Sector Alarm TC Manual de usuario
User Manual
Home Alarm system: Sector Alarm TC
Welcome to Sector Alarm
This user manual will provide you with support in the daily use of
your system. We recommend that you read the manual in order to
fully understand how your alarm works.
We hope that this alarm will assist you over
many years, keeping you safer on a daily basis.
Over the first few pages, you will find a brief
description about how your alarm works.
You can get in touch with our customer service
team at any time if you have any questions.
Tel: 0207 345 000
Always activate your alarm!
Asiakaspalvelu
Sector Alarm Oy
Esterinportti 2
00240 HELSINKI
Tel: (+358) 207 345 000
(Price 8,8 snt/min)
asiakaspalvelu@sectoralarm.fi
www.sectoralarm.fi
2 SECTOR ALARM
Customer number Installation number
Easy-to-use alarm system
The following will give you information about the most important
functions of your alarm.
Activate Full Arm mode (activate the entire alarm system)
Press the button Activating Full Arm mode on the keypad or on the remote
control.
Activate Part Arm mode (activates part of the alarm system*)
Press the button Activating Part Arm mode on the keypad or on the remote
control.
Deactivate the alarm system:
Enter your personal code or place the keytag over the keytag reader symbol on the
keypad
or press the Deactivation button on the remote control.
*Part Arm mode is programmed according to your needs. The Sector Alarm Security Advisor will
program the alarm according to your preferences.
EASY-TO-USE ALARM SYSTEM 3
Content
Images from the camera detector 5
How to use the keypad 6
Signal lights on the keypad 7
How to use the alarm system 8–11
Activating using the keypad 8
Activating using the remote control 9
Deactivating using the keypad 10
Deactivating using the remote control 10
Siren and sound 10
Door signal on/o 11
Maintenance and advice 15
4 CONTENTS
Panic alarm function 11
Information about the most common alarm components 12–13
Smart solutions 14
Images from the camera detector
The following clause defines how images should be processed when
transferred within systems equipped with one or more detectors with
cameras installed.
• Images will only be transferred to our Alarm Receiving Centre in the event of an alarm
activation.
• Images are processed in accordance with the regulatory requirements and the Sector
Alar Privacy Policy.
• The images will be used solely as aids in the management of alarm activation. In other
words, in order to evaluate and determine the cause of an activation.
• Only the Alarm Operators, and if needed Police authorities, will have access to the
images received.
IMAGE PROCESSING CLAUSE 5
How to use the keypad
The keypad is used to activate or deactivate the alarm system by
means of a personal code or keytag. The keypad is equipped with
a keytag reader at the bottom-centre.
Signal light 1
Alarm triggered
Signal light 2
System error
Keytag reader
SOS Panic
Alarm function
Activating
Full Arm mode
Activating
Part Arm mode
6 HOW TO USE THE KEYPAD
Signal light 3
Tamper alarm
Signal lights on the keypad
There are three signal lights on the front of the keypad. These
indicate the current status of the alarm system.
Signal light 1 – alarm triggered
On: The alarm system has been triggered or one of the detectors is unable to be
activated. This could be because a door or window protected with a magnetic sensor
is open.
Flashing: There is an alarm in the alarm system’s memory which needs to be reset.
O: The alarm system is ready to be activated.
Signal light 2 – system error
On: An error has occurred in the alarm system. This could be due to a problem with the
battery, power supply or because of a problem with sensor monitoring, an error with the
GSM/GPRSor interferences. Contact customer service for assistance.
Flashing: There is an error in the alarm system’s memory which needs to be reset.
O: The system is free of errors.
Signal light 3 – tamper alarm
On: A tamper alarm has been triggered in the system. This could be due to failure or
sabotage. Contact customer service for assistance.
Flashing: There is a tamper alarm in the alarm system’s memory which needs to be
reset.
O: The system is free of tamper alarms.
Resetting
You can reset the alarm system by entering your personal code or using your
keytag. If there are various alarms triggered in the system memory, you will need to
repeat the rearming process until LED lights 1, 2 and 3 are all switched o.
HOW TO USE THE KEYPAD 7
SECTOR ALARM – DOMONIAL USER INSTRUCTIONS 4
How to use the alarm system
The alarm system is easy and convenient to operate using the
keypad, remote control or keytag.
Activating using the keypad
Full Arm mode (activates the entire alarm system)
Close all of the exterior doors and windows before activating the system.
Press the button Activating Full Arm mode.
The signal light 1 will light up and flash to confirm the command before switching o
again.
A warning alert will sound for a moment as you leave. In the case of a system error,
a warning tone will be emitted. You should rectify the system error and then try to
activate the system again.
Part Arm mode (activates part of the alarm system*)
Close all of the exterior doors and windows before activating the system.
Press the button Activating Part Arm mode.
The signal light 1 flash until the alarm is activated.
No warning alert will sound as you leave (If set to Part Arm silent). In the case of a
system error, a warning tone will be emitted. You should rectify the system error and
then try to activate the system again
*Part Arm mode is programmed according to your needs. The Sector Alarm Security Advisor will
program the alarm according to your preferences.
8 HOW TO USE THE ALARM SYSTEM
Activating using the remote control
Keep in mind that the remote control activates the system instantly. You should therefore be
careful not to activate the alarm until you are outside of the protected zone.
Full Arm mode (activates the entire alarm system)
Close all of the exterior doors and windows before activating the system.
Press the button Activating Full Arm mode.
The button confirmation light will light up for a few seconds to confirm activation. In the case of
a system error, you will need to rectify the error and then try to activate the system again.
Part Arm mode (activates part of the alarm system*)
Close all of the exterior doors and windows before activating the system.
Press the button Activating Part Arm mode.
The button confirmation light will light up for a few seconds to confirm activation. In the case of
a system error, you will need to rectify the error and then try to activate the system again.
Check status
To check the status of the system you press the status button with question mark and
the button of the current panel status will light for a few seconds.
*Part Arm mode is programmed according to your needs. The Sector Alarm Security Advisor will
program the alarm according to your preferences.
Panic Alarm function
Activating Full Arm mode
Deactivation button
Activating Part Arm mode
Status button
HOW TO USE THE ALARM SYSTEM 9
SECTOR ALARM – DOMONIAL USER INSTRUCTIONS 4
Deactivating using the keypad
Deactivate
The entire system will be deactivated, regardless as to whether it was in Full Arm mode or
Part Arm mode.
Enter your personal code or use the keytag.
The system light 1 will switch o.
When somebody enters the property, the system will generate a sound to indicate that
it is necessary to deactivate the alarm system.
Deactivating using the remote control
Deactivate
The entire system will be deactivated, regardless as to whether it was in Full Arm mode or
Part Arm mode.
Press the button Deactivation.
The LED confirmation light will light up for a few seconds to confirm the command.
When somebody enters the property, the system will generate a sound to indicate that it is
necessary to deactivate the alarm system.
Siren and sound
When an alarm is triggered the siren will sound. The sound will be generated from the smoke
detectors and indoor sirens if fitted.
You will have two dierent sounds depending on the type of alarm.
If the sound is constant, there has been a burglar alarm or a panic alarm
If the sound is pulsing, the system has detected smoke - - - - - - -
10 HOW TO USE THE ALARM SYSTEM
Tabla de contenidos
Otros manuales de Sistema de seguridad de Sector Alarm
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario