Sekonic i-346 Manual de usuario
Operating Manual
www. .com information@itm.com1.800.561.8187
2
Safety Precautions…………………………………………………… 1
1. Parts Designations ……………………………………………… 3
2. Explanation of LCD Screen Information …………………… 4
3. Before Using ……………………………………………………… 5
3-1. Inserting the Battery ………………………………………… 5
3-2 Power ON/OFF ……………………………………………… 5
3-3. Checking the Battery Capacity …………………………… 6
3-4. Replacing Battery during Measurement ………………… 6
3-5. Automatic Power OFF Function …………………………… 7
4. Basic Operation …………………………………………………… 8
4-1. Basic Operation Flowchart and Setting
the Measuring Mode …………… 8
5. Measurement …………………………………………………… 9
5-1. Continuous Measuring Mode ……………………………… 9
5-2. Single Measuring Mode …………………………………… 9
5-3. Timer Measuring Mode ………………………………… 10
6. Other Setting …………………………………………………… 11
7. Specifications…………………………………………………… 12
■Table of Contents
www. .com information@itm.com1.800.561.8187
1
Before using this product, please read this "Safety Precautions" for
proper operation.
The warning symbol indicates the possibility of death of
serious injury if the product is not used properly.
The caution symbol indicates the possibility of minor to
moderate personal injury or product damage if the product is
not used properly.
The note symbol indicates cautions or restrictions when using
the product. Please read all notes to avoid errors in operation.
The reference symbol indicates additional information
about the controls or related functions. Reading these is
recommended.
●Do not place batteries in open flame, attempt to short them,
disassemble them, apply heat to them, or recharge them
(except rechargeable batteries). They may burst and cause
fire, serious injury, or damage to the environment.
●Do not handle this product with wet hands, or leave it in the
rain or in a location where it may be splashed with water or
come into contact with moisture. This may result in damage
to the product.
●Do not attempt to disassemble the product for modification or
parts replacement.
■Safety Precautions
www. .com information@itm.com1.800.561.8187
2
■Safety Precautions
●Be sure not to drop the meter or subject it to sudden impact,
as the meter will be damaged,
●Do not store the meter in areas of high temperature or high
humidity, as the meter will be damaged.
●Be careful of condensation caused by sudden changes
in temperature. It will cause damage or malfunction of the
meter.
●If the temperature goes below -10°C, the response of the
liquid crystal display will slow down greatly and the display
will become difficult to read. Between 0~10°C, the liquid
crystal display response will slow down somewhat but the
meter will not be harmed.Also, if the temperature exceeds 50
°C, the liquid crystal display will darken and become difficult
to read, but when it return to room temperature it will return
to its normal condition.
●If the meter is left in direct sunlight or near a heater, the
temperature of unit’s surface will rise and may result in
damage. Please be careful when using the meter in these
types of locations.
●If the meter will not be used for an extended period of time,
it is recommended to remove the batteries to avoid possible
damage caused by battery leaking.
Maintenance Notes
● Be careful not to allow the light receptor to become dusty,
dirty or scratched as this may affect the accuracy of the
reading.
● Do not use organic solvents such as benzene or paint
thinner to clean the surface of the light receptor.
www. .com information@itm.com1.800.561.8187
3
1. Parts Designations
②Light Receptor
③Mode Button
④Measuring Button
⑤LCD Screen
⑥Up Button
⑦Down Button
⑧Timer
Button
⑨Battery Cover
①Power Button
www. .com information@itm.com1.800.561.8187
4
Display of the i-346 *This diagram is for explanation purpose.
①Battery Capacity Indicator (See page 6)
②Measuring Mode Display
Displayed at the continuous measuring mode. (See page 9)
Displayed at the single measuring mode. (See page 9)
Displayed at the custom setting mode. (See page 11)
③Illumination Value/ Timer Display
Measured illuminance is displayed.
Display example
Set timer second is displayed. (See page 10)
Display example
2. Explanation of LCD Screen Information
www. .com information@itm.com1.800.561.8187
5
3. Before Using
⑨Battery
Cover
3-1. Inserting the Battery
1) Requires type-AA 1.5-volt battery.
2) Slide the battery cover in the
direction of the arrow to remove.
Slide down Battery Cover ⑨in the
direction of the allow to move.
3) Insert the battery observing the
polarity with the +, -marks in the
battery compartment.
4) Align Battery Cover ⑨with main
unit and slide shut.
Make sure that the cover is properly
in place and closed.
●Do not place batteries in open flame, attempt to short them,
disassemble them, apply heat to them, or recharge them
(except rechargeable batteries). They may burst and cause
fires, serious injury, or damage to the environment.
●Please insert the battery minus "-" side first. When removing
the battery, remove it plus ”+” side first.
●If the meter will not be used for an extended period of time,
it is recommended to remove the battery to avoid possible
damage caused by battery leaking.
3-2. Power ON/OFF
Power ON : Press the Power Button ①.
Power OFF : Press and hold the Power Button ①for 1 second or
longer and the meter will turn off.
● A three second pause between power ON and OFF is
recommended to avoid damage to the meter.
● If the LCD does not light, check that the battery capacity is
sufficient, and check that the battery positive and negative
terminals are not reversed.
www. .com information@itm.com1.800.561.8187
6
3-3 Checking the Battery Capacity
When the Power Button ①is ON, the battery power indicator
on the LCD Screen ⑤is displayed.
(Displayed) Sufficient battery power remaining.
(Displayed) Low battery power remaining. Have a spare battery ready.
(Blinking) When the indicator blinks, replace the battery immediately.
●The LCD screen will appear and immediately switch off, when
the battery power is very low. The battery should be replaced
immediately. Having a spare battery is recommended.
●A fresh battery is capable of continuous readings of;
Manganese 10 hours
Alkaline 20 hours (based on Sekonic measuring.)
3-4Replacing Battery during Measurement
1) Always turn the power OFF before replacing battery. If
battery is removed with the power ON, the setting can no
longer be recalled.
2) If an unexpected display, i.e. settings other than selected,
appears on the LCD after battery replacement or while
operating the meter, or the meter does not respond when
a button is pressed, remove the battery, wait at least 10
seconds, and then re-install them.
3. Before Using
www. .com information@itm.com1.800.561.8187
7
3. Before Using
3-5 Automatic Power OFF Function
To save battery capacity, the meter will be automatically turned
off about 4 minutes after the last button is pressed.
● Even if automatic power off function works or the power is
turned off by pressing the Power Button ①, the setting of
timer is memorized.
● Automatic power OFF function is not available while
continuous measuring mode.
● If the Power Button ①is pressed and held when the power is
off, the meter will turn ON for about 1 minute, and then turn
OFF automatically.
(Battery capacity can be saved even if the Power button is
pressed during transport.)
www. .com information@itm.com1.800.561.8187
8
4-1. Basic Operation Flowchart and Setting the Measuring Mode
1) To enter the Custom Setting to select either Lux or FC, hold
the Mode Button ③and press the Power Button ①.
2) Select the measurement mode by pressing the Mode Button
③or Timer Button ⑧. Measuring modes are switched
according to the chart below.
Continuous
Measuring Mode
Timer Measuring
Mode
Custom Setting
Single
Measuring Mode
Hold Mode Button ③and press
Power Button ①to enter
4. Basic Operation
M
O
D
E
TIMER
④Measuring
Button
⑧Timer Button
①Power
Button
Power ON
Timer Button ⑧to select
(See page 9)
(See page 9)
(See page 10)
(See page 11)
Mode Button ③to select
③Mode
Button
www. .com information@itm.com1.800.561.8187
Tabla de contenidos
Otros manuales de Instrumento de medición de Sekonic
Sekonic
Sekonic SPECTROMASTER C-800 Guía del usuario
Sekonic
Sekonic DIGI LITE F L-328 Manual de usuario
Sekonic
Sekonic SPECTROMASTER C-7000 Guía del usuario
Sekonic
Sekonic LITEMASTER PRO L-478 Series Guía del usuario
Sekonic
Sekonic SPEEDMASTER L-858D Manual de usuario
Sekonic
Sekonic DigitalMaster L-758 Cine Manual de usuario
Sekonic
Sekonic Flashmate L-308S Manual de usuario
Sekonic
Sekonic AUTO LEADER L-188 Manual de usuario
Sekonic
Sekonic MULTIMASTER L-408 Manual de usuario
Sekonic
Sekonic SPECTROMASTER C-800 Manual de usuario
Sekonic
Sekonic FLASHMATE L-308X Manual de usuario
Sekonic
Sekonic C-500R Manual de usuario
Sekonic
Sekonic SPECTROMASTER C-7000 Guía del usuario
Sekonic
Sekonic DIGITALMASTER L-758DR Manual de usuario
Sekonic
Sekonic C-500 Manual de usuario
Sekonic
Sekonic Litemaster Pro L-478DR Manual de usuario
Sekonic
Sekonic L-608 CINE Manual de usuario
Sekonic
Sekonic LITEMASTER PRO L-478DR-U-PX Manual de usuario
Sekonic
Sekonic FLASH MASTER L-358 Manual de usuario
Sekonic
Sekonic L-508 CINE ZOOM MASTER Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario