Seagull Models JU-87 STUKA Manual de usuario

ASSEMBLY MANUAL

Code: SEA284

“ Graphics and specications may change without notice “ .

JU-87 STUKA GIANT SCALE

Specications:

Wingspan---------------90 in (228.6 cm).

Wing area---------------1328.7 sq.in (85.7 sq.dm).

Weight-------------------17.6 lbs (8.0 kg).

Length-------------------68.3 in (173.4 cm).

Gasoline Engine--------38-50cc

Radio--------------------7 channels with 7 servos.

JU-87 Instruction Manual.

ank you for choosing the JU-87 ARF by SG MODELS . e JU-87 was designed

with the intermediate/advanced sport yer in mind. It is a semi scale airplane which

is easy to y and quick to assemble. e airframe is conventionally built using balsa, ply-

wood to make it stronger than the average ARF, yet the design allows the aeroplane to be

kept light. You will nd that most of the work has been done for you already. e motor

mount has been tted and the hinges are pre-installed. Flying the JU-87 is simply a joy.

is instruction manual is designed to help you build a great ying aeroplane. Please read

this manual throughly before starting assembly of your JU-87 . Use the parts listing below to

indentify all parts.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C ight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs oer a variety of

training procedures designed to help the new pilot on his way to successful R/C ight. ey

will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

KIT CONTENTS.

SEA284 JU-87 STUKA GIANT

1. Fuselage

2. Wing set

3. Tail set

4. Canopy

5. Cowling

6. Pilot

7. Aluminum wing tube

8. Wheel pants

ADDITIONAL ITEMS REQUIRED.

TOOLS & SUPPLIES NEEDED.

in cyanoacrylate glue.

Medium cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

read-lock.

Paper towels.

�38-50cc gasoline engine.

�Computer radio with 7 servos.

�Glow plug to suit engine.

�Propeller to suit engine.

�Protective foam rubber for radio

system.

HINGING THE AILERON.

2x10mm

Note: adjust decal rim straight away.

JU-87 Instruction Manual.

HINGING THE FLAP.

INSTALL THE AILERONS

CONTROL HORN.

Epoxy.

Aileron control horn.

Flap control horn.

Epoxy.

Fiberglass control horn

INSTALL FLAP CONTROL HORN.

INSTALL LED LIGHT.

Install the ap control horn using the

same method as same as the aileron con-

trol horns.

JU-87 Instruction Manual.

Epoxy.

HINGING THE FLAP FOR

CENTER WING.

1) Repeat steps to install hinging for

center wing as same as steps done for ai-

lerons.

2) en, t the joiner wire into the ap of

center wing as below pictures.

3) Slide the wing tube into the wing tube

socket.

4) Slide the wing panel into position,

guiding the extensions from the side

wing into center wing.

INSTALLING THE AILERON SERVOS.

Because the size of servos dier, you

may need to adjust the size of the precut

opening in the mount. e notch in the

sides of the mount allow the servo lead to

pass through.

1) Using a small weight (Weighted fuel

pick-up works well) and string, feed the

string through the wing as indicated.

2) Place the servo between the mounting

blocks and space it from the hatch. Use a

pencil to mark the mounting hole loca-

tions on the blocks.

JU-87 Instruction Manual.

3) Use drill bit in a pin vise to drill the

mouting holes in the blocks.

4) Apply 2-3 drops of thin C/A to each

of the mounting holes. Allow the C/A to

cure without using accelerator.

C/A glue

5) Use dental oss to secure the connec-

tion so they cannot become unplugged.

6) Secure the servo to the aileron hatch

using Phillips screwdriver and the screws

provided with the servo.

7) Apply 1-2 drops of thin C/A to each of

the mounting tabs. Allow the C/A to cure

without using accelerator.

8) Remove the string from the wing at

the servo location and use the tape to at-

tach it to the servo extension lead. Pull

the lead through the wing and remove

the string.

9) Set the aileron hatch in place and use a

Phillips screw driver to install it with four

wood screws.

INSTALLING THE FLAP SERVO.

Repeat the procedure as above for the

ap servo.

2x10mm

AILERON PUSHROD

INSTALLATION.

Please see below pictures.

100mm

M3 clevis. M3 lock nut.

JU-87 Instruction Manual.

INSTALLING THE FLAP PUSHROD.

INSTALLING THE LANDING GEAR.

Repeat the procedure as aileron push-

rod.

100mm

M3 clevis. M3 lock nut.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Juguete de Seagull Models

Seagull Models

Seagull Models Super Tucano T-27 Manual de usuario

Seagull Models

Seagull Models SPORT CRUISER Manual de usuario

Seagull Models

Seagull Models AT-6 TEXAN Manual de usuario

Seagull Models

Seagull Models Magic Star 3D EP Manual de usuario

Seagull Models

Seagull Models SEA 304 Manual de usuario

Seagull Models

Seagull Models MASTER SCALE KIT EDITION CLASSIC UGLY STICK... Manual de usuario

Seagull Models

Seagull Models SEA231 Manual de usuario

Seagull Models

Seagull Models BUNKER BU 133 Manual de usuario

Seagull Models

Seagull Models MINI CHRISTEN EAGLE II N54CE Manual de usuario

Seagull Models

Seagull Models MAXI LIFT 33cc Manual de usuario

Seagull Models

Seagull Models Ryan Navion Manual de usuario

Seagull Models

Seagull Models Savage Cruiser Manual de usuario

Seagull Models

Seagull Models SHOCK-CUB 35-55cc Manual de usuario

Seagull Models

Seagull Models SWIFT40 Manual de usuario

Seagull Models

Seagull Models Funfly 3D Manual de usuario

Seagull Models

Seagull Models SEA 302 Manual de usuario

Seagull Models

Seagull Models Mitchell B-25 Manual de usuario

Seagull Models

Seagull Models JUMPER 25 Manual de usuario

Seagull Models

Seagull Models SEA 334 Manual de usuario

Seagull Models

Seagull Models Mini Nemsis EP Manual de usuario

Seagull Models

Seagull Models SEA230B Manual de usuario

Seagull Models

Seagull Models SPARROW HAWK 1.6-2.0 Manual de usuario

Seagull Models

Seagull Models Turbo Raven Manual de usuario

Seagull Models

Seagull Models Grumman F8F Bearcat Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario