Seltron ZCE6 Basic Manual de usuario
Zone heating / cooling controller
ZCE6 Basic and ZCE6 Advance
EN Instructions for use and setup
2 English
INTRODUCTION
ZCE6 controllers have been designed for the control of zone heating and/or
cooling. The control is carried out using thermal actuators on the distributor valves
based on the temperatures obtained from room units. There are six independent
temperature zones with the possibility of controlling fourteen heating-cooling
units in total. The ZCE6 Advance controllers also enable the control of the energy
source, mixing valve and circulation pump. The controller allows wired or wireless
connection of room units. The 24V thermal actuators can be used with additional
24V power supply. More controllers can be connected together when more tem-
perature zones or units are needed.
English 3
1-Connection terminals for controller power supply (230V~).
2-Connection terminals for circulation pump, energy source and mixing valve
control. *
3-Connection terminals for the control of 24V~ thermal actuators.**
4-Selector switch for the control voltage of thermal actuators. **
5-LED lights for the signalisation of operation.
6-Connection terminals for the control of thermal actuators.
7-Connection terminals for connecting wired room units.
8-Connection terminals for connecting temperature sensors and digital inputs.
9-Connection terminals for the BUS connection of controllers.
10-Spare electrical fuse.
11-Electrical fuse.
12-Conrmation key .
13-Selection key .
14-Connection terminals for the antenna for wireless room units.
15-AUX connection terminals.
*Only with ZCE6 Advance.
**Connection terminals and the switch are located under a protective cover.
APPEARANCE OF THE CONTROLLER
1
10
2 3 4 5 67 8 9
11 12 13 14 15
4 English
Signalisation of temperature zone operation.
When the LED light is on, the thermal actuators connected to
the zone are in the open state, and vice versa.
SIGNALISATION OF OPERATION
Signalisation of circulation pump output operation. When the
LED light is on, the output is active. *
Signalisation of energy source output operation. When the
LED light is on, the output is active. *
Signalisation of mixing valve output operation. When the LED+
light is on, the mixing valve opens, when the LED- light is on,
the mixing valve closes. *
Signalization of the leading (Master) controller in BUS con-
nection. When the LED light is on, the controller in the BUS
connection is the leading one (Master), and when the LED
light ashes, the controller is the subordinate one (Slave).
Signalisation of pairing process. When the LED light ashes,
the controller is in the pairing phase.
Signalisation of the controller status. When the LED light is on,
the controller is in normal operation, when the LED light is o,
the menu page is displayed.
*Only with ZCE6 Advance.
English 5
MENU
In the menu, we carry out basic settings of the controller. We move from the home
screen to the menu by holding the key for 2 seconds; we move between
individual groups in menu by pressing the key.
6 English
MENU – HYDRAULIC SCHEME
The ZCE6 Advance controller has three hydraulic schemes to choose from, the
ZCE6 Basic only 1 scheme. Hydraulic schemes are shown in chapter »Hydraulic
schemes«.
Example: Shift from scheme 1 to scheme 3.
English 7
MENU – PAIRING OF ROOM UNITS
With the pairing process, we connect the RCD room unit with the controller and at
the same time assign zones to it.
Example: Pairing the RCD room unit with zone 1 and 2.
8 English
MENU – MASTER CONTROLLER
If more controllers are connected to the BUS connection, one controller must be
set as the leading (Master) controller.
Example: Setting the master controller.
English 9
MENU – PAIRING OF THE CONTROLLERS (MASTER CONTROLLER)
When more controllers are interconnected in the BUS connection, the controllers
must be connected – paired.
Example: Activation of the pairing process on the master controller.
10 English
MENU – PAIRING OF CONTROLLERS (SLAVE CONTROLLER)
After activating the pairing process on the master controller, pairing on slave con-
trollers must also be activated.
Example: Activation of the pairing process on the rst slave controller.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Seltron
Seltron
Seltron WXD10B Manual de usuario
Seltron
Seltron KXD10B Manual de usuario
Seltron
Seltron SGC36 Manual de usuario
Seltron
Seltron SCC40 Manual de usuario
Seltron
Seltron ACD20 Manual de usuario
Seltron
Seltron SGC26 Manual de usuario
Seltron
Seltron AHC40 Manual de usuario
Seltron
Seltron Regulus RCD2 Manual
