Sercomm RP052M Manual de usuario
i
RP052M
WiFi EasyMesh
Router
ii
User Guide
Table of Contents
CHAPTER 1 INTRODUCTION..............................................................................................1
Package Contents ..............................................................................................................1
Features..............................................................................................................................1
LEDs...................................................................................................................................2
CHAPTER 2 INITIAL INSTALLATION ..............................................................................4
Requirements.....................................................................................................................4
Procedure...........................................................................................................................4
CHAPTER 3 EASYMESH CONFIGURATION ...................................................................5
Configuration.....................................................................................................................5
APPENDIX A SPECIFICATIONS........................................................................................11
WiFi EasyMesh Router...................................................................................................11
APPENDIX B FCC STATEMENT .......................................................................................12
Copyright 2019. All Rights Reserved.
Document Version: 1.2
All trademarks and trade names are the properties of their respective owners.
1
Chapter 1
Introduction
This Chapter provides an overview of the WiFi EasyMesh Router features and
capabilities.
Congratulations on the purchase of your new WiFi EasyMesh Router. The WiFi EasyMesh
Router is a consumer electronic device, which is designed to extend WiFi signal and provide
seamless WiFi coverage throughout your home. Compliance with WFA MAP (also called
EasyMesh) standard, it enables inter-operability across WiFi access points from different
vendors. It is simple for consumers to deploy WiFi mesh network by just pressing one button.
Package Contents
The following items should be included:
WiFi EasyMesh Router Unit x 1
Power Adapter x 1
Ethernet Cable x 1
If any of the above items are damaged or missing, please contact your dealer immediately.
Features
MT7621DAT processor with 64MB Flash and 128MB RAM
Two 10/100/1000 Ethernet ports with RJ45 connector
Internal antenna for WiFi
1
2
LEDs
Front Panel
The WiFi EasyMesh Router has 4 LEDs.
POWER
(Green)
On - Power On/Normal Operation
Off - Power Off
Blinking –Device is performing factory reset
WiFi
(Green)
On - WiFi function is enabled
Off –WiFi function is disabled
Blinking –WPS onboarding is processing
WAN
(Green)
On –Device is connected to Internet
Off –Device is not connected to Internet
Error-indication
(Red)
On –Abnormal situation happened (i.e. failed to connect to
Internet)
Off –Device works normally
3
Rear/Side Panel
Power Port
Connect the supplied power adapter here.
ETHERNET
Port
There are two Ethernet ports in the device: WAN and LAN ports.
WAN Port. It is used to connect to generic homer router or ADSL
modem for Internet access.
LAN Port. It is used to connect to other WiFI EasyMesh routers
with physical wire.
Reset
This button has two (2) functions:
Reboot. When pressed and released, the WiFi EasyMesh router
will reboot (restart).
Clear All Data. This button can also be used to clear ALL data
and restore ALL settings to the factory default values.
To Clear All Date and restore the factory default values:
1. Power On.
2. Keep holding the Reset Button down for 10 seconds.
Release the Reset Button. The power LED will blink and device will
clear all data and restore all settings to default values.
WPS Button
Push the WPS button for 4~5 seconds to trigger WPS based MAP
onboarding process.
During the onboarding process, the WiFi LED will blink till the
process is completed
4
Chapter 2
Initial Installation
This Chapter covers the software installation of the WiFi EasyMesh Router.
Requirements
Use a standard 10/100/1000 BaseT network (UTP) cable with RJ45 connector for Internet
connection.
Procedure
1. Choose an Installation Site
Select a suitable place to install the WiFi EasyMesh Router.
2. Connect WAN Cable
Use a standard Ethernet cable to connect the device to the WAN port on WiFi EasyMesh
Router. And the other side of Ethernet cable is connected to Home Router or ADSL mo-
dem for Internet connection.
3. Power Up
Connect the supplied power adapter to the WiFi EasyMesh Router. Use only the power
adapter provided. Using a different one may cause hardware damage.
4. Check the LEDs
The Power LED should be ON.
The WiFi LED should be ON
The WAN LED should be ON.
2
5
Chapter 3
EasyMesh Configuration
This Chapter provides Setup details of the WiFi EasyMesh Router.
Configuration
User can configure WiFi EasyMesh Router through Web GUI on Router via WiFi or Ethernet
LAN interface.
In following example, we will show you how to configure WiFi EasyMesh function through
Ethernet LAN to deploy mesh network.
Change device role to be Controller
As all WiFi EasyMesh Routers are configured as Agent by default, therefore, before deploying
mesh network, user has to select one of WiFi EasyMesh Routers (we will called this device
“Controller”in later section) to play as Controller.
Below steps will guide you how to change device role to be Controller
Connect Ethernet Cable to LAN port of WiFi EasyMesh Router and the other side of cable
is connected to PC.
Login into Web GUI of WiFi EasyMesh Router via PC browser.
(IP address: http://192.168.1.1)
Before access Home page, you need to enter Username/ Password.
(Both default Username and Password are “root”)
3
6
In Home page, go to Sercomm->EasyMesh
After entering EasyMesh page, please select device role as “Controller”and then click
“Save and Apply”button.
The WiFi EasyMesh Router will start applying settings to change device to be Controller.
Appendix B - About Wireless LANs
7
Once finished, you can find the WiFi EasyMesh has been changed to Controller (as below
red rectangle).
User can also find the WiFi EasyMesh Router has been changed to Controller and User’s
PC is connected to Controller in network topology by clicking “Display Runtime Topolo-
gy”button.
8
WPS onboarding for deploying mesh network
In this section, we will guide user how to perform WPS onboarding to establish connection
between Controller and another WiFi EasyMesh Router(we will call this devic “Agent”in later
section) to deploy mesh network.
Below are steps to deploy mesh network.
Press WPS button on both Controller and Agent for about 4~5 seconds and then release.
Once WPS onboarding process is triggered, the WiFi LED will blink until the process is
completed.
After finishing WPS onboarding process, you will find the Agent is connected to the
Controller in network topology.
User can repeat the same steps to add more Agents in mesh network to extend WiFi
coverage.
Tabla de contenidos
Otros manuales de Enrutador inalámbrico de Sercomm
