Senect TMP-50-SC Manual de usuario

Temperature Sensor TMP

MANUAL

Product type

Name of product:

Sensor Temperature TMP

Type:

TMP-50-SC

Art.-No.:

2500

Producer:

SENECT GmbH & Co. KG

An 44 –No. 11

76829 Landau / Germany

Important note:

Please read this manual carefully and store it so that you can use

it later. Read the warning and safety notes attentive.

Further information and latest software releases or documents

can be downloaded from:

www.senect.de

Table of contents

Product type.................................................................................. 2

Table of contents........................................................................... 3

Used symbols and wording ........................................................... 4

General Security Notes.................................................................. 5

Intended use.................................................................................. 6

Getting started .............................................................................. 7

Getting started –Short version..................................................... 9

Maintenance and cleaning ............................................................ 9

Cleaning..................................................................................... 9

Recalibration ............................................................................. 9

Temperature: 2-Point-Calibration........................................... 10

Technical data ............................................................................. 12

Information about the correct disposal ...................................... 14

Guarantee.................................................................................... 14

Used symbols and wording

DANGER!

Warning of life threatening

dangers.

WARNING!

Warning of possible life

threatening and / or severe

irreversible injuries.

ATTENTION!

Warning of possible medium

or slight injury.

ATTENTION!

Follow the notes to avoid

damage of equipment.

NOTE!

Further information for the

use of the device.

NOTE!

Further information for the

use of the device.

General Security Notes

The Temperature Sensor TMP is an electronic sensor unit for

the measurement of the water temperature in aquaculture

applications and must be used in combination with SENECT

control units.

Since it is an electronic product the common prerequisites

for a safe instrument usage must be fulfilled. The

corresponding control unit must be operatated

with 230 V AC (~50 Hz). Ensure that all cables are

installed safely so that no obstacles for persons

are built and all. Mount all cables and electric

devices (especially the silicone coated electronic

part) protected against direct environmental

impacts like overheating by direct sunlight and

water. Even if the product are protected against spray water,

the product´s lifetime will be elongated, if it is mounted on a

protected place. The Temperature Sensor TMP uses 24 V DC

supply voltage which is therefore not of danger for persons.

For many applications a ground fault circuit interruper

(interrupting current <= 30 mA) is required by law. Inform

yourself about the valid legislation.

Intended use

The operating temperature of the device must be between

0°C and +50°C. It is not allowed to modify the sensor, to open

the housing or to insert anything into the housing.

The Temperature Sensor TMP is designed to be operated by

professional users. However, it can be operated by children

of the age of at least 8 years and persons with limited

physical, sensorial or cognitive ability, if they are supervised

and trained in the usage of the instrument, so that no

dangers or threats can result of the operation.

Please store this manual. We suggest the storage a copy of

the manual in the vicinity of the device.

Technical and optical changes of this manual are subject to

alterations.

Warning: Before starting any maintenance work,

unplug all electrical devices in the water.

Intended use

The Temperature Sensor TMP can be used to measure the

temperature of water in a range between 0°C and +50°C and

Getting started

a resolution of 0.1°C in professional aquaculture

applications.

Getting started

Scope of delivery

o1 x Temperature Sensor TMP

o1 x Manual

Note

Please check directly after delivery, that the

package is not destroyed or damaged or was

opened before. Please check also, that all parts as

listed above are included. If anything is missing or broken,

please contact us as soon as possible within 14 days.

Unfortunately, we cannot accept later information of

damage, which happened during the transport.

Installation and start-up

Choose a place for the electronic interface of the

TMP which is clean, dry and protected from direct

sunlight. Ensure that all cables are placed safely

and all regulations are fulfilled.

Mount the sensor submerged at the position where the TMP

will measure the temperature.

Getting started

The sensor can be installed freely swimming with a float, e.g.

when the water level changes or fixed mounted, e.g. with

clamps. For tanks or pipes, the sensor can also be mounted

with water tight cable glands.

Fig. 1: Mounting possibilities of the temperature sensor TMP.

Connect the blue marked plug of the sensor with a sensor

input port (also blue marked) of your control unit.

The SENECT control units recognize the sensor and start

automatically the measurements.

The Temperature Sensor TMP is factory calibrated and need

not to be recalibrated –under for aquaculture typical

environmental conditions –within the first two years of

operation.

Getting started –Short version

1. Mount the sensor submerged.

2. Mount the electronic interface at a protected

location.

3. Connect the sensor cable with a control unit (plug

„SENSOR“).

4. The control unit recognizes the sensor and starts the

measurements.

Maintenance and cleaning

Cleaning

The sensor should be cleaned regularly by wiping with a soft

water-dipped paper towel or a cotton swab without cleaning

agents.

Do not steam-sterilize the sensor.

Recalibration

The recalibration is recommended for typical applications

every 2 years. In some applications, e.g. under harsh

environmental conditions, the sensor must be recalibrated

more frequently to guarantee precise measurements.

Maintenance and cleaning

Temperature: 2-Point-Calibration

To calibrate the temperature signal, two calibration points

are necessary. The calibration point 1 must have a lower

temperature (e.g. 0°C) than calibration point 2. This

temperature (point 1) must be lower than 20°C.

The calibration point 2 (higher temperature) must be

between 30°C and 50°C.

Submerge the sensor in a water bath with the lower

temperature (calibration point 1) and wait, until the sensor

has the same temperature as the water. Select in the menu

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

Omron

Omron E5EX-H Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado