Seafloor TriDrone Manual de programación

- TriDrone USV

- TriDrone Carry Case

- TriDrone Hardware Kit

- Data Collector Cable

- Accessory Pouch

-Spektrum Remote

Control with case

-USB Drive

-Mast

IMPORTANT

THANK YOU FOR PURCHASING SEAFLOOR SYSTEMS' PRODUCTS FOR YOUR SURVEYING NEEDS.

Please read through all of these Instructions and tips before proceeding with the operation. We do our best

to provide a simple setup process for all applications however please contact your nearest authorized

dealer if you encounter issues.

Always disconnect any power sources connected to your vessel before servicing vessel or accessories.

PRODUCT INCLUDES:

STEP: 1

Remove the vessel from the

case. Remove the remote case

from the top of the lid. Remove all

accessories from accessory pouch

located at the bottom of the case.

QUICKSTART INSTRUCTIONS

TriDrone Portable Remote Surveying Vessel

QUICKSTART INSTRUCTIONS

STEP: 2

Attach the thruster to the rear bracket of the vessel and secure by tightening

retaining screw.

STEP: 3

Insert fully charged 4S battery

and connect to power

distribution cable.

STEP: 4

Open bow hatch lid with provided hatch wrench,

and remove lid.

STEP: 5

Run the data collector cable through the inside of the hull through to the

hull hatch lid.

QUICKSTART INSTRUCTIONS

STEP: 6

Connect data collector cable to

transducer.

STEP: 8

Connect the thruster cable to the bulkhead

located at the stern of the vessel.

STEP: 7

Attach antenna to the mounting screw located at the front of the frame.

QUICKSTART INSTRUCTIONS

Operation: Be sure to observe and follow all local water safety regulations and procedures. Always

operate vessel within line of sight, and immediately stop operation if hazards or safety risks arise.

Your setup is now complete.

Welcome to the Seafloor Squad!

WARRANTY INFORMATION

For warranty information, visit https://www.seafloorsystems.com/terms-and-conditions 4415 Commodity Way, Shingle

Springs, CA, 95682 • 530-677-1019 https://www.seafloorsystems.com/

STEP: 9

Switch power to the "On" position.

STEP: 10

Connect the remote by holding the power button for

approximately 2 seconds. The remote will beep when

activated. You are now ready to survey.

Tabla de contenidos

Otros manuales de Equipos marinos de Seafloor

Seafloor

Seafloor EchoBoat-240 Manual de usuario

Seafloor

Seafloor Sonarmite Manual de usuario

Seafloor

Seafloor AutoNav PLUS Manual de usuario

Seafloor

Seafloor HyDrone ASV Manual de usuario

Seafloor

Seafloor EchoBoat 160 ASV Manual de usuario

Seafloor

Seafloor HydroLite-DFX Manual de usuario

Seafloor

Seafloor HydroCat 180 Manual de usuario

Seafloor

Seafloor AutoNav Manual de usuario

Manuales populares de Equipos marinos de otras marcas

Clarion

Clarion CMS2 Manual de reparación

EBS

EBS M7000 Manual de usuario

Kongsberg

Kongsberg M3 Bathy Manual de usuario

NPK

NPK SCS-1002 Manual de usuario

Furuno

Furuno FE-800 Manual de usuario

Harken

Harken 1561 Manual de usuario

Simrad

Simrad DD15 Manual de usuario

Notifier

Notifier FS-BSO Manual de usuario

Raymarine

Raymarine ST40 Manual de usuario

E2S

E2S E2XS112UL Manual de usuario

R2Sonic

R2Sonic 2026 Manual de usuario

COBHAM

COBHAM SAILOR 6000 Manual de usuario

Clarion

Clarion GR10BT Manual de reparación

Raymarine

Raymarine Maxiview ST80 Guía del usuario

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Instrucciones de montaje

Raymarine

Raymarine ST60 Tridata Guía del usuario

olympia electronics

olympia electronics ΒS-531/1/MAR Manual de usuario

Sonic

Sonic 2024 Manual de usuario