Sentera Controls DSMHM-2R Manual de servicio

Mounting and operating instructions

DSMHM-2R MULTIFUNCTIONAL

DUCT TRANSMITTER

WITH CORROSION

PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 2 - 9

Table of contents

SAFETY AND PRECAUTIONS 3

PRODUCT DESCRIPTION 4

ARTICLE CODES 4

INTENDED AREA OF USE 4

TECHNICAL DATA 4

STANDARDS 4

OPERATIONAL DIAGRAMS 5

WIRING AND CONNECTIONS 5

MOUNTING & OPERATING INSTRUCTIONS IN STEPS 6

OPERATING INSTRUCTIONS 8

VERIFICATION OF INSTALLATION 9

TRANSPORT AND STORAGE 9

WARRANTY AND RESTRICTIONS 9

MAINTENANCE 9

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 3 - 9

back to the table of contents

SAFETY AND PRECAUTIONS

Read all the information, the datasheet, mounting and operating instructions and

study the wiring and connection diagram before working with the product. For

personal and equipment safety, and for optimum product performance, make sure you

entirely understand the contents before installing, using, or maintaining this product.

For safety and licensing (CE) reasons, unauthorised conversion and/ or modiﬁcations

of the product are inadmissible.

e product should not be exposed to abnormal conditions, such as extreme

temperatures, direct sunlight or vibrations. Long-term exposure to chemical

vapours in high concentration can aﬀect the product performance. Make sure the

work environment is as dry as possible; avoid condensation.

All installations shall comply with local health and safety regulations and local

electrical standards and approved codes. is product can only be installed by

an engineer or a technician who has expert knowledge of the product and safety

precautions.

Avoid contacts with energised electrical parts. Always disconnect the power

supply before connecting, servicing or repairing the product.

Always verify that you apply appropriate power supply to the product and use

appropriate wire size and characteristics. Make sure that all the screws and nuts

are well tightened and fuses (if any) are ﬁtted well.

Recycling of equipment and packaging should be taken into consideration and these

should be disposed of in accordance with local and national legislation/regulations.

In case there are any questions that are not answered, please contact your

technical support or consult a professional.

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 4 - 9

back to the table of contents

PRODUCT DESCRIPTION

e DSMHM-2R are multifunctional duct transmitters which measure temperature,

relative humidity and CO2concentration. ey are treated with anti-corrosion

and ammonia resistant coating that makes them suitable for applications in the

agriculture and horticulture industry or other harsh environments. Based on the

temperature and relative humidity measurements, the dew point is calculated. ey

are Power over Modbus supplied and all parameters are accessible via Modbus RTU.

ARTICLE CODES

Code Supply Connection

DSMHM-2R Power over Modbus, 24 VDC RJ45

INTENDED AREA OF USE

■Monitoring temperature, relative humidity and CO2level in air ducts

■Suitable for harsh environments. Application ﬁeld: greenhouses, livestock breeding

farms, mushroom growing houses, etc.

TECHNICAL DATA

■Selectable temperature range: -30—70 °C

■Selectable relative humidity range: 0—100 %

■Selectable CO2range: 0—10.000 ppm

■Accuracy: ±0,4 °C (range -30—70 °C); ±3 % rH (range 0—100 % rH); ±30 ppm CO2

(range 400—5.000 ppm)

■Maximum power consumption: 1,08 W

■Nominal power consumption in normal operation: 0,81 W

■Imax: 45 mA

■Replaceable CO2sensor element

■Minimum airﬂow velocity required: 1 m/s

■Enclosure and probe material:

►ASA, grey (RAL9002)

■Protection standard: enclosure: IP54, probe: IP20

■Typical ﬁeld of use:

►temperature: -30—70 °C

►rel. humidity: 0—100 % rH, (non-condensing)

►CO2: 400—5.000 ppm

■Storage temperature: -10—60 °C

STANDARDS

■EMC Directive 2014/30/EC:

►EN 61326-1:2013 Electrical equipment for measurement, control and laboratory

use - EMC requirements - Part 1: General requirements

►EN 61326-2-3:2013 Electrical equipment for measurement, control and

laboratory use - EMC requirements - Part 2-3: Particular requirements - Test

conﬁguration, operational conditions and performance criteria for transducers

with integrated or remote signal conditioning

■High protective conformal coating

►MIL-I-46058C qualiﬁed

►IPC-CC-830

■WEEE Direc tive 2012/19/EC

■RoHs Directive 2011/65/EC and EPA 33/50 compliant

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 5 - 9

back to the table of contents

OPERATIONAL DIAGRAMS

Input register

1 [%]

100

-30 Min

range

Max

range

70 T [°C]

Input register

11 [%]

100

0 Min

range

Max

range

100 rH [%]

Input register

22 [%]

100

0 Min

range

Max

range

10.000 CO2[ppm]

WIRING AND CONNECTIONS

RJ45 socket (Power over Modbus)

Pin 1 24 VDC Supply voltage

Pin 2

Pin 3 AModbus RTU communication, signal A

Pin 4

Pin 5 /B Modbus RTU communication, signal /B

Pin 6

Pin 7 GND Ground, supply voltage

Pin 8

GND

24 VDC

8 mm

RJ45

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 6 - 9

back to the table of contents

MOUNTING & OPERATING INSTRUCTIONS IN STEPS

Before you start mounting the unit, read carefully “Safety and Precautions”.

Follow these steps:

1. When preparing to mount the unit, bear in mind that the probe opening must

be positioned in the centre of the duct. Always use the ﬂange to install the

sensor on round ducts. It is possible to install the sensor without the ﬂange on

rectangular ducts (if necessary), see Fig. 1 and Fig. 2 below.

Fig. 1 Mounting dimensions

With ﬂange Without ﬂange

Ø 12

2x Ø 5

86,8

18,5

42,3

285

Probe

opening

243

34,5

4x Ø 4,

100

105

Fig. 2 Mounting position

Correct Incorrect

AIR FLOW AIR FLOW

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 7 - 9

back to the table of contents

2. Having selected the appropriate mounting location, proceed with the following steps:

2.1 Drill a tight-sealing Ø 13 mm hole into the duct.

2.2 Fix the ﬂange onto the duct outer surface using the self-drilling screws

delivered with the unit. If you do not intend to use the ﬂange, insert the

probe and ﬁx the enclosure onto the duct. Mind the airﬂow direction (see

Fig. 2 and Fig. 3).

Fig. 3 Mounting requirements

7,5*D(1)3,5*D

(1)D = Duct diameter

ATTENTION Installation requirements: e unit must not be installed in turbulent air zones. Ensure

suﬃciently long settling zones upstream and downstream of the tapping point. A

settling zone consists of a straight section of pipe or duct with no obstructions. Avoid

installation near ﬁlters, cooling coils, fans, etc. e sensor will achieve the optimal

result when the measurement is taken at least 7,5 duct diameters downstream and

at least 3 duct diameters upstream from any turns or ﬂow obstructions.

ATTENTION Installation of the unit near high EMI-emitting devices may lead to faulty

measurements. Use shielded wiring in areas with high EMI.

ATTENTION Keep at least 15 cm distance between the sensor lines and the 230 VAC power lines.

2.3 Install the probe at the desired depth and; in case you use the ﬂange, ﬁx it

via the plastic white screw in the ﬂexible ﬂange.

2.4 Unscrew the cover of the unit to remove it and insert the connecting cables

through the cable gland of theunit.

2.5 Crimp the RJ45 cable and plug it into the socket, see Fig.4 and section

“Wiring and connections”.

Fig. 4 Wiring and connections

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 8 - 9

back to the table of contents

3. Close the enclosure and ﬁx the cover. Tighten the cable gland to retain the IP

rating of the enclosure.

4. Switch on the power supply.

5. Customise the factory settings to the desired ones via the 3SModbus software

or Sensistant (if necessary). For the default factory setting, see the Modbus

For the complete Modbus register data, refer to the product Modbus Register

Map, which is a separate document attached to the article code on the website

and contains the registers list. Products with earlier ﬁrmware versions may not be

compatible with this list.

NOTE

Optional settings

To assure correct communication, the NBT needs to be activated in only two devices

on the Modbus RTU network. If necessary, enable the NBT resistor via 3SModbus or

Sensistant (Holding register 9).

Example 1 Example 2

ТX

NBT

Slave 2

Master

Slave n

Slave 1

Slave 2

Slave 1

ТX

NBT

Master

Slave n

NOTE On a Modbus RTU network, two bus terminators (NBTs) need to be activated.

CAUTION Do not expose to direct sunlight!

OPERATING INSTRUCTIONS

NOTE For detailed information and settings, refer to the product Modbus register map,

which is attached to the article code on our website.

Calibration procedure:

Sensor calibration is not necessary.

In the unlikely event of CO2sensor element failure, this component can be replaced.

All sensor elements are calibrated and tested in our factory.

Bootloader

anks to the bootloader functionality, the unit ﬁrmware can be updated via Modbus

RTU communication. With 3SM boot Application (part of 3SM center software

suite), ‘boot mode’ is automatically activated and the ﬁrmware can be updated.

NOTE Make sure the power supply does not get interrupted during “bootload” procedure,

otherwise you risk losing unsaved data.

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

www.sentera.eu

MIW-DSMHM-2R-EN-000 - 12 / 03 / 2020 9 - 9

back to the table of contents

VERIFICATION OF INSTALLATION

If your unit does not function as expected, please check the connections.

TRANSPORT AND STORAGE

Avoid shocks and extreme conditions; stock in original packing.

WARRANTY AND RESTRICTIONS

Two years from the delivery date against defects in manufacturing. Any modiﬁcations

or alterations to the product after the date of publication relieve the manufacturer

of any responsibilities. e manufacturer bears no responsibility for any misprints or

mistakes in this data.

MAINTENANCE

In normal conditions this product is maintenance-free. If soiled, clean with a dry or

damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these

circumstances the unit should be disconnected from the supply. Pay attention that

no ﬂuids enter the unit. Only reconnect it to the supply when it is completelydry.

DSMHM-2R

MULTIFUNCTIONAL DUCT TRANSMITTER

WITH CORROSION PROTECTION

Tabla de contenidos

Otros manuales de Transmisor de Sentera Controls

Sentera Controls

Sentera Controls HPS-X-LP Manual de servicio

Sentera Controls

Sentera Controls RSTHM-2 Manual de servicio

Sentera Controls

Sentera Controls SPS series Manual de servicio

Sentera Controls

Sentera Controls DSMFM-2R Manual de servicio

Sentera Controls

Sentera Controls DSMFX-2R Manual de servicio

Sentera Controls

Sentera Controls RSTH 2 Series Manual de servicio

Sentera Controls

Sentera Controls RSTHX-2 Manual de servicio

Sentera Controls

Sentera Controls DSTHG-2 Manual de servicio

Sentera Controls

Sentera Controls SPD Manual de servicio

Sentera Controls

Sentera Controls HPD Manual de servicio

Sentera Controls

Sentera Controls DSTHM-2 Manual de servicio

Sentera Controls

Sentera Controls RSMF-2R Series Manual de servicio

Sentera Controls

Sentera Controls RSMFX-3 Manual de servicio

Sentera Controls

Sentera Controls DPS-M-LP Manual de servicio

Sentera Controls

Sentera Controls RSMFH-2R Manual de servicio

Sentera Controls

Sentera Controls DPD-F-1K0 Manual de servicio

Sentera Controls

Sentera Controls DSVCX-R Manual de servicio

Sentera Controls

Sentera Controls HPS-X -2 Manual de servicio

Sentera Controls

Sentera Controls RSMFH-3 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario