ScienceTech Bigshot Manual de usuario
Ages 8 - 108 years
Instruction Manual
Build . Learn . Use
www.bigshotcamera.com
1
Build
Safety
Use
P.2
P.3
P.5
P.8
P.10
P.11
P.12
P.13
AGetting Started
BPower Generator
C
A
B
C
Electronics
DLens Wheel
ELED Flash
Camera Parts
Charging the Battery
Bigshot Software
P.1
Contents
1
Always ensure that the camera is operated according to the instructions below, which
are intended to prevent injuries to yourself and other persons, or prevent damage to
the camera.
WARNING: Possibility of serious injury
1. Do not trigger the flash in close proximity to people's eyes. Exposure to the intense
light produced by the flash could damage eyesight. In particular, keep the camera at
least one meter away from infants when using the flash.
2. Store the camera equipment out of reach of children below 8 years. It is dangerous
if any of the components are swallowed. If this occurs, contact a doctor immediately.
Putting the strap around a child's neck could result in asphyxiation.
3. Do not allow liquids to enter the camera. This could result in fire or electric shock.
Do not use organic solvents such as alcohol, benzene, or thinner to clean the camera.
If liquid or foreign objects come into contact with the camera interior, immediately
turn the camera power off.
4. Use only USB outlets to recharge the camera. Use of other power sources could
result in fire or electric shock.
5. The camera's battery is not replaceable. Use of other batteries could result in
explosions, fire or electric shock.
6. Do not place battery near or in direct flame. Do not attempt to disassemble or alter
the battery. Avoid dropping or subjecting battery to severe impacts. In the event that
the battery leaks and the eyes, mouth, skin or clothing contacts these substances,
immediately flush with water and seek medical assistance.
CAUTION: Possibility of injury or damage to the camera
1. Avoid using/storing camera in strong sunlight and high temperatures. These could
cause leakage, overheating or an explosion of the battery resulting in electric shock,
fire, burns and other injuries. High temperatures may also cause deformation of the
camera casing and other components.
2. Do not sit down with the camera in your pocket. Doing so may cause malfunction
or damage the LCD.
3. Do not put the camera and keys or other sharp objects into the same pocket. The
camera lenses or LCD may get scratched.
Safety
2 3
Slide gear A into the hole on the side
of the camera body. The blue arrow
tells you the direction in which to
slide the gear.
Place gear C next to the first gear as
shown, and push the rod through
both the gears until it is all the way
in. The left end of the axle should
now sit in the notch on the camera
body and the two gears should be
free to spin.
Take gear B and gear D and hold
them together as shown. Now push
the second axle rod through both
gears such that it pops out just a bit
at the other end.
Build
B1.
While holding the gear in place with
one finger, insert one of the axle rods
into the middle hole of the gear. Push
the rod in until it touches the finger
holding the gear.
B2.
B3. B4.
Take the gear assembly you just
made and place it below the first set
of gears, as shown. Make sure the
left end of the rod rests in the notch
in the camera body.
B5.
BPower Generator
Learn about gearbox
http://www.bigshotcamera.com/learn/power/gearbox
Learn about gears
http://www.bigshotcamera.com/learn/power/gears
4 5
Push the axel rod from the left all
the way so that it enters the hole
in the camera body on the right.
Place the bracket on the dynamo so
that it secures the dynamo and the
two axle rods in place.
Fasten the bracket in place with two
screws, as shown above.
Build
B6.
Place the dynamo into the camera
body. Make sure the dynamo gear
meshes correctly with gear B. Don't try
to rotate any of the gears as it may
cause the axle rods to pop out of their
positions.
B7.
B8. B9.
Take the hand crank and push-fit its
triangular notch onto the triangular
head of gear A of the gearbox.
B
10.
Fasten the hand crank onto gear A
using three screws, as shown.
B
11.
BPower Generator
Learn about dynamo
http://www.bigshotcamera.com/learn/power/dynamo
Learn about power generator
http://www.bigshotcamera.com/learn/power/index
4 5
Rotate the hand crank clockwise. If
it does not rotate smoothly, one of
the parts of the gearbox may be
misaligned. Carefully undo the
previous steps and reassemble the
gearbox.
Build
Build
B
12.
Clip the white crank cap onto the
hand crank so that it covers the three
screws. Before snapping the cover in
place, make sure you have lined up
the three tabs on the cover with the
slots on the hand crank.
B
13.
BPower Generator
Place the shoot button into the hole
on the top face of the camera body.
You will have to insert it at an angle,
as shown.
C1.
While the shoot button is in the hole,
rotate its arm clockwise until the arm
slides into the notch on the camera
body.
C2.
CElectronics
Learn about power generator
http://www.bigshotcamera.com/learn/power/index
Learn about electronic components
http://www.bigshotcamera.com/learn/electronics/index
67
Pick up the PCB module and turn
the mode knob to the position
shown above.
Fasten the PCB module onto the
camera body using three screws.
Now set the mode knob to the OFF
position. It must remain in the OFF
position during the remaining
assembly process.
Build
C3.
Insert the PCB module into the camera
body. Make sure the pillars in the
camera body go through the holes in
the PCB module.
C4.
C5. C6.
CElectronics
Learn about LCD
http://www.bigshotcamera.com/learn/lcd-display/index
Learn about electronic components
http://www.bigshotcamera.com/learn/electronics/index
Find the connector attached to the
pair of wires from the PCB that have
the same color combination as the
wires from the dynamo. Hold the two
connectors in each hand and gently
join them until they click.
C7.
67
Place the connectors from the
dynamo and the battery into the
space at the bottom of the camera
body. Make sure that the wires do
not touch the gears.
Place the clear back cover on top of
the camera body. Make sure the
screw holes on the cover align with
the screw inserts on the camera
body.
Fasten the back cover with four
screws.
Build
C
10.
Now set the battery into the camera
body as shown.
C
11.
C
12.
C
13.
CElectronics
If you want to disconnect the wires,
then press down on the smaller
connector and pull it out as shown
above.
C8.
Take the remaining connector from
the PCB module and the connector
from the battery. Gently connect the
connectors so that they click.
C9.
Learn about rechargeable battery
http://www.bigshotcamera.com/learn/power/battery
Tabla de contenidos
