ShadeLab SHAN Manual de usuario
Assembly manual
INDEX
1 - INTRODUCTION ..............................................................p. 4
1.1 - Symbols used in the manual ....................................................... p. 4
1.2 - Personnel requirements .............................................................. p. 4
1.3 - Equipment necessary .................................................................p. 5
1.4 - Prior to assembly ........................................................................ p. 5
2 - SAFETY .......................................................................p. 6
2.1 - General safety information.......................................................... p. 6
2.2 - Working environment ................................................................. p. 6
3 - ASSEMBLY TECHNICAL TABLES ..........................................p. 7
3.1 - Table of minimum dimensions ....................................................p. 7
3.2 - Motor power table ...................................................................... p. 7
3.3 - Table of cutting dimensions ........................................................ p. 8
3.4 - Table of arms-central support brackets ...................................... p. 9
4 - SHAN COMPONENTS AND DIAGRAMS ..................................p. 11
4.1 - Tilting diagrams .......................................................................... p. 11
4.2 - Awning components ................................................................... p. 12
4.3 - Material necessary for assembly ................................................ p.
13
5 - AWNING ASSEMBLY ........................................................p. 14
6 - REGULATING THE AWNING ................................................p. 21
6.1 - Troubleshooting .......................................................................... p. 23
7 - REMOVING AND PACKING THE AWNING ................................p. 25
7.1 - Removing .................................................................................... p. 25
7.2 - Packing ....................................................................................... p. 25
4 | | ASSEMBLY
1 - INTRODUCTION
This “assembly manual” for SHAN awnings has been produced by SHADELAB to sup-
ply the indications necessary for the operations of assembling the components that
make up the product.
Assembly must be carried out by personnel with suitable technical and professional
qualifications, in accordance with the respective national laws or regulations (see Par.
1.2 “Personnel requirements”).
It is forbidden to eliminate, rewrite or alter the pages in the manual and their content.
This manual must be kept intact in all its parts, in an easily accessible place.
SHADELAB reserves the right to update the production and the respective manuals,
without being obliged to update the previous production and manuals.
SHADELAB reserves all rights to this manual: no total or partial reproduction is al-
lowed without authorisation in writing.
1.1 - Symbols used in the manual
Shown below are the WARNING symbols used in this manual:
IMPORTANT
Indications and advice to be observed to ensure a correct use of the awning. Failure to
follow these indications may endanger the integrity and/or resistance of the product.
ATTENTION
DANGER FOR THE OPERATOR! Instructions and indications to be assessed and fol-
lowed with care. Failure to follow these indications may endanger personal safety.
1.2 - Personnel requirements
The personnel appointed to perform this operation must possess a technical knowl-
edge of the product, acquired by assembling similar products for at least one year or
after having followed a suitable technical training course.
| ASSEMBLY | 5
1.3 - Equipment necessary
To ensure the correct assembly of the mechanical part, of the textile part, and conse-
quently the optimum operation of the finished product, it is necessary to be in pos-
session of the following equipment:
»fabric rolling frame;
»awning assembly frame with arms and vertically movable positioning bar;
»electric and pneumatic screwdriver;
»complete set of tools.
1.4 - Before starting assembly
IMPORTANT
Some components must be cut to suit the dimensions of the awning that is to be ob-
tained (see Par. 3.3 “Table of cutting dimensions”).
6 | | ASSEMBLY
2 - SAFETY
2.1 - General safety information
Follow these safety precautions:
ATTENTION
Wear the garments and personal protection equipment contemplated by the safety
regulations in force for the workplace (protective helmet, gloves, etc.).
ATTENTION
It is forbidden to use the awning to support yourself: risk of serious personal injury and
of damage to the awning.
IMPORTANT
Do not lay objects on the awning.
IMPORTANT
This manual is an integral part of the product. Before assembly, carefully read all the
instructions given in this manual.
IMPORTANT
SHADELAB guarantees the EC marking only for products supplied by the company itself.
If any parts have to be replaced with other components not guaranteed by SHADELAB,
the product guarantee will automatically become void and SHADELAB shall not answer
for any malfunctions of the product.
ATTENTION
Some awning components are constantly subject to strong pressure (arms) and, if the
instructions in this manual are not carefully followed, these components may cause
serious harm to persons and animals and damage to objects.
ATTENTION
NEVER reuse the arm lock after removing it.
2.2 - Working environment
At the moment of assembly, good natural and/or artificial lighting must be created in
the place where the work is being done.
| ASSEMBLY | 7
3 - ASSEMBLY TECHNICAL TABLES
3.1 - Table of minimum dimensions
Shan minimum dimensions
Arm projection [cm] Minimum width [cm]
150 199
175 224
200 249
225 274
250 299
275 324
300 349
325 374
350 399
375 424
400 449
Tab.1
3.2 - Motor power table
Width [cm]
200 300 400 500 600 700
Projections [cm]
150 15/17 N/m
175
25 N/m
200
225
250
30 N/m
275
300
325 35/40 N/m
350
375 50 N/m
400 60 N/m
Tab.2
IMPORTANT
For this awning model use motors with an electronic limit switch.
8 | | ASSEMBLY
3.3 - Table of cutting dimensions
Cutting dimensions
Component Type of control Size/measurement ratio
in [mm]
Cover
NICE MOTOR L -40
NICE MOTOR WITH EMERGENCY MANOEUVRE L -40
SOMFY MOTOR L -40
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -40
BECKER MOTOR L -40
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -40
Cassette
NICE MOTOR L -40
NICE MOTOR WITH EMERGENCY MANOEUVRE L -40
SOMFY MOTOR L -40
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -40
BECKER MOTOR L -40
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -40
Terminal bar
NICE MOTOR L -40
NICE MOTOR WITH EMERGENCY MANOEUVRE L -40
SOMFY MOTOR L -40
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -40
BECKER MOTOR L -40
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -40
Saddle
NICE MOTOR L -40
NICE MOTOR WITH EMERGENCY MANOEUVRE L -40
SOMFY MOTOR L -40
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -40
BECKER MOTOR L -40
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -40
Roller tube
NICE MOTOR L -130
NICE MOTOR WITH EMERGENCY MANOEUVRE L -130
SOMFY MOTOR L -129
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -134
BECKER MOTOR L -129
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -136
Fabric
NICE MOTOR L -150
NICE MOTOR WITH EMERGENCY MANOEUVRE L -150
SOMFY MOTOR L -149
SOMFY MOTOR WITH EMERGENCY MANOEUVRE L -154
BECKER MOTOR L -149
BECKER MOTOR WITH EMERGENCY MANOEUVRE L -156
Tab.3
| ASSEMBLY | 9
3.4 - Table of arms-central support brackets
Projections [cm]
Width [cm]
2 arms
251-300 301-350 351-400 401-450 451-500 501-550 (*) 551-600 (*)
A
max
n°
brackets
A
max
n°
brackets
A
max
n°
brackets
A
max
n°
brackets
A
max
n°
brackets
A
max
n°
brackets
A
max
n°
brackets
150 40 2 40 2 50 2 50 3 50 3 50 3 60 5
175 30 2 40 2 50 2 50 3 50 3 50 3 60 5
200 20 2 30 2 50 2 50 3 50 3 50 3 60 5
225 10 2 30 2 50 2 50 3 50 3 50 3 60 5
250 6 2 20 2 50 2 50 3 50 3 50 3 60 5
275 - - 10 2 40 2 50 3 50 3 50 3 60 5
300 - - 6 2 20 2 50 3 50 3 50 3 60 5
325 - - - - 10 2 40 3 50 3 50 3 60 5
350(*) - - - - 6 3 30 3 50 3 50 3 60 5
375(*) - - - - - - 10 3 40 3 50 3 60 5
400(*) - - - - - - 6 3 20 3 50 3 60 5
* add a central support Tab.4
fig.1
Cassette profile edge
Dimension B = 8 ÷ 9 cm.
10 | | ASSEMBLY
Projections [cm]
Width [cm]
601-650 (*) 651-700 (*)
3 arms 4 arms
n° brackets
3 arms 4 arms
n° brackets
A
max BA
max BA
max BA
max B
150 50 182 50 170 5 50 200 50 185 5
175 50 182 40 175 5 50 200 50 185 5
200 50 182 20 180 5 50 200 30 195 5
225 50 182 10 175 5 50 200 10 205 5
250 50 182 6 170 5 50 200 10 190 5
275 50 182 6 160 5 50 200 10 180 5
300 50 182 - - 5 50 200 6 172 5
325 30 195 - - 5 30 210 - - 5
350(*) 10 209 - - 5 20 218 - - 5
375(*) 10 209 - - 5 20 218 - - 5
400(*) - - - - 5 6 228 - - 5
* add a central support Tab.5
fig.2
Cassette profile edge
Cassette profile edge
Otros manuales para SHAN
1
Tabla de contenidos
Otros manuales de Accesorios de ShadeLab
