Seiko Epson S5U1C17702T1100 Manual de usuario
CMOS 16-BIT SINGLE CHIP MICROCOMPUTER
(Software Evaluation Tool for S1C17702)
S5U1C17702T1100
Hardware Manual
Evaluation board/kit and Development tool important notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,
or development purposes only. Do not use it for other purpose. It is not intended to meet the requirement of
design for finished product.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is not the
product for consumer. The user should use this goods properly and safely. Seiko Epson dose not assume any
responsibility and liability of any kind of damage and/or fire coursed by usage of it. User should cease to use
it when any abnormal issue occurs even during proper and safe use.
3. The part used for this evaluation board/kit or development tool is changed without any notice.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written
permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material
or due to its application or use in any product or circuit and, further, there is no representation that this material is
applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any
intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that
anything made in accordance with this material will be free from any patent or copyright infringement of a third
party. When exporting the products or technology described in this material, you should comply with the
applicable export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical
information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other
military purposes.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective
companies.
©SEIKO EPSON CORPORATION 2012, All rights reserved.
Devices
S1 C 17xxx F 00E1
Packing specifications
00 : Besides tape & reel
0A : TCP BL 2 directions
0B : Tape & reel BACK
0C : TCP BR 2 directions
0D : TCP BT 2 directions
0E : TCP BD 2 directions
0F : Tape & reel FRONT
0G : TCP BT 4 directions
0H : TCP BD 4 directions
0J : TCP SL 2 directions
0K : TCP SR 2 directions
0L : Tape & reel LEFT
0M : TCP ST 2 directions
0N : TCP SD 2 directions
0P : TCP ST 4 directions
0Q : TCP SD 4 directions
0R : Tape & reel RIGHT
99 : Specs not fixed
Specification
Package
D: die form; F: QFP, B: BGA
Model number
Model name
C: microcomputer, digital products
Product classification
S1: semiconductor
Development tools
S5U1 C 17000 H2 1
Packing specifications
00: standard packing
Version
1: Version 1
Tool type
Hx : ICE
Dx : Evaluation board
Ex : ROM emulation board
Mx : Emulation memory for external ROM
Tx : A socket for mounting
Cx : Compiler package
Sx : Middleware package
Corresponding model number
17xxx: for S1C17xxx
Tool classification
C: microcomputer use
Product classification
S5U1: development tool for semiconductor products
00
00
Configuration of product number
Table of Contents
S5U1C17702T1100 HARDWARE MANUAL EPSON i
(SOFTWARE EVALUATION TOOL FOR S1C17702)
- Table of Contents -
1 Features .......................................................................................................................... 1
2 Components Included in the Package
......................................................................... 2
3 Name and Functions of Each Part ............................................................................... 3
3.1 Name of Each Part ............................................................................................................ 3
3.2 Dimensions of the Boards ................................................................................................. 4
3.2.1 Dimensions of the CPU Board ............................................................................ 4
3.2.2 Dimensions of the ICD Board ............................................................................. 5
3.2.3 Dimensions of the LCD Panel Board .................................................................. 6
3.3 Main Parts ......................................................................................................................... 8
3.4 Functional Description of Each Part .................................................................................. 9
3.4.1 ICD board ........................................................................................................... 9
3.4.2 CPU board .......................................................................................................... 9
4 Block Diagrams ............................................................................................................ 10
5 Operating Environment and Start-Up Procedures .................................................... 11
5.1 Simple Software Development Environments .................................................................. 11
5.2 Standalone Operation of SVT17702 ................................................................................ 14
5.3 ICD Board Firmware Update Procedures ........................................................................ 14
6 Differences between ICD Board and ICD Mini ........................................................... 15
7 I/O Ports ......................................................................................................................... 16
8 Setting Switches
........................................................................................................... 17
8.1 Setting for SW6 ................................................................................................................ 17
8.2 Setting for SW8 ................................................................................................................ 18
8.3 Setting for SW9 ................................................................................................................ 18
9 Key Input Circuit on the CPU Board ........................................................................... 19
10 Infrared Emitting Diode/Receiver Module ................................................................ 20
10.1 Emitting and Receiving Light at Infrared Area ................................................................ 21
10.2 Power Supply Switch for Infrared Transmitter Module ................................................... 21
11 LCD Panel .................................................................................................................... 22
11.1 Segments and Commons of the LCD Panel ................................................................... 22
12 Serial Ports .................................................................................................................. 23
13 External Input for OSC3 ............................................................................................. 24
14 Expansion Interface ................................................................................................... 25
14.1 JICD Connector .............................................................................................................. 26
14.2 JEX Connector ............................................................................................................... 27
14.3 JEX2 Connector ............................................................................................................ 28
14.4 JRIF Connector .............................................................................................................. 29
14.5 Switching the SPI Port Connector .................................................................................. 30
Appendix A How to Measure Current Consumption ........................................................31
1 Features
S5U1C17702T1100 HARDWARE MANUAL EPSON 1
(SOFTWARE EVALUATION TOOL FOR S1C17702)
1 Features
S5U1C17702T1100 (Software evaluation Tool for S1C17801. Hereafter referred to as SVT17702)is an evaluation
board for S1C17702 manufactured by SEIKO EPSON.
The SVT17702 consists of two circuit boards: CPU and LCD boards. By connecting these boards, the SVT17702
allows the user to debug the application software without an ICD or other debugging tools.
In addition, it provides extended interfaces such as serial ports, allowing you to connect your own expansion boards
to the SVT17702.
<CPU Board>
CPU S1C17702
Input power voltage +3.3 VDC (supplied through the ICD interface or CR2032 coin cell battery)
CPU input clock OSC1: 32.768 kHz
OSC3: 6 MHz
On-board functions/devices ・Reset switch
・Expansion interface connectors (GPIO, UART, I2C and SPI)
・ICD board connector
・Key input circuit (4 keys)
・Rotary encoder with switch
・Infrared transmitter LED/Receiver module
・ STN LCD panel (display size: 32 commons x 128 segments, black &
white)(32 commons and 72 segments can be driven)
<ICD Board>
PC interface USB 1.1
Power supply voltage USB bus power (On-board regulator output voltage of 3.3 V)
On-board functions/devices ・Tri-color status LED
・Reset switch
・CPU board connector
2 Components Included in the Package
2 EPSON S5U1C17702T1100 HARDWARE MANUAL
(SOFTWARE EVALUATION TOOL FOR S1C17702)
2 Components Included in the Package
The S5U1C17702T1100 package contains:
(1) SVT17702 CPU board (evaluation board) .................... 1
(2) SVT17702 ICD board ................................................... 1
(3) USB cable .....................................................................1
(4) Coin cell battery (CR2032/3V) .....................................1
(5) Warranty Registration Card ...........................................1 each for English/Japanese
(6) Warranty Card ............................................................... 1 each for English/Japanese
(7) Precautions in Use .........................................................1 each for English/Japanese
(8) Manual Download Guide ..............................................1 each for English/Japanese
3 Name and Functions of Each Part
S5U1C17702T1100 HARDWARE MANUAL EPSON 3
(SOFTWARE EVALUATION TOOL FOR S1C17702)
3 Name and Functions of Each Part
3.1 Name of Each Part
The following describes name and functions of each part:
Figure 3.1.1 Parts Mounted on the Front Side of the Board
(1) LED(RGB) (6) Rotary encoder (11) CPU board reset switch
(2) SW4(7) SW2(12) Expansion board connector (JEX2)
(3) Crystal oscillator (6MHz/32kHz) (8) SW1(13) Expansion board connector (JEX)
(4) SW3(9) Infrared receiver module (14) ICD board reset switch (SW1)
(5) S1C17702 (10) Infrared transmitter module (15) miniB USB connector
Figure 3.1.2 Parts Mounted on the Back Side of the Board
(1) Rotary encoder
(2) ICD board to CPU board connector (JICD)
(3) Battery socket
(4) Expansion board connector (JRIF) (Not mounted)
CPU boardICD board
(1) (2) (4)
(3)
(5) (6) (7) (8)
(13)
(12)(9)
(10)
(11)
(14)
(15)
Dot matrix STN LCD panel
CPU board ICD board
(1)
(4) (3) (2)
3 Name and Functions of Each Part
4 EPSON S5U1C17702T1100 HARDWARE MANUAL
(SOFTWARE EVALUATION TOOL FOR S1C17702)
3.2 Dimensions of the Boards
3.2.1 Dimensions of the CPU Board
The following drawings show the dimensions of the CPU board.
<Top view>
101.5
130
140
80
0.5
18 18 12
79
1
4
52.5
136
2.77
7.85
30.77
28 2.3
2.3
5.5
23
43
14.5
21.5
29.5
37.5
3.1
CPU
JEX2
SW3 SW2 SW1
SW5
AN333
GP6UX311QS
SW4
1
14
2 1
160
212 1
1
2
2
JMINI
LCD
80
81
4.5
19
19
20
20
1
1
2
2
1
4-R2
Vcc
GND
VOUT
JEX
6-φ7
6-φ3.3 hole
Figure 3.2.1.1 Dimensions of the CPU Board (Front)
<Bottom view>
91
70
40
5.2
15
30 30
70
130.61
22.5
15 7
2-φ1.2 hole
4.55
1.3
4.5 0.8
10
10
33.9
21.5
21.5
land
10
2 1
9
JICD V1
SW6
SW7
B C S A 19 20
21
JRIF
13 +3
2
−
Figure 3.2.1.2 Dimensions of the CPU Board
∗ Precautions
• All dimensions are in millimeters (mm).
• Board thickness: 1.6 mm.
3 Name and Functions of Each Part
S5U1C17702T1100 HARDWARE MANUAL EPSON 5
(SOFTWARE EVALUATION TOOL FOR S1C17702)
3.2.2 Dimensions of the ICD Board
The following drawings show the dimensions of the ICD board.
<Top view>
4
21.5
37.5
43
50
4-φ3.5 through hole
4-R2
44-φ7 land
5.5
9
JUSB
15
Figure 3.2.2.1 Dimensions of the ICD Board (Front)
<Bottom view>
4.95
JICD
1
2
9
10
Figure 3.2.2.2 Dimensions of the ICD Board (Back)
∗ Precautions
• All dimensions are in millimeters (mm).
• Material: FR4, Board thickness: 1.6 mm
3 Name and Functions of Each Part
6 EPSON S5U1C17702T1100 HARDWARE MANUAL
(SOFTWARE EVALUATION TOOL FOR S1C17702)
3.2.3 Dimensions of the LCD Panel Board
The following drawings show the dimensions of the LCD panel OPTO0569NG manufactured by Casil Optoelec-
tronic Product Development Ltd.) that is to be mounted on the LCD board.
(Excerpts from the Specifications of Casilʼs OPTO0569NG)
29.5±0.1
2–1.0
2.5
5.0
2.5
30.0±0.1 30.0±0.1
9.5±0.1
7.0±0.1
4.0
0.6
83.15(V.A.)
128 x 32 DOTS
86±0.2
88.4±0.2
34.5±0.2
32.1±0.2
20.75(V.A.)
ELASTOMER
(ZEBRA CONNECTOR)
Figure 3.2.3.1 LCD Panel Dimensions of LCD, Bezel and Zebra (Elastomer Connector)
Tabla de contenidos
Otros manuales de Hardware de computadora de Seiko Epson
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
