Secure SCS317 Manual de usuario

SCS317

User Instructions

SCS317 7 Day Wireless Programmable

Room Thermostat

Programmable room thermostats are widely recognised as one

of the best ways in which to control central heating. The SCS317

programmable room thermostat has a large display and intuitive

user interface, making it easy to set up and use. SCS317 uses a

sophisticated time proportional integral (TPI) algorithm for

accurate temperature control and energy efficiency.

Actual Room

Temperature

Day of

Week

Time of

Day

Until (Time)

Then (Temp)

Enter

Button

+ Button- ButtonBack

Button

Set

Temperature

DISPLAY

SCS317

DISPLAY

Actual Room Temperature This is the actual room temperature

measured by the SCS317

Set Temperature This is the temperature that the SCS317

will allow the room to reach. The

temperature range can be set between

5°C and 30°C

When the temperature shown in the

display is achieved the SCS317 will

switch the heating OFF.

If the temperature in the room falls below

the setting the SCS317 will switch the

heating ON.

Until (time) This is the time that the next

temperature setting is due to operate

Then (temp) This is the temperature setting that is

due to operate next

Day of the week It is important that the correct day of the

week shows in the display

Time of day This is the current time of day

Setting Buttons Press any button to illuminate the

display.

The message 'To override press -/+ To

see menu press ENTER' will appear

No Radio waves Wireless connection not set up

Solid Radio Antenna Z-Wave communication present

– Flashing Radio Antenna – Temporary

loss of Z-Wave communication

ACTIVATING THE BACK-LIT DISPLAY

Press any button to illuminate the display. This will remain illuminated for

10 seconds

GENERAL INFORMATION

During programming please note that the display will return to its normal

operating screen if the last button press exceeds 10 seconds. 3

TEMPORARY OVERRIDE

A temporary temperature change can be made at any time. It is

also possible to extend how long this temperature override is in

operation.

The temperature will revert to its normal programmed setting at

the next timed temperature change

TEMPORARY OVERRIDE WITH TIME EXTENSION

(Maximum of 4 hours)

The temperature will revert to its normal programmed setting

at the next timed temperature change.

Press ‘-’ or ‘+’ to

adjust temperature

New temperature

setting will be shown

on the display

Press ‘-’ or ‘+’ to

adjust temperature

New temperature

setting will be

shown on the

display

Press ENTER

Press ‘+’ to

adjust the time

Press ENTER The hours of

the UNTIL time

will flash

PERMANENT OVERRIDE

In the 'HOLD' position the temperature can be overridden by

pressing either the '-' or '+' buttons. This will then become the

new 'HOLD' temperature

PERMANENT OVERRIDE – CANCELLATION

Press ‘-’ or ‘+’ to

adjust temperature

New temperature

setting will be

shown on the

display

Press ENTER

The hours of

the UNTIL time

will flash

Press ENTER

Press the '+'

repeatedly until

HOLD appears in

the display

Message will

appear briefly

confirming

'Temperature set

until manual

release'

Press BACK Press ENTER

SETTING UP THE SCS317

Upon initial installation the SCS317 has the following factory

default settings

Settings – Monday to Friday

Time Target Temperature

Period 1 06:00 am 20 °C

Period 2 08:30 am 18 °C

Period 3 11:30 am 20 °C

Period 4 01:30 pm 18 °C

Period 5 05:00 pm 21 °C

Period 6 10:00 pm 15 °C

Settings – Saturday and Sunday

Time Target Temperature

Period 1 07:00 am 20 °C

Period 2 10:00 am 19 °C

Period 3 11:30 am 21 °C

Period 4 01:30 pm 18 °C

Period 5 05:00 pm 21 °C

Period 6 11:00 pm 15 °C

These can be changed by the installer or the end user at any

time by accessing the MAIN MENU

MAIN MENU

To access the MAIN MENU take the following steps:

MENU OPTIONS

Press ENTER twice Press '-' or '+' to

toggle between the

menu options

Programme This allows the user to adjust the different

time and temperature settings from the

factory default settings shown in the table on

page 6.

Up to six different temperature levels can be

set in any 24 hour period

Standby This puts the SCS317 into Frost protection or

Standby condition and allows the heating to

be permanently switched off but will activate

and switch the heating on if the temperature

in the house falls below the standby

temperature set.

All programme settings are overridden and

the unit will not return to normal operation

until the standby period has ended by

pressing the ENTER button.

Holiday This puts the SCS317 into a temporary

standby mode with a start and end date

which can be set to coincide with a holiday

period. At the end of the set period the

SCS317 will resume normal operation

Time / Date The SCS317 has a built in clock and

calendar. This will require setting on initial

installation. If this has not been set on

installation please go to Setting the TIME and

DATE section on page 12 before continuing

Set Up Enables the programming of various options

outlined in the SET UP MENU on page 13 of

these instructions – These should be set on

installation.

Setting the PROGRAMME

Six time and temperature settings are available in each 24 hour period.

Pressing BACK at any time in this process will return you to normal

operating mode.

If only two different temperature settings are required in 24 hours then set

the first time and temperature using programme one (P1) and the second

time and temperature setting using programme setting two (P2). The

remaining programmes (P3 to P6) should all be set to the same time and

temperature as P2.

This same method can be used if three, four or five temperature levels are

required, always using the first settings to provide the temperature change

commands with the remaining settings that are not required set to the same

time and temperature as the last required setting.

Press ENTER three

times

The day of the week

will flash

Press '-' or '+'

to select day to

programme

Press ENTER

Time / Temperature

setting P1 will flash

Press '-' or '+' to

select time /

temperature period

you wish to set (P1

to P6)

Temperature will

flash, use the '-' or

'+' to select the

required

temperature

Press ENTER

The hours START

time will flash

Press '-' or '+' to

adjust the hours

then press ENTER.

The minutes will

then flash.

Press '-' or '+' to

adjust the minutes

then press ENTER.

If you require to set further periods for

the same day, the next period will now

automatically flash. Follow this process

again to programme as required

On completion of period 6

(P6) go to the copy

process on Page 9 of this

booklet

To copy the same programmes to other days of the week,

please follow the process below

Setting the STANDBY

To exit STANDBY mode, press ENTER TWICE

When you have set

P6 the message 'To

Copy press ENTER'

will appear.

Press '-' or '+' to select the

days you wish to copy the

set programmes. Pressing

ENTER after each day to

confirm

The next

sequential day

will now flash.

When complete press BACK

to return to normal operating

mode

Press ENTER

To programme remaining

days please go to the start of

the process 'Setting the

PROGRAMME'

Press ENTER Twice

The words STANDBY and

Standby Enabled will appear

on the display

Press ENTER

After a short period Standby

Enabled will disappear from

the display

Press '-' or '+' until

STANDBY

appears on the

display

Setting the HOLIDAY programme

Pressing BACK at any time in this process will return you to

normal operating mode

Press ENTER twice

The START date

will now flash

Press ENTER

Press the '-' or '+' to

adjust to the date you

wish the holiday

programme to start.

Pressing ENTER to

change between Day,

Month and Year

Press '-' or '+' until

HOLIDAY appears

on the display

The BACK date

will now flash

Again, Press the '-' or '+' to

adjust to the date you wish

the holiday programme to

end. Pressing ENTER to

change between Day,

Month and Year

HOLIDAY

programme is now

set

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Secure

Secure

Secure SCP318 Instrucciones de operación

Secure

Secure HRT4-B Instrucciones de funcionamiento

Secure

Secure ThermoPlus AS1 Instrucciones de operación

Secure

Secure SCT007 Instrucciones de operación

Secure

Secure SRT322 Instrucciones de funcionamiento

Secure

Secure SEC_SRT321 Manual de instrucciones

Secure

Secure SRT321 Instrucciones de funcionamiento

Secure

Secure H3747 Manual de usuario

Secure

Secure Beanbag Manual de usuario

Secure

Secure radbot 1 Manual de usuario

Secure

Secure C1727 Manual de usuario

Secure

Secure SRT323 Instrucciones de funcionamiento

Secure

Secure SRT321 Manual de usuario

Secure

Secure C1727 Manual de usuario

Secure

Secure SCS311 Manual de usuario

Secure

Secure SCT007 Manual de usuario

Secure

Secure STP328 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario