Schumacher Electric INSTANT POWER XP400 Manual de usuario

00-99-001047/0710

Model / Modelo: XP400, XP500, XP750C

READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT.• FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE PRODUCTO.• CUALQUIER FALLA PODRÍA RESULTAR EN SERIAS LESIONES O PODRÍA SER

MORTAL.

OWNER’S MANUAL

•

MANUAL DEL USUARIO

INSTANT POWER™Jump Starter and DC Power Source /

Fuente de Poder de CD y Arrancador

ADVERTENCIA

XP400 XP500

XP750C

DO NOT RETURN THIS PRODUCT

TO THE STORE!

Call Customer Service for Assistance:

800-621-5485

¡NO LO DEVUELVA ESTE PRODUCTO

A LA TIENDA!

Llame a Servicios al Cliente para Asistencia:

800-621-5485

TABLE OF CONTENTS

SECTION PAGE

IMPORTANT SAFETY INSTRUCTIONS 2

PERSONAL PRECAUTIONS 3

FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY 4

GROUNDING AND AC POWER CORD CONNECTIONS 4

ASSEMBLY INSTRUCTIONS 4

FEATURES 5

CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER™ 6

OPERATING INSTRUCTIONS 7

MAINTENANCE INSTRUCTIONS 9

MOVING AND STORAGE INSTRUCTIONS 10

TROUBLESHOOTING 10

SPECIFICATIONS 11

REPLACEMENT PARTS/ACCESSORIES 12

LIMITED WARRANTY 12

ÍNDICE

SECCIÓN PÀGINA

INSTRUCCIONES IMPORTANTES DE SEGURIDAD 18

PRECAUCIONES PERSONALES 19

SIGA ESTOS PASOS CUANDO SE CONECTE A LA BATERÍA 20

CONEXIONES A TIERRA Y ENERGÍA DE CA 21

INSTRUCCIONES DE MONTAJE 21

CARACTERÍSTICAS 21

PARA CARGAR LA BATERIA INTERNA DE LA FUENTE

DEL INSTANT POWER™ 22

INSTRUCCIONES DE OPERACIÓN 23

INSTRUCCIONES DE MANTENIMIENTO 26

INSTRUCCIONES PARA EL MANEJO Y ALMACENAMIENTO 26

LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS 27

ESPECIFICACIONES 28

REPUESTOS/ACCESORIOS 29

GARANTÍA LIMITADA 29

CONTAINS SEALED NON-SPILLABLE LEAD-ACID

BATTERY. MUST BE DISPOSED OF PROPERLY.

CONTIENE UNA BATERÍA SELLADA DE ÁCIDO-

PLOMO NO DERRAMABLE QUE DEBE DESECHARSE

APROPIADAMENTE.

WARNING: Possible explosion hazard. Contact with battery acid

may cause severe burns and blindness. Keep out of reach of

children.

ADVERTENCIA: Posible Riesgo de una explosión. El contacto

con una batería de ácido puede causar quemaduras y ceguera.

Manténgase alejado de los niños.

•1 •

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

SAVE THESE INSTRUCTIONS – Charge the Instant Power™ internal battery

immediately after purchase, after every use and every 30 days. This manual

will show you how to use your Instant Power™ safely and effectively. Please

read, understand and follow these instructions and precautions carefully, as

this manual contains important safety and operating instructions. The safety

messages used throughout this manual contain a signal word, a message and

an icon.

The signal word indicates the level of the hazard in a situation.

Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in moderate or minor injury to the operator or

bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in damage to the equipment or vehicle or property

damage.

Safety messages in this manual contain two different type styles.

Unnumbered type states the hazard.•

Numbered type states how to avoid the hazard.•

The icon gives a graphical description of the potential hazard.

Pursuant to California Proposition 65, this product contains chemicals

known to the State of California to cause cancer and birth defects or

other reproductive harm.

•2 •

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS -1. This manual contains important safety and operating instructions

RISK OF ELECTRIC SHOCK OR FIRE.

Read the entire manual before using this product. Failure to do so could result1.1 in serious injury or death.

Keep out of reach of children.1.2

Use only recommended attachments. Use of an attachment not recommended1.3

orsoldbySchumacher®ElectricCorporationmayresultinariskofre,

electric shock or injury to persons or damage to property.

Donotputngersorhandsintoanyofthe1.4 Instant Power’s™ outlets.

Do not expose the1.5 Instant Power™ to rain or snow.

Use of an improper extension cord to charge the Instant Power™ could result1.6

inariskofreandelectricshock.Makesure:

That the pins on the plug of the extension cord are the same number, size•and shape as those of the plug on the Instant Power™.

That the extension cord is properly wired and in good electrical condition.•

That the extension cord has a wire size of 18 gauge (AWG) or larger and is•50 feet long or less.

To reduce the risk of electric shock, turn off and/or unplug the Instant Power™1.7 before attempting any maintenance or cleaning. Simply turning off the controls

will not reduce this risk.

Do not operate the1.8 Instant Power™ if it has received a sharp blow, been

droppedorotherwisedamagedinanyway;takeittoaqualiedservice

person. (Call customer service at: 1-800-621-5485.)

Do not disassemble the1.9 Instant Power™;takeittoaqualiedserviceperson

when service or repair is required. Incorrect reassembly may result in a risk of

reorelectricshock.(Callcustomerserviceat:1-800-621-5485.)

RISK OF EXPLOSIVE GASES.

WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS.1.10 BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY

OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT

YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE INSTANT

POWER™.

To reduce the risk of a battery explosion, follow these instructions and those1.11 published by the battery manufacturer and the manufacturer of any equipment

you intend to use in the vicinity of the battery. Review the cautionary markings

on these products and on the engine.

•3 •

PERSONAL PRECAUTIONS2.

RISK OF EXPLOSIVE GASES. A

SPARK NEAR THE BATTERY MAY

CAUSE A BATTERY EXPLOSION.

TO REDUCE THE RISK OF A

SPARK NEAR THE BATTERY:

Working in the vicinity of a lead-acid battery is dangerous. Batteries generate2.1 explosive gases during normal battery operation. For this reason, it is of

utmost importance that you follow the instructions each time you use the

Instant Power™.

NEVERsmokeorallowasparkorameinthevicinityofabatteryorengine.2.2

Do not permit the internal battery of the Instant Power™ to freeze. Never2.3 charge a frozen battery.

To prevent sparking, NEVER allow clips to touch together or contact the same2.4

piece of metal.

When charging the internal battery of the Instant Power™, work in a well2.5 ventilated area and do not restrict the ventilation in any way.

Be extra cautious to reduce the risk of dropping a metal tool onto a battery. It2.6 might spark or short-circuit the battery or other electrical part that may cause

an explosion.

Remove personal metal items such as rings, bracelets, necklaces and watches2.7 when working with a lead-acid battery. A lead-acid battery can produce a short-

circuit current high enough to weld a ring or the like to metal, causing a severe

burn.

Be sure the area around the battery is well ventilated while the jump starter is2.8 being used.

RISK OF CONTACT WITH BATTERY ACID.

BATTERY ACID IS A HIGHLY CORROSIVE

SULFURIC ACID.

Consider having someone close enough by to come to your aid when you work2.9 near a lead-acid battery.

Have plenty of fresh water and soap nearby in case battery acid contacts your2.10 skin, clothing or eyes.

Wear complete eye and body protection, including safety goggles and2.11 protective clothing. Avoid touching your eyes while working near the battery.

If battery acid contacts your skin or clothing, immediately wash the area with2.12

soapandwater.Ifacidentersyoureye,immediatelyoodtheeyewithcold

running water for at least 10 minutes and get medical attention right away.

If battery acid is accidentally swallowed, drink milk, the whites of eggs or water.2.13 DO NOT induce vomiting. Seek medical attention immediately.

Stay clear of fan blades, belts, pulleys and other parts that may cause injury.2.14

Clean the battery terminals before using the jump starter. During cleaning,2.15 keep airborne corrosion from coming into contact with your eyes, nose and

mouth. Use baking soda and water to neutralize the battery acid and help

eliminate airborne corrosion. Do not touch your eyes, nose or mouth.

Determine the voltage of the battery by referring to the vehicle owner’s manual2.16 and make sure that the output voltage of the jump starter is correct.

Make sure that the Instant Power™ cable clips make tight connections.2.17

•4 •

FOLLOW THESE STEPS WHEN CONNECTING TO A BATTERY3.

A SPARK NEAR THE BATTERY

MAY CAUSE A BATTERY

EXPLOSION. TO REDUCE THE

RISK OF A SPARK NEAR THE

BATTERY:

Attach the output cables to the battery and chassis as indicated below. Never3.1 allow the output clips to touch each other.

Position the DC cables to reduce the risk of damage by the hood, door and3.2 moving or hot engine parts. NOTE: If it is necessary to close the hood during

the jumping process, ensure that the hood does not touch the metal part of the

battery clips or cut the insulation of the cables.

Stay clear of fan blades, belts, pulleys and other parts that can cause injury.3.3

Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post3.4 usually has a larger diameter then the NEGATIVE (NEG, N, -) post.

Determine which post of the battery is grounded (connected) to the chassis.3.5 If the negative post is grounded to the chassis (as in most vehicles), see step

3.6. If the positive post is grounded to the chassis, see step 3.7.

For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the3.6 Instant Power™ to the POSITIVE (POS, P, +) ungrounded post of the battery.

Connect the NEGATIVE (BLACK) clip to the vehicle chassis or engine block

away from the battery. Do not connect the clip to the carburetor, fuel lines or

sheet-metal body parts. Connect to a heavy gauge metal part of the frame or

engine block.

For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the3.7 Instant Power™ to the NEGATIVE (NEG, N, -) ungrounded post of the battery.

Connect the POSITIVE (RED) clip to the vehicle chassis or engine block away

from the battery. Do not connect the clip to the carburetor, fuel lines or sheet-

metal body parts. Connect to a heavy gauge metal part of the frame or engine

block.

When disconnecting the Instant Power™, turn all switches to off (if applicable),3.8 remove the clip from the vehicle chassis and then remove the clip from the

battery terminal.

GROUNDING AND AC POWER CORD CONNECTIONS4.

RISK OF ELECTRIC SHOCK OR FIRE.

The Instant Power™ internal charger plug is for use on a nominal 120-volt4.1 circuit. The extension cord utilized with the internal charger plug must be

plugged into an outlet that is properly installed and grounded in accordance

withalllocalcodesandordinances.Theplugpinsmusttthereceptacle

(outlet). Do not use with an ungrounded system.

ASSEMBLY INSTRUCTIONS5.

Remove all cord wraps and uncoil the cables prior to using the Instant

Power™.

•5 •

FEATURES6.

XP400

Battery Status Indicators1.

Battery Status Switch2.

Built-In Worklight3.

Worklight ON/OFF Switch4.

12V DC Power Outlet5.

Internal Battery Charger Plug6. (not shown)

Battery Clips7.

XP500

Battery Status Indicators1.

Battery Status Switch2.

Built-In Worklight3.

Worklight ON/OFF Switch4.

12V DC Power Outlet5.

Internal Battery Charger Plug6. (not shown)

Battery Clips/USB ON/OFF Switch7.

USB Port8.

Battery Clips9.

XP750C

Battery Status Indicators1.

Battery Status Switch2.

12V DC Power Outlet3.

Internal Battery Charger Plug4. (not shown)

Battery Clips/USB ON/OFF Switch5.

USB Port6.

Built-In Worklight7.

Worklight ON/OFF Switch8.

Air Compressor ON/OFF Switch9. (not shown)

Air Compressor Gauge (not shown)10.

Air Compressor Hose11.

Air Compressor Hose Wrap Cleats12.

(not shown)

Air Compressor Adapters and13.

Storage Bag (not shown)

Battery Clips14.

14 11

•6 •

CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER™7.

IMPORTANT: CHARGE IMMEDIATELY AFTER PURCHASE, AFTER EACH

USE AND EVERY 30 DAYS TO KEEP THE INSTANT POWER™ INTERNAL

BATTERY FULLY CHARGED.

LED Indicators:7.1

TO CHECK THE INTERNAL BATTERY’S CHARGE STATUS, PRESS THE

BATTERY STATUS BUTTON ON THE FRONT OF THE INSTANT POWER™.

The LED lights will indicate the charge level as follows:

A red LED indicates a 50% or less charge and you should immediately•recharge the Instant Power™.

A yellow LED indicates a 50 to 75% charge. The Instant Power™ may be•used but should be recharged as soon as possible.

A green LED indicates the internal battery is fully charged.•

Charging the Internal Battery using the Built-In Charger:7.2

Tocharge,ipthechargerplugonthebackoftheInstantPower™upand1. plug an 18 gauge (AWG) or larger extension cord onto it. (Extension cord

not included; must be purchased separately.)

Plug the extension cord into a 120V AC electrical wall outlet.2.

The RED LED will glow indicating charging.3.

The GREEN LED will light when the battery has reached full charge. This4. could take up to 72 hours due to the age and condition of the battery. The

charger will automatically go into maintain mode and maintain the battery at

full charge without damaging it.

Charge the Instant Power™ as soon as possible after use.5.

Do not use the Instant Power™ while charging the internal

battery.

You may also charge the internal battery while driving, using the male-to-male

charger cable (p/n 94500109 – not included). Insert one end of the accessory

cable into the 12V DC power outlet and the other end into the vehicle’s

accessory outlet (lighter socket). Completely disconnect the charger cable

when the engine is not running.

The RED LED and the GREEN LED do not operate during

this method of charging. Using this method to charge the battery overrides the

maintain mode and the battery can be overcharged. Monitor the progress of

the battery and when it reaches a full (100%) charge, disconnect the charger.

Do not leave the battery unattended or it could explode causing property

damage or personal injury.

Otros manuales para INSTANT POWER XP400

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Arranque remoto de Schumacher Electric

Schumacher Electric

Schumacher Electric INSTANT POWER IP-125 Manual de usuario

Schumacher Electric

Schumacher Electric INSTANT POWER IP-1875C Manual de usuario

Schumacher Electric

Schumacher Electric DSR141 Manual de usuario

Schumacher Electric

Schumacher Electric INSTANT POWER XP400 Manual de usuario

Schumacher Electric

Schumacher Electric SL1316 Manual de usuario

Schumacher Electric

Schumacher Electric FARM & RANCH FR01241 Manual de usuario

Schumacher Electric

Schumacher Electric SL1517 Manual de usuario

Schumacher Electric

Schumacher Electric DSR141 Manual de usuario

Schumacher Electric

Schumacher Electric IP-125C Manual de usuario

Schumacher Electric

Schumacher Electric ip-75 Manual de usuario

Schumacher Electric

Schumacher Electric ProSeries PSJ-2212 Manual de usuario

Schumacher Electric

Schumacher Electric SL1317 Manual de usuario

Schumacher Electric

Schumacher Electric SL1441 Manual de usuario

Schumacher Electric

Schumacher Electric XJS22 INSTANT POWER Manual de usuario

Schumacher Electric

Schumacher Electric SL1314 Manual de usuario

Schumacher Electric

Schumacher Electric SL1464 Manual de usuario

Schumacher Electric

Schumacher Electric SL1452 Manual de usuario

Schumacher Electric

Schumacher Electric PSJ-1812 Manual de usuario

Schumacher Electric

Schumacher Electric SL1316I Manual de usuario

Schumacher Electric

Schumacher Electric SL1519 Manual de usuario

Schumacher Electric

Schumacher Electric SL1396 Manual de usuario

Schumacher Electric

Schumacher Electric SJ2 Manual de usuario

Schumacher Electric

Schumacher Electric SL1474 Manual de usuario

Schumacher Electric

Schumacher Electric INSTANT POWER IP-1875C Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual