Sensata ISOSLICE-7 Manual de usuario
Sensata Technologies 1 220808
ISOSLICE-7 User Manual
ISOSLICE-7
Digital Input Pulse Counting
or 2 Frequency Input Isoslice Unit
Whilst every effort has been taken to ensure the accuracy of this document, we
accept no responsibility for damage, injury, loss, or expense resulting from errors or
omissions, and reserve the right of amendment without notice.
This document may not be reproduced in any way without the prior written
permission of the company
AUG 2022
Sensata Technologies 2 220808
ISOSLICE-7
The ISOSLICE-7 unit has 1 digital input for counting pulses or 2 digital inputs used for
measuring frequency.
The selection is made using dip switch 1. See the section on input mode for further details.
In pulse counting mode (dip switch 1 off) the number of pulses is stored as a 32-bit
number, spread over 2 parameters read by the E100 or Z-Port.
Parameter
1 Pulse input 1 high 16-bits
2 Pulse input 1 low 16-bits
The cumulative pulse count is saved every 14 seconds, in case of power failure.
In frequency measuring mode (dip switch 1 on) the frequency read from the 2 digital inputs
can be scaled from one of four ranges : 0 to 10Hz, 100Hz, 1000Hz, 10000Hz. See the
section on calibration for further details.
Parameter
1 Scaled frequency of input 3
2 Scaled frequency of input 5
Digital Inputs Link Fitting
There are 3 different input types the unit can accept
Volt Free Contact
The digital input is an optoisolator that must be connected to the common to switch the
input “ON”.
The input links must be fitted in the higher positions like this:
Sensata Technologies 3 220808
+24V dc input or +5V dc TTL input
The digital input is an optoisolator that must be powered externally by a +24V dc or +5V dc
input on the Input terminal, with the corresponding Ground to the Common terminal, to
switch the input “ON”.
The input links must be fitted in the lower positions like this:
Channel Number
The channel number is set up using the 8-way dipswitch, switches 2 to 8.
If all switches are off, the channel number is 1 (invalid, indicated by the LED flashing red):
Address Switches Action
8 add 1
7 add 2
6 add 4
5 add 8
4 add 16
3 add 32
2 add 64
Switches Switches 1 = On, 0 = Off
Channel 2 3 4 5 6 7 8 Channel 2 3 4 5 6 7 8
1 0 0 0 0 0 0 0 9 0 0 0 1 0 0 0
2 0 0 0 0 0 0 1 10 0 0 0 1 0 0 1
3 0 0 0 0 0 1 0 11 0 0 0 1 0 1 0
4 0 0 0 0 0 1 1 12 0 0 0 1 0 1 1
5 0 0 0 0 1 0 0 13 0 0 0 1 1 0 0
6 0 0 0 0 1 0 1 14 0 0 0 1 1 0 1
7 0 0 0 0 1 1 0 15 0 0 0 1 1 1 0
8 0 0 0 0 1 1 1 16 0 0 0 1 1 1 1
Channel
Sensata Technologies 4 220808
Input mode
Switch 1 is used to select between pulse counting mode and frequency input mode.
Switch 1 Off : Pulse counting on input 1
Switch 1 On : Frequency inputs measured on inputs 3 and 5
In frequency measurement mode the unit can measure any frequency between 0 & 10kHz
scaled using 4 selectable frequency ranges (see Calibration section for more details)
The number of pulses is retained and saved by the ISOSLICE-7 unit, so in the event of
power failure, the count is not lost. The count is saved at a maximum rate of once every
13.4 seconds, to preserve the life of its non-volatile memory. Each time the total is saved,
the green led will switch off briefly.
Reset Pulse Count Total
The pulse count total can be reset. Hold the raise button on the front panel down for about
15 seconds, until the green LED switches off. Release the button and the pulse count will
have reset.
Connections
The digital input is wired like this:
Volt-Free Contact: +24/5V TTL Vdc Input
7.
8.
12. Common
5. Input 5 (frequency channel 2)
6.
11. Common
1. Input 1 (pulse counting only)
2.
9. Common
3. Input 3 (frequency channel 1)
4.
10. Common
Input
Common
Input
Common
+24Vdc or 5V TTL
Sensata Technologies 5 220808
Calibration of the input frequency range
The ISOSLICE-7 has an LED that shows which mode it is in.
Green run mode
Amber learn range for frequency channel 1 (input 3)
Red learn range for frequency channel 2 (input 5)
In run mode, the frequency ranges selected can be observed without the risk of changing
the calibration. Push and release the Lower button to see the range for frequency channel
1 (input 3). The LED will flash amber. Count the number of times it flashes.
1 flash = 0 to10 Hz
2 flashes = 0 to100 Hz
3 flashes = 0 to1000 Hz
4 flashes = 0 to10000 Hz
In run mode, push and release the Raise button to see the range for frequency channel 2
(input 5). The LED will flash red. Count the number of times it flashes.
Changing the input range for channel 1 (input 3)
In run mode, press the Lower button and hold it for 4 seconds, until the LED changes from
green to amber.
Release the Lower button.
Push and release the Raise button to increase the frequency range
or Push and release the Lower button to decrease the frequency range.
The LED will flash green 1 to 4 times after a button press, indicating the range selected.
When the required range has been selected, push both buttons at the same time and
release. The amber LED will extinguish for ¾ second then change to green, as the
selected range is saved and it returns to run mode. The range is retained over a power
cycle.
Changing the input range for channel 2 (input 5)
In run mode, press the Raise button and hold it for 4 seconds, until the LED changes from
green to red.
Release the Raise button.
Push and release the Raise button to increase the frequency range
or Push and release the Lower button to decrease the frequency range.
The LED will flash green 1 to 4 times after a button press, indicating the range selected.
When the required range has been selected, push both buttons at the same time and
release. The red LED will extinguish for ¾ second then change to green, as the selected
Sensata Technologies 6 220808
range is saved and it returns to run mode. The range is retained over a power cycle.
Otros manuales de Cambiar de Sensata
