Schlage L400 Series Manual de usuario
*P516-911*
P516-911
1 Prepare the door for indicator trim
Two Z\," pilot holes are required to mount the indicator.
ONLY ONE SIDE OF THE DOOR – THE INDICATOR SIDE –
REQUIRES THIS PREPARATION. Use the template included in
the package to mark the location of the pilot holes before drilling.
Inside of door Outside of door
¹⁄₈" pilot
hole x 2
¹⁄₈" pilot
hole x 2
For indicator
thumb turn
only
For indicator
thumb turn
only
2 Install lock chassis
Note:
Pilot holes for
INDICATOR
ONLY
DO NOT FULLY TIGHTEN
CHASSIS MOUNTING SCREWS.
Indicator trim is available for either the inside or outside of the door on allowable functions.
Non-indicator trim is furnished on the opposite side of the door.
The L400 lock with indicator is not intended for exterior door applications.
For retrot, see page 6.
Check the door preparation dimensions with the template included in the package.
Tools
Thumb turn
Indicator trim
Cylinder turn
L400 Series Lock with Indicator Sectional Trim
L400 Lock with Indicator
Installation Instructions
2
3 Install outside cylinder - NON-INDICATOR ONLY
FOR INDICATOR, SKIP TO STEP 4.
3a Insert key halfway into the cylinder.
L463
Exterior
3b Rotate cylinder clockwise.
Key inserted
halfway
4 Install outside cylinder - INDICATOR
4a Install the indicator mounting plate.
Mounting plate
4b Adjust the cam spindle length.
Cut the spindle at the appropriate mark
according to door thickness.
For 2Z\v” door do not cut the spindle.
4c Install the indicator slide and cam.
Indicator
slide
Cam
4d Connect the cam to the indicator slide. The cam must
engage either the left or right side of the indicator slide
according to door handing and indicator location.
• Unlock the door.
• Move the indicator slide against the top rim of the
mounting plate (unlocked position).
• Assemble the cam as shown.
Door Hand/Indicator Location
Lock Type
Non-deadbolt
functions
RH/Outside
LH/Inside
RH/Inside
LH/Outside
Deadbolt
functions
RH/Inside
LH/Outside
RH/Outside
LH/Inside
3
4e Insert key halfway into the cylinder.
4f Install the indicator faceplate and cylinder with cylinder
spring as shown.
L463
4g Rotate cylinder clockwise.
5 Install inside cylinder or thumb turn –
NON-INDICATOR ONLY
FOR INDICATOR, SKIP TO STEP 6.
Cylinder
5a Insert key halfway into the cylinder.
L463
5b Rotate cylinder clockwise.
— OR —
Thumb turn
Rotate 180°
Extend
deadbolt
Thumbturn
vertical
4
6 Install inside cylinder – INDICATOR
6a Install the indicator mounting plate.
Mounting plate
6b Adjust the cam spindle length.
Cut the spindle at the appropriate mark
according to door thickness
For 2Z\v” door do not cut the spindle.
6c Install the indicator slide and cam.
Cam
Indicator
slide
6d Connect the cam to the indicator slide. The cam must
engage either the left or right side of the indicator slide
according to door handing and indicator location.
• Unlock the door.
• Move the indicator slide against the top rim of the
mounting plate (unlocked position).
• Assemble the cam as shown.
Door Hand/Indicator Location
Lock Type
Non-deadbolt
functions
RH/Outside
LH/Inside
RH/Inside
LH/Outside
Deadbolt
functions
RH/Inside
LH/Outside
RH/Outside
LH/Inside
6e Insert key halfway into the cylinder.
6f Install the indicator faceplate and cylinder with cylinder
spring as shown.
Key inserted
halfway
Indicator
faceplate
L463
5
6g Rotate cylinder clockwise.
7
7a Tighten cylinder mounting screw.
7b Tighten top and bottom chassis mounting screws.
Cylinder
mounting
screw
ab
Chassis
mounting
screws
8 Install armor front
For retrofit instructions, see page 6.
6
INDICATOR LOCK RETROFIT INSTRUCTIONS
1 Remove armor front
2 Remove cylinder(s) or thumb turn if applicable
2a Loosen the cylinder mounting screw.
2b Remove the inside cylinder or thumb turn.
Cylinder
Key inserted
halfway
Rotate cylinder counterclockwise
— OR —
Thumb turn
Rotate 180°
Extend
deadbolt
2c Remove the outside cylinder.
Key inserted
halfway
Rotate cylinder
counterclockwise
3 Check door preparation
IMPORTANT
• To install the indicator trim, additional door preparation may be required. If additional door preparation is required, remove
the lock chassis from the door before drilling. Steps for reassembly are included in this instruction sheet.
• Please refer to the template included in this package.
• Make sure the door is prepared with any necessary holes for the indicator trim.
4 Complete installation of indicator trim
Go to STEP 4 ON PAGE 2 and follow the instructions to complete the installation of the indicator trim.
Customer Service
1-877-671-7011 www.allegion.com/us
8
1 Preparar la puerta para el borde con indicador
Préparer la porte pour la garniture d’indicateur
Se requieren dos oricios piloto de Z\,” para montar el
indicador.
SOLO UN LADO DE LA PUERTA – el lado del indicador –
requiere esta preparación. Use la plantilla incluida en el paquete
para marcar la ubicación de los oricios piloto antes de perforar.
Deux trous pilotes de 32 mm (Z\, po) sont requis pour
installer l’indicateur.
SEUL UN CÔTÉ DE LA PORTE – le côté indicateur – exige
cette préparation. Utilisez le gabarit inclus dans l’emballage pour
marquer l’emplacement des trous pilotes avant de les percer.
Interior de la puerta
Intérieure de la porte
Orificios
piloto de ¹⁄₈"
Trous pilotes
(¹⁄₈" po)
x 2
Exterior de la puerta
Extérieure de la porte
Orificios
piloto de ¹⁄₈"
Trous pilotes
(¹⁄₈" po)
x 2
El borde con indicador está disponible para el interior o el exterior
de la puerta para las funciones permitidas. El borde sin indicador
se coloca en el lado opuesto de la puerta.
La cerradura L400 con indicador no está destinada para
aplicaciones en puertas exteriores.
Para una adaptación, vea la página 15.
La garniture d’indicateur est vendue pour l’Intérieur ou l’extérieur de
la porte pour les fonctions autorisées. Une garniture sans indicateur
est fournie pour le côté opposé de la porte.
La serrure L400 avec indicateur n’est pas conçue pour des
utilisations sur une porte extérieur.
Pour la rénovation, reportez-vous à la page 15.
Compruebe las dimensiones de preparación de la puerta con la plantilla incluida en el paquete.
Vériez les dimensions de préparation de la porte à l’aide du gabarit inclus dans l’emballage.
Herramientas / Outils
Cilindro giro
Cylindre tournante
Giro manual
Barrette
tournante
Borde con indicador
Garniture d’indicateur
Cerradura Serie L400 con seccional de seguridad con indicador
Serrure de la série L400 avec sectionnel d’indicateur d’entrée de serrure
Cerradura L400 con indicador
Serrure L400 avec indicateur
Instrucciones de instalación
Notice d’installation
10
2 Instale el chasis de la cerradura
Installez le bâti de la serrure
Nota: Oricios
piloto solo para
el indicador
Remarque :
Trous pilotes
pour indicateur
uniquement
NO AJUSTE POR COMPLETO LOS
TORNILLOS DE MONTAJE DEL CHASIS.
NE SERREZ PAS COMPLÈTEMENT
LES VIS DE MONTAGE DU BÂTI.
3 Instale el cilindro externo – para BORDE SIN
INDICADOR
Installez le cylindre extérieur – pour la GARNITURE
SANS INDICATEUR
PARA BORDE DE INDICADOR, PASE AL PASO 4.
POUR LA GARNITURE AVEC INDICATEUR,
PASSEZ À L’ÉTAPE 4.
3a Introduzca la llave a mitad de camino en el cilindro.
Insérez la clé à moitié dans le cylindre.
L463
Exterior
Extérieur
3b Gire el cilindro en sentido horario.
Tournez le cylindre dans le sens horaire.
Llave insertada a
mitad de camino
Clé insérée à
moitié
Otros manuales para L400 Series
1
Tabla de contenidos
Idiomas:
Otros manuales de Cerrar de Schlage
Schlage
Schlage CO-100 Manual de usuario
Schlage
Schlage CONNECT Instrucciones de montaje
Schlage
Schlage B260 Series Manual de usuario
Schlage
Schlage AD-250 Manual de usuario
Schlage
Schlage BE469 Manual de usuario
Schlage
Schlage TouchScreen Deadboltwith Alarm Manual de usuario
Schlage
Schlage FE59 FLA CAM LH Manual de usuario
Schlage
Schlage L9000 Series Manual de usuario
Schlage
Schlage FA Series Manual de servicio
Schlage
Schlage S-7100 Manual de usuario
Schlage
Schlage LT Series Manual de servicio
Schlage
Schlage B80 Manual de usuario
Schlage
Schlage EncodePlus Manual de usuario
Schlage
Schlage S-7100 Manual de usuario
Schlage
Schlage AD-402 Manual de usuario
Schlage
Schlage CM993 Series Guía de configuración rápida
Schlage
Schlage Price Book 70A Guía del producto
Schlage
Schlage ND Series Manual de usuario
Schlage
Schlage SchlageTouch BE375 Manual de usuario
Schlage
Schlage GF3000 Gravity Force Series Manual de usuario
