Seagull Models AT-6 TEXAN Manual de usuario
MadeinVietnam.
Specifications:
Wingspan-------------------------------------------------- 62.9in---------------------------------------159.8cm.
Wingarea--------------------------------------------------620sq.in----------------------------------40sq.dm.
Approximateflyingweight-----------------------------6.2-7.7lbs---------------------------2.8kg -3.5kg.
Length------------------------------------------------------43.6in----------------------------------------110.8cm.
Recommendedenginesize--------------------------.40 -.52cu.in---------------------------------2-stroke.
------.72 - .82 cu.in-------------------------------- 4-stroke.
ELECTRICCONVERSION:OPTIONAL.
RecommendedR/C---------------------------------------------4channels with 6 servos.
Flyingskilllevel----------------------------------------------------Advanced/Intermediate.
Kit features.
• Ready-made—minimalassembly&finishingrequired.
• Ready-covered—includingdecals,trim&covering.
• Factory-installedpushrod.
• Photo-illustrated step-by-step AssemblyManual.
MS:110
“Graphics and specifications may change without notice”.
ASSEMBLY MANUAL
AT-6 TEXAN _ CODE SEA 110.
2
INTRODUCTION.
Thank you for choosing the AT-6 TEXAN ARTF by SEAGULL MODELS. The AT-6 TEXAN was
designedwiththeintermediate/advancedsportflyerinmind.Itisa semiscaleairplane whichiseasy
to fly and quick to assemble. The airframe is conventionally built using balsa, plywood to make it
stronger than the average ARTF , yet the design allows the aeroplane to be kept light. You will find
thatmostoftheworkhasbeendoneforyoualready.Themotormounthasbeenfittedandthehinges
are pre-installed . Flying the AT-6 TEXAN is simply a joy.
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your AT-6 TEXAN . Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilot onhiswaytosuccessfulR/Cflight. Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
ADDITIONAL ITEMS REQUIRED.
.40-.52 cu.in 2-stroke engine.
.72-.82cu.in 4-stroke engine.
4 channels with 6 servos.
Computer radio with nine servos.
Glow plug to suit engine.
Propeller to suit engine.
Protective foam rubber for radio
system.
Siliconefuel line.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
(1) Canopy.
WING ASSEMBLY
(1) Right wing half/ aileron.
(1) Left wing half/ aileron.
(1)Midle wing.
Tail section assembly
(1) Horizontal stabilizer/ elevator
halves.
(1) Rudder halves.
Some more parts.
HARDWAREPACK
COWLING
Landinggear.....
3
www.seagullmodels.com
NOTE:To avoid scratching your new aero-
planewesuggestthatyoucoveryour
workbench with an old towel. Keep a
couple of jars or bowls handy to hold
the small parts after you open the
bags.
Pleasetrialfitallparts.Makesureyou
havethecorrectpartsandthattheyfit
andarealignedproperlybeforegluing!
This will ensure proper assembly as
the AT-6 TEXAN is made from
natural materials and minor adjust-
ments may have to be made. The
paintand plastic partsused in thiskit
are fuel proof. However, they are not
tolerant of many harsh chemicals in-
cluding the following: paint thinner,
cyano-acrylate glue accelerator, cy-
anoacrylate glue de-bonder and
acetone. Do not let these chemicals
come in contact with the colours on
the covering and the plastic parts.
The control surfaces, including the
ailerons, elevators, and rudder, are
prehinged with hinges installed, but
the hinges are not glued in place. It
is imperative that you properly
adhere the hinges in place per the
steps that follow using a high-quality
thin C/A glue.
1) Carefully remove the aileron from one
of the wing panels. Note the position of the
hinges.
2)Removeeach hingefromthe wingpanel
and aileron and place a T-pin in the center of
each hinge. Slide each hinge into the aileron
untilthe T-pinissnug againstthe aileron.This
will help ensure an equal amount of hinge is
oneithersideofthe hingelinewhentheaileron
is mounted to the wing panel.
HINGING THE AILERONS.
Note:
Hinge.
T-pin.
3) Slide the aileron on the wing panel until
there is only a slight gap. The hinge is now
centered on the wing panel and aileron.
Remove the T-pins and snug the aileron
against the wing panel.A gap of 1/64” or less
shouldbe maintainedbetween thewing panel
andaileron.
4)Deflect the aileron and completely
saturate each hinge with thin C/A glue. The
aileronsfrontsurface shouldlightlycontact the
wing during this procedure. Ideally, when the
Thehinge is constructed of a special
material that allows the C/A to wick
or penetrate and distribute
throughout the hinge, securely
bonding it to the wood structure of
the wing panel and aileron.
hinges are glued in place, a 1/64” gap or less
will be maintained throughout the lengh of the
aileron to the wing panel hinge line.
Note:
T-pin.
Hinge.
AT-6 TEXAN _ CODE SEA 110.
4
HINGING THE ELEVATORS.
Glue the elevator hinges in place using the
same techniques used to hinge the ailerons.
HINGING THE RUDDER.
Glue the rudder hinges in place using the
same techniques used to hinge the ailerons.
8)Afterboth ailerons aresecurely hinged,
firmly grasp the wing panel and aileron to
make sure the hinges are securely glued and
cannot be pulled out. Do this by carefully
applying medium pressure, trying to separate
the aileron from the wing panel. Use caution
not to crush the wing structure.
7) Repeat this process with the other wing
panel, securely hinging the aileron in place.
6) Using C/A remover/debonder and a
papertowel, removeanyexcess C/Aglue that
may have accumulated on the wing or in the
aileronhinge area.
5)Turnthewing paneloverand deflectthe
aileron in the opposite direction from the
opposite side. Apply thin C/A glue to each
hinge,makingsurethattheC/Apenetratesinto
both the aileron and wing panel.
C/Aglue.
Worktheaileronupanddownseveral
times to “work in” the hinges and
check for proper movement.
Note:
Apply epoxy glue.
Hinge.
WING TIP INSTALLATION .
Fillepoxy.
Removecovering.
5
www.seagullmodels.com
Aileron control horn: See pictures below.
AILERON CONTROLHORN
2 sets.
3x35mm.
Maskingtape.
CONTROL HORN
M3 SCREW.
18mm.
Epoxy.
ALUMINUMWASHER.
M3LOCKNUT.
ALUMINUMWASHER.
Epoxy.
Install the wing edge to the wing.
AT-6 TEXAN _ CODE SEA 110.
6
Install the elevator control horn using the
same method as with the aileron control
horns.
ELEVATOR CONTROL HORN. Rudder control horn:
Using the same techniques used aileron
control horn. See picture below.
RUDDER CONTROL HORN.
18mm.
Epoxy.
Elevatorcontrolhorn.
Horizontal
Stabilizer.
AluminumWasher.
CONTROL HORN M3
M3LOCKNUT.
Epoxy.
AluminumWasher.
2 sets.
3x30mm.
1 sets.
3x30mm.
CONTROL HORN
M3SCREW.
ALUMINUMWASHER.
ALUMINUMWASHER.
M3LOCKNUT.
EPOXY.
EPOXY.
Fuselage.
18mm.
Rudder.
7
www.seagullmodels.com
Servo arm.
loctile
secure.
Adjustableservo
connector.
25mm.
Servo for retractable only.
Metalconnector.
Servo arm.
25mm.
SERVO GEAR INSTALLATION.
Remove covering.
Remove covering.
Electric wire.
Wing bottom.
PUSHROD INSTALLATION.
M3x25mm.
Rudder control horn.
14
23
5
3mm.
AT-6 TEXAN _ CODE SEA 110.
8
3 x 25 mm.
2 x 6 mm.
12
2
3
5
4
Pushrod.
Metalclevis.
M3lock.
9
www.seagullmodels.com
Open Position
Servo arm.
Repeat procedure for other landing gear.
Close Position
Servo arm.
12 mm.
Epoxy.
AT-6 TEXAN _ CODE SEA 110.
10
epoxy.
WING ASSEMBLY.
epoxy.
Otros manuales para AT-6 TEXAN
2
Tabla de contenidos
Otros manuales de Juguete de Seagull Models
Seagull Models
Seagull Models GLASAIR SPORTSMAN 2-2 Manual de usuario
Seagull Models
Seagull Models Laser 200 Manual de usuario
Seagull Models
Seagull Models Arising Star Manual de usuario
Seagull Models
Seagull Models ZLIN 50 Manual de usuario
Seagull Models
Seagull Models Sparrow Hawk SEA-93 Manual de usuario
Seagull Models
Seagull Models PILATUS B4 Manual de usuario
Seagull Models
Seagull Models A6M Zero Fighter 67 Manual de usuario
Seagull Models
Seagull Models Decathlon 60-85cc-3D Manual de usuario
Seagull Models
Seagull Models YAKOVLEV YAK 3 Manual de usuario
Seagull Models
Seagull Models Super Decathlon ARF 120 Manual de usuario
Seagull Models
Seagull Models NIEUPORT 28 REPLICA Manual de usuario
Seagull Models
Seagull Models SEA 94 Pilatus PC-9 Manual de usuario
Seagull Models
Seagull Models MINI CHRISTEN EAGLE II N54CE Manual de usuario
Seagull Models
Seagull Models Cessna L-19A Bird Dog Manual de usuario
Seagull Models
Seagull Models Ultimate Manual de usuario
Seagull Models
Seagull Models PERCIVAL MEW GULL Manual de usuario
Seagull Models
Seagull Models GLASAIR Sportsman GS-2 Manual de usuario
Seagull Models
Seagull Models Shoestring SEA143 Manual de usuario
Seagull Models
Seagull Models ERCOUPE Manual de usuario
Seagull Models
Seagull Models CHEROKEE Manual de usuario
