Sensio SE9080HD Manual de usuario

1 x Fitting Instructions

HD LED

In-CabInEt

LIgHt wItH

IR SEnSoR

CODE: SE9080HD

Components

Important safety information

Tools required

INSTALLATION

INSTRUCTIONS

IMPORTANT: please read these instructions before commencing installation and retain for future reference.

1 x SE9080HD HD LED In-Cabinet Light

with mounting bracket and cable

Please read these instructions carefully before attempting to install

this product. It is advisable to keep these instructions in a safe place

for further reference.

We recommend that you consult a qualiﬁed electrician.

All electrical installations must be carried out in accordance

with current IEE wiring regulations (BS7671).

These products must not be modiﬁed, if any modiﬁcations are

made, it may invalidate the warranty and may render the product

unsafe. These LED lights operate low voltage (24V).

Do not wire the individual LED light ﬁttings directly to the mains.

This product is for indoor use only. Keep out of moisture and use

only in dry rooms.

• If in doubt installation must be carried out by a qualiﬁed

electrician.

• Install on smooth ﬂat surface(s) only.

• The Wattage of this product is 2W. Make sure that

the LED driver used with these ﬁttings has an adequate

max wattage.

• We recommend using a SE40553 15W LED Driver with this ﬁtting.

You will be able to run a maximum of 3 ﬁttings per driver.

•for more fittings, use the SE40555 15W 24V LED Driver. You will

be able to run a maximum of 6 ﬁttings per driver.

Safety instructions

1. Before commencing installation or maintenance, isolate the main

electrical supply for the appropriate circuit at the fuse board.

This product requires a 24V LED driver which is only

suitable for connecting to a 240V 50Hz supply.

3. The light should be mounted onto a secure surface.

4. Position lights where they will not be exposed to steam

or splashes etc.

5. Suitable for furniture lighting.

6. When the lamp expires the ﬁtting must be replaced.

7. Class III safety extra low voltage (SELV).

Waste Electrical & Electronic Equipment (WEEE)

The Symbol on the product, or on the document accompanying the product, the crossed out

wheelie bin symbol, indicated that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic waste.

Power DrillPZ1 Screw Bit10mm

Drill Bit

Pencil

Installation

Operation

Maintenance & Care

Once ﬁxed the SE9080HD light

is activated on the opening

of the cabinet door. The IR

sensor detects that the door

is no longer in its path and

activates the light.

HD LED In-CabInEt LIgHt

wItH IR SEnSoR

• Ensure that the power is disconnected prior to cleaning.

• To keep the ﬁnish of this product, wipe over with soft cloth periodically.

• Do not use harsh chemical solvents, it may dis-colour or damage the ﬁnish.

Finally wire the LED driver to 240V mains supply

or 13A plug top.

Re-attach the light unit to the bracket once

ﬁxed.

Taking the bracket, mark-up

the positions for the screw

holes in the cabinet.

Secure the bracket with

2 screws tightly to the inside

of the cabinet.

Unclip the bracket from the back of the

light ﬁtting.

Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY

www.sensio.co.uk

Technical drawings for illustration purposes only, Sensio has the right to change any information

without prior notice. Make sure you check all hole cut outs before work commences.

Plug the white connector into the 24V LED

driver distributor block. Beware not to exceed

the wattage of the LED driver, the max wattage

will be displayed on the 24V LED driver and on

the light unit ﬁtting it will display the wattage

requirement.

Drill hole in bottom of cabinet and feed

cable through.

Otros manuales de Equipo de iluminación de Sensio

Sensio

Sensio Strata Manual de usuario

Sensio

Sensio SE184720 Manual de usuario

Sensio

Sensio Verso SE16092N0 Manual de usuario

Sensio

Sensio Torino SE17232C0 Manual de usuario

Sensio

Sensio Polar IP65 Manual de usuario

Sensio

Sensio SE10755P0 Manual de usuario

Sensio

Sensio Adapt SE186790 Manual de usuario

Sensio

Sensio SE20099N0 Manual de usuario

Sensio

Sensio CONNEX SE100190 Manual de usuario

Sensio

Sensio Vector SE181700 Manual de usuario

Sensio

Sensio SE14092P0 Manual de usuario

Sensio

Sensio Expanse Pro SE14192P0 Manual de usuario

Sensio

Sensio Luce Manual de usuario

Sensio

Sensio Nexus TrioTone SE11090T0 Manual de usuario

Sensio

Sensio Verona SE13792N0 Manual de usuario

Sensio

Sensio Ark TrioTone SE11192T0 Manual de usuario

Sensio

Sensio Blaze SE182720 Manual de usuario

Sensio

Sensio Neutron SE10455C0 Manual de usuario

Sensio

Sensio Linia SE980320 Manual de usuario

Sensio

Sensio Fino SE981320 Manual de usuario

Sensio

Sensio SIGMA S-BEND FLEXIBLE STRIP Manual de usuario

Sensio

Sensio Glow SE19079C0 Manual de usuario

Sensio

Sensio Linia SE980120 Manual de usuario

Sensio

Sensio Stellar Pro Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario