Schlage M400 Series Manual de usuario
*44487296*
44487296
M490 Armature
plate assembly
M420/M450
Armature plate assembly
Single Electromagnetic Locks: M420, M450, M490
M400 Series
Installation Instructions
Features
Automatic Voltage Selection (AVS)
Magnet immediately detects 12VDC or 24VDC when power is
connected.
Anti-Tamper Switch (ATS)
An indication is provided should the magnet cover become
unsecured from lock.
Magnetic Bond Sensor (MBS)
Detects proper bond between magnet and armature. It can be
monitored remotely and locally with an LED.
LED
Provides local indication of MBS status.
Door Position Switch (DPS)
Indicates whether door is open or closed. This feature is used in
conjunction with the MBS.
Relock Time Delay (RTD)
Relock time can be changed. Range is 1 - 30 seconds.
Models
M420 (Trafc Control)
UL1034 and 10C/500lb and 3hr rating
M450 (High Security)
UL1034 and 10C/1000lb and 3hr rating
M490 (Max Security)
UL1034 and 10C/1500lb and 3hr rating
Trims
Basic
Auto Voltage Selection (AVS) for 12 or 24VDC
Plus
Basic features + Door Position Switch (DPS), Magnetic Bond
UL Requirements
• Units shall not impair operation of panic hardware mounted on door.
• Units shall not impair intended operation of an emergency exit.
• Units/Models are intended to be connected to UL Listed Equipment, not
intended for Burglar or Fire Alarm Initiating or Indicating Devices.
• Ambient Conditions - “For Indoor Use Only”.
• This device complies with part 15 of FCC rules.
Operation is subject to following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including any
interference that may cause undesired operation. Changes or
modications not expressly approved by party responsible for compliance
could void user’s authority to operate equipment.
2
Electrical Specications
Model Amps (12VDC)
Per Lock
Amps (24VDC)
Per Lock
Holding Force (lbs)
Per Coil
M420 0.750 0.380 500
M450 0.750 0.380 1000
M490 0.650 0.350 1500
Lock Installation
1 Prepare for installation.
1a Determine Proper Magnet Orientation
• Magnet should be placed opposite of door hinges.
Wiring
Cover
Magnet
LHR Door - Shown from Exterior
Wiring
Cover
Magnet
RHR Door - Shown from Exterior
1b Reorient Magnet (if necessary).
• Remove screws, wiring cover and end blocks.
End Block
Magnet
End Block
(with screw hole)
• Rotate magnet, end blocks and wiring cover as shown, then reassemble.
Magnet
Wiring Cover
End Block
(with screw hole)
1c Place template and mark holes.
• Place template on top corner, opposite of hinges.
• Mark holes and prepare them per template.
LHR
RHR
3
4
2 Install MBS indicator (optional, plus models ONLY).
2a Remove cover. 2b Drill hole for MBS indicator.
Bottom
0.75"
(19 mm)
¹⁄₄" (6 mm) drill bit
M420: 0.50" (13 mm)
M450/490: 0.75” (19 mm)
0.25"
(6 mm)
hole
2c Install MBS indicator.
3 Install ATS (optional, plus models ONLY)
3a Remove end block and wiring cover.
a
c
b
3b Install ATS and Reassemble
d
e
f
ATS
5
4 Attach armature to door.
4a Install armature holder.
Armature holder screws
must be flush to inside
of armature holder.
2x
OUTSIDE
4b Install armature plate as shown for door type (M420/M450 shown).
Armature bolt must be
tightened to 120 in-lbs. IncorrectCorrect
Sex Nut
Flat Washer
Wood Door Reinforced Metal Door Hollow Metal Door
Star Locking Washer
Armature
Bolt*
Z\x” hole
through
Cone Washer
Armature Plate
Armature Holder
Flat Washer
Star Locking Washer
Armature
Bolt*
Cone Washer
Armature Plate
Armature Holder
Sex Nut
Flat Washer
Star Locking Washer
Armature
Bolt*
Cone Washer
Armature Plate
Armature Holder
Z\x” hole
ZZ\cx”
hole
Drill and
tap for
B\zn - 18
machine
screw
6
5d Align magnet to armature.
• Close door.
• Press magnet to fully engage with armature.
• Mark bracket location.
Press magnet to armature
INSIDE
Mark here
5e Fully attach bracket.
• Remove magnet from bracket.
• Check bracket alignment with marks.
• Fully tighten two screws in slotted holes.
• Drill four (4) remaining holes.
• Fully tighten all screws.
Fully tighten
all screws
Drill four (4) holes
Check
alignment
OUTSIDE
Actual Size Reinforced
Metal
Sheet
Metal Use 10-24 tap
if reinforced metal
5 Install mounting bracket into frame.
5a Attach mounting bracket temporarily
• Install two middle screws into slots and partially tighten.
Partially
tighten
Pull wires
OUTSIDE
Actual Size
Reinforced
Metal
Sheet
Metal
5b Remove wiring cover. 5c Slide magnet onto bracket.
OUTSIDE
7
6 Install lock
6a Install magnet and secure with screws
Actual Size
7 Connect wiring to board (standard model)
7a Review wiring connections
TB1
Printed Circuit Board
DC Power DC (+)
DC (-)
From Magnet
7b Connect wires to board
From Door Frame
DC Power Wires
From Magnet
7c Install cover.
© Allegion 2014
Printed in U.S.A.
44487296 Rev. 01/14-e
Customer Service
1-877-671-7011 www.allegion.com/us
8 Connect wiring to board (plus model).
8a Review wiring connections.
TB1
TB2
TB3
DC Power
NO
NC
C
NO
NC
C
DC (+)
DC (-)
MBS: 1A, 30VDC, Resistive
Contacts shown
in de-energized state
DPS: 0.25A, 30VDC, Resistive
Contacts shown
in open-door state
From Magnet
Printed Circuit Board
From LED
From MBS
From MBS
RTD Adjuster
RED
Polarized
Black/Red
Note: Two MBS
plugs are
interchangeable
Min.
Time
Max.
Time
8b Connect wires to board.
From Magnet
From Door Frame
Multi Wire Cable
From LED
From MBS (2)
From MBS (1)
8c Connect ATS wires.
ATS
NC (violet)
NO (gray)
C (white)
Switch Rating:
1A @ 30VDC, Resistive
8d Install Cover
Additional Notes: Revision History Revision Description:
E > Revised artwork
1. Fold booklet style A B C D E F
14803 n/a 17855 35405
Material
White Paper
Edited By Approved By EC Number Release Date
P. Bockelman M. Sasso 43034 01-01-14
Notes
1. printed two sides
2. printed black
3. tolerance ± .13
4. printed in country may vary
5. drawings not to scale
Title
M400 Series Instruction Sheet
Creation Date
10-05-10
Number
44487296
Revision
E
Created By
M. Coleman Activity
3899 Hancock Expwy
Security, CO 80911 © Allegion 2014Software: InDesign CS6
17.000
11.000
BEGINNING SHEET
FRONT
8.500
11.000
FOLDED SHEET
FRONT
Otros manuales para M400 Series
2
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cerrar de Schlage
Schlage
Schlage M490DE Manual de usuario
Schlage
Schlage AD-Series Manual de usuario
Schlage
Schlage S-480 Manual de usuario
Schlage
Schlage BE365 Manual de usuario
Schlage
Schlage FE59 FLA CAM LH Manual de usuario
Schlage
Schlage J Series Manual de usuario
Schlage
Schlage B-Series Manual de usuario
Schlage
Schlage S-7100 Manual de usuario
Schlage
Schlage TouchScreen Deadboltwith Alarm Manual de usuario
Schlage
Schlage AD-200 Manual de usuario
Schlage
Schlage Ease S1 SMART DEADBOLT Manual de usuario
Schlage
Schlage SchlageTouch BE375 Manual de usuario
Schlage
Schlage BE365 Manual del propietario
Schlage
Schlage CM5100-FSA-KPI Manual de usuario
Schlage
Schlage L400 Series Manual de usuario
Schlage
Schlage SENSE Manual de usuario
Schlage
Schlage LINK FE599 Manual de usuario
Schlage
Schlage L9010 Manual de usuario
Schlage
Schlage AD-400 Manual de usuario
Schlage
Schlage LINK FE599 Manual de usuario
