SentexSystems Clikcard-SA Guía rápida

Doc - 6001131

Rev - B

BASIC

PROGRAMMING AND USE

INSTRUCTIONS

FOR THE

Clikcard-SA SYSTEM

Rev. B Doc. 6001131 Page 1 of 5

IMPORTANT NOTICE

This manual describes the basic system functions that need to be programmed for the Clikcard-SA

system to function properly. If you wish to program the system’s more advanced features (i.e. time zones,

automatic lock/unlock schedules, baud rate speed, etc.), please refer to the enclosed manual titled “USING

THE MORE ADVANCED FEATURES OF THE Clikcard-SA SYSTEM”.

The Clikcard-SA system is very reliable and easy to use. However, if programmed incorrectly, the

system may function improperly and is likely to cause you and others a great deal of inconvenience. Similarly,

there are certain key things you must know about using this system. Thus, you should take the time to read

these instructions completely before attempting to program or use your system. If you have any questions,

your installing dealer will be happy to assist you.

TABLE OF CONTENTS

This document is divided into four sections as follows:

SECTION NAME PAGE

1 - Basic Hints/Programming Rules 2

2 - Entering and Exiting Program Mode 3

3 - Entering and Erasing Transmitters 4

4 - Verifying Entries 5

IMPORTANT NOTE: The Sentex Systems warranty on this system is conditional upon Sentex Systems being paid in full

for this equipment. This warranty will not be honored until such payment has been received by Sentex Systems.

THIS DOCUMENT IS PROTECTED BY COPYRIGHT, AND MAY NOT BE COPIED OR ADAPTED WITHOUT THE

PRIOR CONSENT OF SENTEX. THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY TO SENTEX AND

SUCH INFORMATION MAY NOT BE DISTRIBUTED WITHOUT THE PRIOR WRITTEN CONSENT OF SENTEX. THE

FIRMWARE INCLUDED IN THE Clikcard-SA SYSTEM AS THEY RELATE TO THIS DOCUMENTATION ARE ALSO

PROTECTED BY COPYRIGHT AND CONTAIN INFORMATION PROPRIETARY TO SENTEX.

Sentex Systems

Chatsworth, CA

Visit us at www.sentexsystems.com

Page 2 of 5 Doc. 6001131 Rev. B

1 - BASIC HINTS AND PROGRAMMING RULES

The sections that follow provide detailed explanations of how to program the system’s basic functions.

However, there are a number of basic hints and programming rules that apply to the programming of any step.

These are listed below:

1. All programming is done through the system’s keypad which is located inside the receiver’s

enclosure.

2. The first step in programming is to enter the program mode (see Page 3). Once you are in this

mode, the system will remain in this mode until you tell it to exit to the “run” mode, or until 60

seconds pass without an entry on the keypad (so you do not accidentally leave it in the program

mode).

3. The Clikcard-SA system provides visual feedback as you program. If you make an “error”, the

system will display the following:

CODE MEANING OF CODE

E1 The entry you are trying to erase or verify does not exist in

the system. For example, there is no transmitter code that

matches the one you are trying to erase.

E2 You have tried to enter a transmitter that already exists in

the system’s memory. For example, you are trying to enter

transmitter number 253 and that code has already been

entered into the system.

E3 The system’s memory is already full. You must either

erase a single transmitter or the entire system’s memory.

E4 You have made a format error in your entry. For example,

you have tried to enter a “✱“as part of a transmitter

number.

Once the feedback is completed, you may continue with your next entry or correct the entry you

have just attempted.

4. Always keep track of what transmitter numbers you have entered into the system and to whom they

have been assigned. This will allow you to void a transmitter as soon as somebody is no longer

allowed access to your building or complex, or if a transmitter is lost.

5. If you realize in the middle of an entry that you are making a mistake, you can abort the transaction

by entering a “✱

✱✱

✱“.

6. If you are in the programming mode, the system will display a “P” on the seven-segment display.

Rev. B Doc. 6001131 Page 3 of 5

2 - ENTERING AND EXITING PROGRAM MODE

The sequences described in this section allow you to enter and exit the program mode, as well as to

change the code that must be used to gain access to this mode.

ENTERING PROGRAM MODE

Format “✱✱✱

✱✱✱✱✱✱

✱✱✱“ + programming access code (6 digits)

Example “✱✱✱

✱✱✱✱✱✱

✱✱✱“ + 000000

Important Factory setting is 000000. We suggest you change this code to maintain the security of your

Notes system.

CHANGING THE PROGRAMMING ACCESS CODE

Purpose To make sure that the code required to enter the program mode is known only by authorized

personnel.

Format 09 + new programming access code (6 digits) + “#”

Example 09 + 123456 + #

Important Once you have changed the programming access code, it is imperative that you verify the new

Note code before you exit the programming mode. This is to ensure that an error was not made when

the code was changed.

VERIFYING THE PROGRAMMING ACCESS CODE

Purpose To verify that the programming access code is correct. You must perform this step after changing

the programming access code, but before you exit the programming mode.

Format 10 + programming access code (6 digits) + “#”

Example 10 + 123456 + #

Important If a “0” is displayed on the 7-segment display, then the programming access code is correct.

Notes If you receive an “E1” response, the programming access code is incorrect, in which case you

should either re-verify the code (in case an error was made the first time) or change the code

before exiting the programming mode.

EXITING PROGRAM MODE

Format 00 + “#”

Important Once you press the “#” key, the system will return you to the “run” mode and the display will go

Notes blank.

Page 4 of 5 Doc. 6001131 Rev. B

3 - ENTERING AND ERASING TRANSMITTERS

The sequences described in this section allow you to tell the system which transmitters should grant

entry. These programming steps will be repeated frequently as people move in and out of your

building/complex.

ENTERING A SINGLE TRANSMITTER

Purpose Allows you to validate a single transmitter number to open relay 1 only.

Format 14 + transmitter number (up to 5 digits) + “#”.

Example 14 + 12345 + # (sets up transmitter number 12345 to activate relay 1).

Important The transmitter number is the code that will be emitted from the transmitter when a button is

Notes pressed. This number is always five digits in length, but if the preceding numbers are zero’s (for

example, 00007), you do not have to enter the leading zeros. For example, if your transmitter

number is 00007, you may enter either “00007” or “7” as the transmitter number. But, if your

transmitter number is 12345, you must enter “12345” as the transmitter number.

If you want a transmitter to activate relays 2 and 3 or if you want to restrict the access of a specific

transmitter to specific times or days, please refer to section 5 of the enclosed manual titled “USING

THE MORE ADVANCED FEATURES OF THE Clikcard-SA SYSTEM.”

ENTERING A GROUP OF TRANSMITTERS

Purpose Allows you to load a group of transmitter numbers to open relay 1 only in one easy step rather than

loading each transmitter individually.

Format 15 + beginning transmitter number (5 digits) + ending transmitter number (5 digits) + “#”.

Example 15+00007+00052 + # (sets up transmitter numbers 00007 through 00052 to activate relay 1).

Important For this step, the number that you enter as the beginning and ending transmitter numbers must be

Notes entered as 5 digits.

Transmitters that are validated as part of a group may be deleted individually.

If you want the transmitters to activate relays 2 and 3 or if you want to restrict the access of the

transmitters to specific times or days, please refer to page 9 of the enclosed manual titled “USING

THE MORE ADVANCED FEATURES OF THE Clikcard-SA SYSTEM.”

ERASING A SINGLE TRANSMITTER

Purpose Allows you to remove a single transmitter from the system’s memory.

Format 16 + transmitter number (up to 5 digits) + “#”.

Example 16 + 12345 + # (removed transmitter number 12345 from the system’s memory).

Rev. B Doc. 6001131 Page 5 of 5

4 - VERIFYING ENTRIES

The steps in this section will allow you to verify the transmitters that are currently programmed in your

system.

VERIFYING A TRANSMITTER NUMBER

Purpose Allows you to verify if a transmitter has been programmed into the system.

Format 18 + transmitter number (up to 5 digits) + “#”

Example 18 + 12345 + #

Important If a transmitter number is valid in the system, the system will display “1000”. If a transmitter

Notes number is not valid in the system, the system will display the error message “E1”.

Tabla de contenidos

Otros manuales de Receptor de SentexSystems

SentexSystems

SentexSystems ClikCard Especificaciones técnicas

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario