DuoClean Zero-M ZU880... Manual de usuario

Shark

Shark NV355 Series Manual de usuario

Shark

Shark NV360K Manual de usuario

Shark

Shark DUOCLEAN SLIM UPRIGHT QU203Q Series Manual de usuario

Shark

Shark Rotator Speed Powered Lift Away NV682 Manual de usuario

Shark

Shark NV22L Manual de usuario

Shark

Shark Rotator Powered Lift-Away Speed Manual de usuario

Shark

Shark ROTATOR NV341 Series Manual de usuario

Shark

Shark 4400873618076 Manual de usuario

Shark

Shark ROTATOR NV401 Series Manual de usuario

Shark

Shark NV830 Series Manual de usuario

Shark

Shark Duoclean IF130EU Series Manual de usuario

Shark

Shark Vertex DuoClean PowerFins AZ2000 Series Manual de usuario

Shark

Shark Cordless Detect Pro Vacuum Manual de usuario

Shark

Shark APEX UpLight Corded Lift-Away QU602Q Series Manual de usuario

Shark

Shark ROCKET PowerFins UZ360 Series Manual de usuario

Shark

Shark NV22QUK Manual de usuario

Shark

Shark Lift-Away NV600UK Manual de usuario

Shark

Shark Steam Blaster EP905 Guía de referencia rápida

Shark

Shark Navigator Lift-Away NV351 Manual de usuario

Shark

Shark NV350NZ Manual de usuario

Shark

Shark DuoClean Powered Lift-Away Speed Manual de usuario

Shark

Shark NV350UK Series Manual de usuario

Shark

Shark Rotator Powered Lift-Away NV650 Series Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario

Nobles

Nobles 608669 Manual del producto