Scion-Tech SC04.1404 Manual de usuario
1
4K HDMI Matrix 4x4, HDCP 2.2
Operating Instructions
Dear Customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
Features
·HDMI 2.0 version (Support HDMI2.0 4K50/60Hz YUV420).
·Resolutions 4K@60Hz, 4K@30Hz, 1080P, 1080i, 720P.
·Supports 3D.
·HDCP 2.2/1.4 compliant.
·4xHDMI Input, 4xHDMI output with SPDIF Audio.
·Allows up to four 4 source devices to be independently switched to 4
HDMI monitors, HDTVs, or projectors.
· Support Panel Button, Local IR, RS232 Control, IP Control Via Telnet.
·1U rack design, easy installment.
Notice
Our company reserves the right to make changes in the hardware, packaging
and any accompanying documentation without prior written notice.
Scion Tech Ltd
SC04.1404
2
Warning
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this apparatus
to rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
6. Clean this apparatus
only with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
5. Do not place sources of naked
flames, such as lighted candles,
on the unit.
7. Unplug this apparatus
during lightning storms or
when unused for long
periods of time.
8. Protect the power cord
from being walked on or
pinched particularly at
plugs.
9. Only use attachments /
accessories specified by
the manufacturer.
10. Refer all servicing to
qualified service
personnel.
3
TABLE OF CONTENTS
Package Contents
Panel Descriptions
Connecting and Operating
Maintenance
Product service
Warranty
Package Contents
①Main unit. (HDMI Matrix)
②12V3A DC Power Supply.
③1x Remote controller.
④1x IR_RX (IR receiver) extension cable.
⑤Operating Instructions.
⑥2x Mounting Ear.
Specifications
Operating Temperature Range -5 to +35°C(-41 to +95 °F)
Operating Humidity Range 5 to 90 % RH (no condensation)
Input Video Signal 0.5-1.0 volts p-p
Input DDC Signal 5 volts p-p (TTL)
Signaling Rate 3.0Gbit/s
Video Format Supported 4K@60Hz/4k@30Hz/1080P/1080i/720P/576P/480P/
576i/480i
HDCP Compliant HDCP2.2 and HDCP1.4
Output Video HDMI2.0 and HDMI 1.4
Audio Format Supported DTS-HD、Dolby trueHD
Maximum Transmission Distance <15m
Power Consumption 30wtts (Max.)
Dimensions L440xW256xH42mm/ L17.3”xW10”xH1.65”
Mass (Main Unit) 2.1kg
& Note: Specifications are subject to change without notice. Mass and dimensions are
approximate.
4
Panel Descriptions
Front Panel
Rear Panel
①HDMI input port.
②HDMI output port.
③SPDIF Audio output.
④IP control.
⑤RS232 for control.
⑥For IR external receiver cable.
⑦DC power input.
Connecting
1) Connect the HDMI input sources (such as HD-DVD, PS3, STB etc) into
HDMI Matrix.
2) Connect the HDMI outputs (such as HD-LCD, HD-DLP) into HDMI Matrix.
3) Power on the input source you want to show.
4) Connect the power supply into HDMI Matrix and turn on the display you
want to watch.
5) Use remote or push the button to choose input source.
& Attention: Insert / Extract cables gently.
5
Typical Application
Operation:
1. Front panel control.
Change source to output port:
First, press an output number button to choose which output port to
change the source (the input digit above the output port number on LCD
starts to be flash).
Second, press an input number to change the source of the output port to the
selected input.
IR
In 1 In 2 In 3 In 4
Out 1 Out 2 Out 3 Out 4
6
2. Local IR remote control.
You can control the HDMI route of the matrix by using the IR remote.
There are four group key pads for two output ports. For each output port source
selection, there are 4 number keys and two arrow keys. Press number keys to
select specific input port. Left arrow button to backward the input port, and right
arrow to forward input port.
3. IR extender control.
Use the IR receiver cable to change the IR receiver position.
If controlling the HDMI Matrix through the 1/8” (3.5 mm) input jack on the rear
panel, connect the IR cable directly to the matrix rear IR receiver extension
sockets.
7
4. EDID setting.
Pressing and holding input number button for 3 seconds to recall the display
on front LCD panel for EDID setting of this input port.
For example, pressing and holding input number button 3 for 3 seconds will
recall the LCD to display the current EDID setting on input port 3:
Clicking the button In3 will display the next EDID:
When pressing and holding button In3 for 3 seconds will select the EDID
shown on LCD panel.
To copy EDID from out1 to input 3, pressing and holding In3 to
recall the display of EDID setting for input3, click button In3 13 times.
Pressing and holding In3 for 3 seconds, 4x4 matrix will try to read EDID data
from output1 and save it to input3
Below is the list for EDID options.
1：1080P_2CH(PCM)
2：1080P_ audio5.1
3：1080P_ audio7.1
4：1080P_3D_2CH(PCM)
5：1080P_3D_ audio5.1
6：1080P_3D_ audio7.1
7：4K30Hz_3D_2CH(PCM)
8：4K30Hz_3D_ audio5.1
9：4K30Hz_3D_ audio7.1
10：4K60Hz(Y420)_3D_2CH(PCM)
8
11：4K60Hz(Y420)_3D_ audio5.1
12：4K60Hz(Y420)_3D_ audio71
USER EDID 1
USER EDID 2
USER EDID 3
EDID from output1
EDID from output2
EDID from output3
EDID from output4
5. IP control module information shown on LCD panel.
Pressing In3 and In4 simultaneously for 3 seconds, IP setting information will
be shown on front LCD panel.
Other IP setting information will be shown automatically after every 3 seconds.
6. Turn on or turn off DHCP mode.
Pressing In1 and In3 simultaneously for 3 seconds to toggle the DHCP mode.
or
7. Turn on or turn off cascading mode.
When cascading is enabled, the matrix will not read EDID data from sink
device (TV) or hot plug status, it will always output the signal to the sink device
without doing any handshake. This is only when a handshake problem
happens.
When this happens, try this mode to solve the problem.
Press In1 and In2 simultaneously for 3 seconds to toggle on/off the
cascading mode.
9
8. Software Control
1). Connecting a computer to the Matrix using a USB to RS232 cable, open
the software and click Search Machine.
2). You can control HDMI Matrix as shown beow.
3). Set the EDID of 4 HDMI inputs:
10
9. IP Control
1). Click “DHCP”, then the switch will assign IP address automatically. You
can also set the IP address manually.
2). If you set a static IP, you need set the IP of the computer to:-
Tabla de contenidos
Otros manuales de Conmutador de matriz de Scion-Tech
Scion-Tech
Scion-Tech SC36.MX44 Manual de usuario
Scion-Tech
Scion-Tech SC04.MX22 Manual de usuario
Scion-Tech
Scion-Tech SC38.MX88 Manual de usuario
Scion-Tech
Scion-Tech SC35.MX44 Manual de usuario
Scion-Tech
Scion-Tech SC04.1808 Manual de usuario
Scion-Tech
Scion-Tech SC08.MX2000 Manual de usuario
Scion-Tech
Scion-Tech SC04.MX88 Manual de usuario
Scion-Tech
Scion-Tech SC38.MX16 Manual de usuario
Scion-Tech
Scion-Tech SC36 MX88 Manual de usuario
