Seagate HAWK 2LP ST31231N Manual de usuario
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HAWK 2LP Family:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ST32430N/ND
ST31230N/ND
ST31231N
Contents
Introduction ...................................................................... 1
Electromagnetic interference ........................................... 1
Before you begin.............................................................. 3
Installation overview ........................................................ 8
Product Repair ................................................................. 10
Shipping.................................................................... 11
Product Repair and return information ..................... 11
Technical support services .............................................. 12
Hawk 2LP family product information .............................. 15
Initial set-up information................................................... 17
Drive configuration ........................................................... 22
Drive installation .............................................................. 30
© 1995 Seagate Technology, Inc. All rights reserved
Publication Number: 77767499, Revision A
September 1995
Seagate®, Seagate Technology®and the Seagate logo are
registered trademarks of Seagate Technology, Inc. HawkTM,
SeaFAXTM, SeaFONETM, SeaTDDTM, and SeaBOARDTM, are
trademarksofSeagateTechnology,Inc.Otherproductnames
are registered trademarks or trademarks of their own.
Seagate reserves the right to change, without notice, product
offerings or specifications. No part of this publication may be
reproduced in any form without written permission of Seagate
Technology, Inc.
Hawk 2LP Family Installation Guide, Rev. A 1
____________________________________________________________________________________________________________
Introduction
This manual is organized to assist you in the installation and
operationofyourSeagateHawk2LPFamilydiscdrive.Family
models are listed in Hawk 2LP Family Product Information
section.It alsoprovides informationto aid inobtaining service
for the drive.
Before attempting any installation, please read through all
applicable sections of this document, including all warnings
and cautions.
Warning.
This equipment generates, uses, and can radiate radio
frequency energy andifnotinstalledandused in accordance
with these instructions, may cause interference to radio com-
munications.
Electromagnetic interference (EMI) considerations
The drive(s) described herein, as delivered, are designed for
system integration and installation into a suitable enclosure
prior to use. As such, the drive(s) described herein are sup-
plied as a sub-assembly and are not subject to Subpart J of
Part 15 of the FCC Rules and Regulations nor the Radio
InterferenceRegulationsoftheCanadianDepartmentofCom-
munications. However, the unit has been tested using proper
shielding and grounding and found to be compliant with the
Class A limits of the FCC Rules and the Regulations of the
Canadian Department of Communications.
2 Hawk 2LP Family Installation Guide, Rev. A
_____________________________________________________________________________________________________________
The physical design characteristics of the drive(s) described
herein, serve to minimize EMI radiation when installed in an
enclosure that provides reasonable shielding. As such, the
drive(s) are capable of meeting the Class B limits of the FCC
Rules and the Regulations of the Canadian Department of
Communications.
Note. It is the end users' responsibility to assure that the
drive(s) described herein meet the appropriate EMI
requirements of their system. Shielded I/O cables
may be required if the enclosure does not provide
adequate shielding. If I/O cables are external to the
enclosure, shielded cables should be used, with the
shields grounded to the enclosure and to the host
controller.
Hawk 2LP Family Installation Guide, Rev. A 3
_____________________________________________________________________________________________________________
Before you begin
Verify that the system is switched off and disconnected
from main power before any installation is attempted.
Protect yourself, the drive, and your valuable programs
and data by reading the following cautions and warnings.
• Do not tamper with sealed top cover. Doing so voids your
warranty. The drive contains no user serviceable compo-
nents. See Product Repair section for more information.
• Visually inspect the shipping container for any obvious
damage.
• Verify all parts listed on shipping bill are received with the
equipment. Discrepancies or damage should be reported to
the shipping company.
• Inspectdrivefor possible shippingdamage.Allclaimsofthis
type should be filed promptly with the transporter involved.
Saveoriginalpackingmaterialstobeusedwhen reshipping.
4 Hawk 2LP Family Installation Guide, Rev. A
_____________________________________________________________________________________________________________
• When transporting or shipping a drive or system, please
ensure that they are correctly packed in original Seagate
approved (or equivalent) container and shipped via an air-
ride carrier experienced in handling computer equipment.
• Donotunpack drive fromits static shieldedbag untilyou are
ready to install it in the system.
• Always handle the drive by the frame or casting.
• Donottouch Printed CircuitBoard (PCB) or theI/O connec-
tor pins.
• Never apply pressure to the PCB or to the drive top cover
Caution. Thecircuit assembliesandcomponentscontained
inthis equipment canbedegraded ordestroyed by
Electrostatic Overstress (EOS) or by Electrostatic
Discharge (ESD).
Hawk 2LP Family Installation Guide, Rev. A 5
_________________________________________________________________________________________________________________
Static electrical charges can accumulate quickly
onpersonnel,clothingandsyntheticmaterials.The
electrostatic fields due to these charges when
brought in close proximity to susceptible circuit
assemblies and components, can result in de-
graded reliability or immediate failure of the affect-
ed component or assembly.
To insure optimum reliable equipment operation, it
is required that technical support personnel dis-
charge themselves by wearing a grounding strap
around the wrist and be connected to a grounding
terminal while working in the vicinity of, and while
handling EOS/ESD susceptible assemblies/parts.
Ifunavailable,ground yourself frequentlyby touch-
ingthemetalchassisofthesystembeforehandling
any components (this helps only if the system is
connected to a ground).
Avoid static-inducing car-
peted areas.
This procedure is especially impor-
tant when handling printed circuit boards (PCB's).
6 Hawk 2LP Family Installation Guide, Rev. A
_____________________________________________________________________________________________________________
Safety instructions
1. Thedisc drive(s) are tobe installed ina customersupplied
enclosure where the surrounding air does not exceed
50oC.
2. Four (4) 6-32UNC-2Ascrews are requiredfor installation.
Maximum screw length into side of drive is 0.15 inches
(3.81 mm). Maximum screw length into bottom is 0.20 in.
(5.08mm). Screwtighteningtorques is6.0lb-in (.675NM)
max with minimum thread engagement of 0.12 in (3.00
mm).
3. The power requirements are shown in the Product Infor-
mation section.
4. The power supplymustsatisfy the safetyrequirements for
SELV (Safety Extra Low Voltage) circuits.
5. Service is to be provided by trained Seagate service
personnel.
6. The incorporation of the disc drives listed in this guide into
a customer enclosure must meet the appropriate safety
requirements of the country in which it is used (e.g. UL
1950,CAN/CSA-C22.2No.950-M89,DINVDE0805:1993
and EN60950: 1992 (IEC 950).
Note
Power must be off when connecting or disconnecting.
Hawk 2LP Family Installation Guide, Rev. A 7
_____________________________________________________________________________________________________________
Sicherheitsanleitung
1. Däs Gerät ist ein Einbaugerät, vorgesehen für eine
maximale Umgebungstemperatur von 50oC.
2. Zur Befestigung der Drive werden 4 Schrauben benötigt
(6-32 UNC-2A). Die maximale Länge der Schrauben in
der unteren Seite des Chassis darf nicht mehr als 0.20 in
(5.08 mm) betragen, die in der Seiten 0.15 in (3.81 mm).
Maximalle Schraubenanziehung von 6.0 in-lb (.675 NM)
mit minimalem Gewindeansperuch .12 in (3.00 mm).
3. Die Versorgungsspannungen werden in der Sektion
Produkt Information gezeigt.
4. Die Versorgungsspannung muss SELV entsprechen.
5. Alle Arbeiten dürfen nur von ausgebildetem Seagate
Service-Personal durchgefürhrt werden.
6. Der Einbau des Drives muss den Anforderungen gemäss
DIN VDE 0805:1993 oder EN60950:1992 (IEC 950).
Vorsicht
Ánsehluss oder Entfernung oler Geräteverbindung nur bei
abgeschalteter Versorgungsspannung vornehmen.
8 Hawk 2LP Family Installation Guide, Rev. A
_____________________________________________________________________________________________________________
Installation Overview
Installation of the drive can be divided into distinct phases.
Some of these may not be applicable to all system installation
requirements.Refer to theindividual driveinstallationsections
for specific information on your drive model.
•Drive configuration: Select those drive features that are
appropriate to install the drive in the system. This is done by
installing or removing user configuration jumpers found on
the drive PCB.
•Mechanical installation: After setting up the drive configu-
ration the drive must be mechanically installed into the host
system and the power and I/O cables attached. Previously
mentioned precautions should be observed.
• CMOS configuration: SCSIdrivesshould not bedefinedin
the CMOS. The SCSI host adapter uses its own BIOS to
handle the Input/Output procedures. The CMOS setting for
SCSI drive is either drive type zero, or the no drive installed
option.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Almacenamiento de Seagate
Seagate
Seagate ST3320410SV - SV35.4 Series 320 GB Hard... Instrucciones de funcionamiento y seguridad
Seagate
Seagate ST318203FC Manual de usuario
Seagate
Seagate DB35.3 Series Serial ATA Manual de usuario
Seagate
Seagate ST3160215ACE Manual de usuario
Seagate
Seagate ST10000NM0006 Manual de usuario
Seagate
Seagate Enterprise Capacity 2.5 HDD Constellation Manual de usuario
Seagate
Seagate ST9500421AS - Momentus 7200 FDE 500 GB Hard... Manual de usuario
Seagate
Seagate GoFlex Desk Manual de usuario
Seagate
Seagate NAS 400 Manual de usuario
Seagate
Seagate ST336732LC Manual de usuario
Seagate
Seagate ST3100011A - 100GB UDMA/100 7200RPM 2MB IDE Hard... Manual de usuario
Seagate
Seagate Momentus 5400 Manual de usuario
Seagate
Seagate FreeAgent Desktop 1TB Manual de usuario
Seagate
Seagate STU62001LW-S Manual de usuario
Seagate
Seagate GoFlex Turbo Manual de usuario
Seagate
Seagate ST310014ACE Manual de usuario
Seagate
Seagate ST973401LC - Savvio 73.4 GB Hard Drive Manual de usuario
Seagate
Seagate Cheetah 10K.7 FC Manual de usuario
Seagate
Seagate ST9100824A - Momentus 5400.2 100 GB Hard... Manual de usuario
Seagate
Seagate Barracuda Pro ST14000DM001 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario