SDX Audio FT-5 Manual de usuario

SDX 60N/180/420N

FT-5 Telephone Guide

By SDX Business Systems plc

38HTN00027PEA - Issue 5 (February 1997)

ContentsContents

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Using the FT-5Using the FT-5 ....................................................................................................................................................................................................................33

Introduction........................................................................................................................3

Answering Calls................................................................................................................3

Making Calls......................................................................................................................4

Page..................................................................................................................................4

Pick-Up..............................................................................................................................5

Call Back...........................................................................................................................5

Hold (A Single Line Under A Button)................................................................................6

Hold (A Group Of Lines Under A Single Button)..............................................................6

Transferring Calls..............................................................................................................6

Conferencing.....................................................................................................................6

Group................................................................................................................................6

Privacy...............................................................................................................................7

Voluntary Account Code (Outgoing Calls Only)...............................................................7

Forced Account Code (Outgoing Calls Only)...................................................................7

Forced Pin Codes (Outgoing Calls Only).........................................................................7

Roaming Pin Codes (Outgoing Calls Only)......................................................................8

Camp-On To A Busy Extension (Internal Calls Only)......................................................9

Loudspeaker Monitor........................................................................................................9

PABX Recall......................................................................................................................9

Programming Selection Keys.........................................................................................10

Storing External Numbers...............................................................................................10

Ringing Mode..................................................................................................................11

Changing From LD To MF Signalling.............................................................................11

Lamp States....................................................................................................................11

ContentsContents

Using the FT-5Using the FT-5 – Page– Page 33

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Using the FT-5Using the FT-5

IntroductionIntroduction The FT-5 TerminalFT-5 Terminal, used in conjunction with your telephone system,

offers greater control of telephone traffic by means of single key access

and flashing lamp indications.

Exchange lines can be answered and accessed selectively rather than in

the normal queued mode, giving increased flexibility in traffic

management.

An FT-5 TerminalFT-5 Terminal has 14 Selection Keys and Busy Lamps which can be

programmed to represent a Line, an Extension, a Group of Lines or a

Group of Extensions. The FT-5 TelephoneFT-5 Telephone can take a headset via a

switched junction box for headset/handset operation. The headset fitted

mustmust be an SDX headset.

Answering CallsAnswering Calls To answer an incoming call from a line or group (Medium flash of aTo answer an incoming call from a line or group (Medium flash of a

field lamp)field lamp)::

1. Press the associated key to answer the call.

2. When field lamp goes to Fast Flash.Fast Flash.

3. Lift handset and speak.

If your terminal is ringing when there is no incoming call appearing on a

field lamp, the call is either an internal or external line which does not

have a lamp appearance on your FT-5.

To answerTo answer::

1. Lift handset to answer.

PagePage 44

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Making CallsMaking Calls Any call can be dialled on-hook; lift handset when called party answers.

To call another extensionTo call another extension::

1. Key extension number.

To call an external numberTo call an external number::

1. Press 99 then key external number.

To call a personal stored numberTo call a personal stored number::

1. Press ## then select from the 00/0400/04 stores (see Storing ExternalStoring External

NumbersNumbers).

To call a central directory numberTo call a central directory number::

1. Press ## then select from the Central Speed Store.

To repeat last number dialledTo repeat last number dialled::

1. Press ## then .

Call an Extension with a Field LampCall an Extension with a Field Lamp

To call an idle extension (lamp Off)To call an idle extension (lamp Off)::

1. Press the required extension key.

2. Field lamp flashes at Medium RateMedium Rate if ringing extension is an FT-1, 2,

3 or 4.

3. Field lamp goes to Fast FlashFast Flash during the call.

Note: You cannot transfer an external call to an extension in this manner.

External Call on a specific LineExternal Call on a specific Line

To select an external line (lamp Off)To select an external line (lamp Off)::

1. Press the appropriate key to seize the line.

2. Field lamp goes to Fast FlashFast Flash during the call.

PagePage You can pagepage over the loudspeakers of all free extensions in a group or

on the system and optionally wait for an answer from an extension.

To make a page callTo make a page call::

1. Press and dial 7.7.

2. Dial in extension or group number.

3. Lift handset and make announcement.

To answer page callTo answer page call::

1. Press * and dial 8.8.

2. Lift handset and speak.

Using the FT-5Using the FT-5 – Page– Page 55

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Pick-UpPick-Up If an extension lamp indicates that it is being rung (Medium flash) andIf an extension lamp indicates that it is being rung (Medium flash) and

you wish to answer the callyou wish to answer the call::

1. Press the extension key, lift handset and speak

If you hear another extension ringing that you wish to answer (butIf you hear another extension ringing that you wish to answer (but

there is no extension appearance on your FT-5)there is no extension appearance on your FT-5)::

1. Press FunctionFunction and Pick-upPick-up.

2. Lift the handset.

You must define the scope of the call Pick-up feature by programming a

Pick-upPick-up number to indicate which ringing extensions you wish to answer.

The Pick-upPick-up number can either be an extension or a group number. The

original programming of your SDX puts allall extensions in group 10. See

your System Manager for details of local group numbers.

To program pick-up numberTo program pick-up number::

1. While off-hook, press , dial 0101 and press .

2. Dial Pick-upPick-up group or extension number.

3. Replace handset.

Call BackCall Back If you dial an extension and hear busy tone, you can tell SDX to ring you

when the extension becomes free. Similarly, if you call an extension and

there is no answer, then you can tell SDX to call you back after that

extension is next used.

To request another extension to call back when freeTo request another extension to call back when free::

1. Dial extension and hear busy tone.

2. Press 22 and replace handset (if off hook).

You will be automatically called back when the extension becomes free:

To request another extension to call back when next usedTo request another extension to call back when next used::

1. Dial extension.

2. Press 22 and replace handset (if off hook).

You can make and receive calls whilst waiting for a call back.

PagePage 66

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Hold (A Single Line Under A Button)Hold (A Single Line Under A Button)

An External Call - System WideAn External Call - System Wide

To hold a single line that you are using (lamp Fast Flash) so thatTo hold a single line that you are using (lamp Fast Flash) so that

anyone can answer itanyone can answer it::

1. Press the line key on the FT-5.

2. Field lamp shows Slow FlashSlow Flash (on hold) on your extension.

3. To return to the call press the line key again.

4. The field lamp shows Fast FlashFast Flash again.

Automatic System HoldAutomatic System Hold

If you are connected to an external line and you wish to answerIf you are connected to an external line and you wish to answer

another callanother call::

1. Press the key indicating the incoming call (Medium FlashMedium Flash).

2. The connected line (Fast FlashFast Flash) is automatically placed on system

hold (Slow FlashSlow Flash) and you are connected to the new caller.

Hold (A Group Of Lines Under A Single Button)Hold (A Group Of Lines Under A Single Button)

To hold a line from a group of linesTo hold a line from a group of lines::

1. Press HH and replace handset.

2. To return to the call press and dial 9.9.

3. Lift the handset.

Transferring CallsTransferring Calls To transfer an external call to another extensionTo transfer an external call to another extension::

1. Press HH and dial the internal extension (announce call if necessary).

2. Press Ans/RlsAns/Rls or replace handset to transfer the call.

OROR

3. Press HH to return to caller.

If the call is transferred over a DPNSS network to a busy extension, you

may need to dial 33 before replacing the handset.

ConferencingConferencing You can set up a conference between an external line, another internal

extension and yourself or yourself and up to 30 other internal extensions.

To conference one call to anotherTo conference one call to another::

1. Press HH.

2. Dial the internal extension and wait until answered.

3. Press FunctionFunction.

4. Press ConfConf to establish a three party conference.

GroupGroup Group Working is used to ensure that there is always someone to answer

external calls. If you are a member of a group you can join or leave your

Group at will.

To join your answering groupTo join your answering group::

1. Press and dial 3.3.

Using the FT-5Using the FT-5 – Page– Page 77

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

2. Press any three digits.

To leave your answering groupTo leave your answering group::

1. Press .

2. Press 4.4.

This command is only effective after a 33 command.

PrivacyPrivacy You can inhibit other parties from listening in to your call or barging in.

To ensure privacyTo ensure privacy::

1. Press FunctionFunction followed by SecureSecure.

This inhibition is effective until you remove it.

To remove this inhibition at any timeTo remove this inhibition at any time::

1. Press FunctionFunction followed by SecureSecure.

Voluntary Account Code (Outgoing Calls Only)Voluntary Account Code (Outgoing Calls Only)

When you are connected to an external line you can enter an AccountAccount

CodeCode of up to 12 digits which will be included on the billing record and

printed on the call log.

To enter the account codeTo enter the account code::

1. Dial the external number and press ##.

2. Dial 0101, press and enter the account code.

If the account code is entered incorrectlyIf the account code is entered incorrectly::

1. Press to delete Account CodeAccount Code and re-enter correct code.

You can only delete an incorrectly entered account code prior to dialling

the last digit.

Forced Account Code (Outgoing Calls Only)Forced Account Code (Outgoing Calls Only)

A terminal may be programmed by the System Manager to force a user

to enter an account code (up to 12 digits) before an external call can be

made.

To make an external call when terminal has been set up for forcedTo make an external call when terminal has been set up for forced

account codeaccount code::

1. Dial 99. You will hear an intermittent tone.

2. Enter the account code. If dial tone is not returned, then press ##.

3. Then, when you hear dial tone, dial the required external number.

Forced Pin Codes (Outgoing Calls Only)Forced Pin Codes (Outgoing Calls Only)

A terminal may be programmed by the System Manager to force a user

to enter a PIN number (up to 6 digits) before an external call can be

made.

To make an external call when terminal has been set up for a forcedTo make an external call when terminal has been set up for a forced

PIN codesPIN codes::

1. Dial 9.9. You will hear an intermittent tone and the display shows.

2. Enter the PIN number. If dial tone is not returned, then press #.

3. Then, when you hear dial tone, dial the required external number.

PagePage 88

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

If an unauthorised PIN code is entered a number unobtainable tone (fast

repeated tone) is heard.

Roaming Pin Codes (Outgoing Calls Only)Roaming Pin Codes (Outgoing Calls Only)

At terminals that do not have a PIN Code allocated to them, it is possible

to override call barring

To make an external call from a terminal that has not been set up forTo make an external call from a terminal that has not been set up for

forced PIN codesforced PIN codes::

1. Press and dial 66. You will hear an intermittent tone.

2. Enter the PIN number. If dial tone is not returned, then press ##.

3. Then, when you hear dial tone, dial the required external number.

If an unauthorised PIN code is entered a number unobtainable tone (fast

repeated tone) is heard.

Roaming Pin Codes (Outgoing Calls Only)Roaming Pin Codes (Outgoing Calls Only)

At terminals that do not have a PIN Code allocated to them, it is possible

to override call barring

To make an external call from a terminal that has not been set up forTo make an external call from a terminal that has not been set up for

forced PIN codesforced PIN codes::

1. Press and dial 66. You will hear an intermittent tone.

2. Enter the PIN number. If dial tone is not returned, then press ##.

3. Then, when you hear dial tone, dial the required external number.

If an unauthorised PIN number is entered, a number unobtainable tone

will be heard (fast repeated tone).

Using the FT-5Using the FT-5 – Page– Page 99

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Camp-On To A Busy Extension (Internal Calls Only)Camp-On To A Busy Extension (Internal Calls Only)

To camp-on to a busy extension or group (lamp On)To camp-on to a busy extension or group (lamp On)::

1. While off-hook, press the associated key - you will hear busy tone

2. Press FunctionFunction.

3. Press Camp-onCamp-on to camp-on to extension or group. Do not hang-upDo not hang-up.

4. Line lamp remains on.on.

If the call is unanswered after the time-out period it is returned to the FT-5

with the line lamp On.On.

Loudspeaker MonitorLoudspeaker Monitor

An FT-5 TelephoneFT-5 Telephonehas a loudspeaker that is used when you choose to

set up a call while on-hook.

If during a call you are using the handset and you wish to listen overIf during a call you are using the handset and you wish to listen over

the loudspeakerthe loudspeaker::

1. Press FunctionFunction followed by SpeakerSpeaker. Do notnot replace handset.

This feature allows you to monitor (or listen to) calls only. It does not

allow conversation.

PABX RecallPABX Recall When your SDX system is installed “behind” a PABX and you areWhen your SDX system is installed “behind” a PABX and you are

connected to a line, to recall the PABXconnected to a line, to recall the PABX::

1. Press FunctionFunction followed by RecallRecall.

PagePage 1010

SDX 60/180/420 FT-5 Telephone GuideSDX 60/180/420 FT-5 Telephone Guide 38HTN00027PEA - Issue 5 (February 1997)38HTN00027PEA - Issue 5 (February 1997)

Programming Selection KeysProgramming Selection Keys

The 14 Selection Keys can be programmed to represent either lines,

extensions, groups of lines or groups of extensions.

To program the Selection KeysTo program the Selection Keys::

1. Lift the handset.

2. Press and dial 0.0.

3. Press the Selection Key to be programmed.

4. Enter 4-digit personal password (consult your System Manager).

5. Press to cancel any current designation.

6. Enter new designation as follows:

–Exchange Lines:Exchange Lines: Key the line number (e.g. 738).

–Extension:Extension: Key in the extension number.

–Group:Group: Key in the group number.

7. Press the next FT-5 Selection Key you wish to program.

8. Press to cancel any current designation.

9. Enter new designation and repeat sequence.

10.To leave programming mode, replace handset or press Ans/RlsAns/Rls.

Whilst programming, if a key is not pressed within a preset time, the

terminal will automatically leave the programming mode.

Storing External NumbersStoring External Numbers

To store an external number (up to 5) under the keypadTo store an external number (up to 5) under the keypad::

1. Take the FT-5 off-hook, press and dial 0.0.

2. Select store number from 0000 to 04.04.

3. Press to clear current value.

4. Enter external number (including 99 for an external line).

5. To leave programming mode, replace handset or press Ans/RlsAns/Rls.

Otros manuales para FT-5

Tabla de contenidos

Otros manuales de Terminal táctil de SDX Audio

SDX Audio

SDX Audio FT-5 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario