Servore SERVO GLAS 5000X Autolift Manual de usuario
User’s Manual
Auto-Darkening Welding Helmet
SERVO GLAS® 5000X Autolift
Made in Korea by
SERVORE CO.
#410-3 Tojin-ri Cheongbuk-myeon Pyeongtaek-si
Gyeonggi-do Korea.
TEL : +82-31-684-6952 ◆FAX : +82-31-684-6954
Home page: www.servore.com
E-mail: servore@servore.com
<1 page>
Instructions for use of SERVO GLAS® 5000X Autolift
Thank you for purchasing a Servo Glas® 5000X Autolift welding helmet.
Note
For your own protection, safety and to ensure the maximum
service life of your new helmet please read this manual
carefully before use. Misuse or abuse may result in injury or
reduced protection and may also void your warranty.
Safety is a personal responsibility. Servore endeavours to produce high quality
safety products that meet or exceed relevant Standards and provide appropriate
protection when used properly. Please help yourself and those around you by
using this product carefully and by exercising good judgement. Thank you.
1. Before Use
Servo Glas® 5000X Autolift
The auto darkening welding filter in the 5000X has been designed for arc
welding and gas cutting. It is suitable for all normal arc welding processes such
as MIG, MAG, TIG, SMAW, Plasma Arc and Air Carbon welding.
Before use the shade control should be adjusted to the appropriate level based
upon EN169 (European Standard specifications or equivalent) or other
appropriate safety guidelines. When in doubt please consult your safety
representative or your authorized Servo Glas® distributor.
The Servo Glas® 5000X Autolift provides continuous protection from ultraviolet
and infrared radiation to the maximum level indicated on the product and as
described in the relevant Standards. This protection is fail-safe and is not
compromised by loss of battery power or other electronic failure.
The Servo Glas® 5000X Autolift welding filter cartridge is fitted with two
independently operated sensors that detect the welding arc and respond
accordingly resulting in the appropriate darkened filter state as set by the user
and as indicated on the scaled adjustment. Please note that professional
judgement may be required to achieve the best results. When in doubt consult
an authorized safety representative or your Servo Glas® distributor and always
maintain a conservative attitude towards operation.
Two replaceable lithium batteries type CR2032 (3V) are used as major power
sources. An additional solar cell panel extends battery life and ensures efficient
operation. When operating normally the welding helmet will switch on
automatically and switch off automatically to save power a few minutes after the
last welding arc has been detected.
To provide a general check of system status you may wish to set the shade
control to 11 and hold the helmet towards a bright incandescent light
source. Under normal circumstances the filter will change from light to dark
state and back to light state again as you move the helmet away. Please note
that if you have any questions or there is any doubt about the performance of
your Servore product you should refer to your authorized safety representative
or Servo Glas® distributor.
Note
Always use genuine ServoGlas® front and inside cover
plates. Failure to do so may result in injury and will void
the warranty.
The ServoGlas® 5000X is not designed for overhead
welding without the use of additional protection.
Check your helmet for physical damage and test it
regularly. If your helmet is damaged or is not working
normally have it tested and repaired before use.
Always select the appropriate shade before use
according to the type of welding and current/amperes
used. When in doubt refer to your authorized safety
representative.
<2 page>
Helmet and Head harness Adjustment
Please make the appropriate adjustment(s) to the head harness to ensure a
comfortable and secure fit. It only takes a minute and helps ensure you are
properly protected. The ServoGlas® 5000X harness allows you to adjust the
distance and angle between your eyes and the filter window. You can also
adjust the circumference of the headband to ensure a comfortable but firm
fit. Please make these adjustments before use based on the illustrations in
figures shown below.
Note
•Genuine Servo Glas® front and inside cover plates must
always be used with Servo Glas® 5000X welding filter and
helmet. Failure to do so may result in injury and also void any
warranty.
•Servo Glas® 5000X is not designed for use in overhead
welding applications where additional protection may be
required.
•Check for normal operation of the auto-darkening welding
filter. If the welding filter does not darken in use stop welding
immediately.
•Always select the appropriate shade before use according to
the type of welding and current/amperes required. When in
doubt refer to your authorized safety representative.
2. Markings
The appropriate available shade number markings and range are indicated on
the product. Please ensure that the appropriate shade number is selected
before welding. Used properly the ServoGlas® 5000X provides eye and face
protection to meet or exceed EN379 and EN175 and other relevant Standards
where indicated. The following example illustrates these requirements. Please
note this example is provided for illustration purposes only.
CE 4 / 9 -13 SERVORE 2 / 1 / 2 / 379
Light shade
Dark shade
Manufacture identification
Optical class
Diffusion of light class
Variations in Luminous transmittance class
Certification mark or number of standard
ANNEX Ⅳ
CE CONFORMITY AND INFORMATION
The CE conformity marking shall consist of the initials ‘CE’ taking the following
form:
If the CE marking is reduced or enlarged the proportions given in the above
graduated drawing must be respected.
The various components of the CE marking must have substantially the same
vertical dimension, which may not be less than 5 mm. This minimum dimension
may be waived for small-scale PPE.
<3 page>
3. Parts List
The following parts are available from Servore and your authorized Servo
Glas® distributor.
<4 page>
No. Description No. Description
1 Helmet Shell 9A-2 Button Spring
2 Inner Protection Lens 9A-2 Button Spring
3 Magnifying Lens(108X51mm) 9-3 Button Washer
4A AutoLift Folder 9-4 Button Screw
4A-1 External Control 10 Hinge Cap Assembly
4-A-2 Wire Holder 10-1L Hinge Cap L
5 InsideCover Plate(108X51mm)
10-1R Hinge Cap R
6 Auto-darkening Filter Cartridge
10-2L Hinge Controller L
6-1 Battery (CR2032) 10-2R Hinge Controller R
7 Front Cover Plate(117X95mm) 10-3L Hinge Spring L
8 Front Cover 10-4R Hinge Spring R
9A Push Button Assembly 10-4 Hinge Cap Holder
9A-1 Push Button 10-5 Hinge Cap Screw
Helmet Knob Parts
Part No. Description Replacement of Knob Holder
HB Band Holder
Move P-bolt back and forth to
adjust the helmet distance
between eyes and filter window.
HK Helmet Knob Set
HK-1 P-bolt
HK-2 Band Holder
HK-3L Angular Stopper L
HK-3R Angular Stopper R
HK-4 Angular Washer
HK-5 Washer
HK-6 Knob
<5 page>
4. Technical Specifications
Switching time (light-dark) 1/25,000(0.04msec)
Shade Level
Inactivated Shade #4
Activated Shade #9 ~ #13
Sensitivity Adjustment Dual sensors plus pre-shading(Low-High)
Switching Delay(dark to light) Adjustable 0.05s – 0.8s
Tig rating RF(H) >1Amp / RF(L) >10Amp
Power supply 3V Lithium battery(CR2032)2ea(replaceable)
Battery life 3000 hours (Approximately)
Supplementary power Solar cells (Auto On/Off)
Battery replacement Replaceable(Low battery indicator)
Cartridge size 110×90mm (4.3×3.5 in)
Filter window 97×46mm (3.8×1.8 in)
Total weight Autolift : 610g(21.5 oz)
Operating temp. -5℃~ +55℃
Storage temp. -20℃~ +70℃
<6 page>
5. Control Function
PARTS 1.Solar Cell Panel 2. Sensor 3.LCD Filter Plate
4. Shade Control 5. Delay Control 6. Sensitivity Control
7. RF Sensor Switch 8.Low Battery Indicator
Otros manuales de Accesorios de soldadura de Servore
Manuales populares de Accesorios de soldadura de otras marcas
Miller Electric
Miller Electric OM-842 Manual de usuario
Miller
Miller A-200 Series Manual de usuario
Abicor Binzel
Abicor Binzel ABIMIG WT Series Manual de usuario
optrel
optrel lifeflip autopilot Manual de usuario
Miller
Miller MIGmatic M-25 Manual de usuario
Tregaskiss
Tregaskiss TOUGH GUN TT3 Reamer Manual de usuario
